JVC VN-C205 manual When installing the Camera to the electrical box, Adjusting the focal length

Page 13

Preparation (Step 1 Connection/Installation)

1-2 Mounting the Camera to the Ceiling (Continued)

3. Adjustment of the camera’s angle of view (Continued)

1-3 When installing the Camera to the electrical box

The camera can be mounted directly onto an electrical box.

Focal length

adjustment ring IRIS LEVEL

3.

Focus ring

Rotation levers

Adjusting the focal length

1 Turn the securing screw of the focal

adjustment ring counterclockwise.

2 Adjust the focal length.

3 Turn the securing screw clockwise to secure the focal adjustment ring.

Adjusting the focus

Adjust using the focus ring.

1 Set the FOCUS ADJ. switch to “ON”. The aperture is opened, decreasing the depth of field, making it easier to adjust the focus.

2 Adjust the focus.

*Repeat steps 1 to 3 of “Adjusting the image size” and “Adjusting the focus”.

3 After adjustment is complete, set the FOCUS ADJ. switch to “OFF”.

1.

2.

4 inch square electrical box

1. Open a hole in the ceiling.

Open a 140mm (5-1/2 inches) hole in the

ceiling.

2. Mount the electrical box.

The camera can be mounted on a 4-inch

square electrical box.

For instructions on mounting the electrical box,

ask your dealer.

3. Follow steps 2 to 6 of mounting the

Camera to the Ceiling (Preparations)

(page 16)

4. Follow steps 1 to 7 of mounting the

Camera to the Ceiling (Installation)

(page 21)

5. Mount the camera to the electrical box.

3.Settings related to video

Perform the settings using “Video setting switch” ( page 11) if necessary.

Note

4.

Settings related to video can only be

performed using “Video setting switch” on

 

 

the camera unit. Changes cannot be

 

performed via the network.

4.Attach the dome cover

Set the dome cover to the unit by aligning the 3 marks on the camera and dome cover (I, II and III). Be sure a click is heard.

CAUTION

Be sure that the dome cover is firmly at- tached. Improper attachment could result in the cover dropping down.

Mounting holes

Mounting

holes

5. Screws

Secure the camera to the electrical box using

two mounting holes.

6. Follow “Mounting the Camera to the

Ceiling (Adjustment of the camera’s

angle of view)”.

(page 23)

24

 

 

 

25

Image 13
Contents VN-C205 VN-C205INSTRUCTIONSInformation for USA Not apply to all appliancesContents Introduction SettingsPreparation Settings OperationOperating Precautions CharacteristicsIntroduction Operating Environment Name and Function of Parts Latest UpdatesVideo setting switch Connection Examples Preparation ProcedureInstallation Flowchart of installation work for camera Getting StartedAdjustment of the camera’s angle of view PreparationMounting the Camera to the Ceiling Preparation Connection/InstallationPreparations  Inserting the CF card Preparations  Connection to Alarm Input/Output TerminalConnect the input power supply cable Connect the alarm terminalConnect the LAN cable Point the camera in the direction you wish to captureAdjusting the iris level Adjusting the focal length When installing the Camera to the electrical boxAdjusting the focus Settings related to videoPull out the cables aside and mount Installing the SoftwareWhite-spot correction Settings Network Settings Setting PCs IP Address Windows XPClick Select Internet Protocol TCP/IP and click PropertiesFor Windows 2000, set according to the following procedure Setting PCs IP Address WindowsSelect Settings and click Properties Set IP address toCheck settings This VN-C205U Setup Tool only allows connection of VN-C205For other settings, next Click Start up the V.Networks Controller.Authorization Level Allowed Access Other Settings Using the VN-C205U Setup ToolAll operations using the V.Networks Controller Viewing of motion images onlyOther Settings Using the VN-C205U Setup Tool 2. Multicast Perform area setting Alarm Input This section describes procedures for alarm settingOperation when an alarm input is activated Detect Mode Alarm 1/AlarmAlarm Output Alarm FTPOutput  Alarm Output Function/Set ValueOutput Set Values Output ValueRecording time Setting the Advance screenRecording files Other Settings Using the VN-C205U Setup Tool 7. FTP Server Other Settings Using the VN-C205U Setup Tool 6. WebStart up the VN-C205U Setup Tool and select FTP Server Displaying still images uploaded to the /user folderError recovery Connection error PasswordTransfer error Alarm FTP Upload SettingWhen NTP is used Start up the VN-C205U Setup Tool and select TimeStart up the VN-C205U Setup Tool and select Memory Info High Speed NormalConnect to VN-C205 Starting Up V.Networks Controller Features that Allow Setting Using the V.Networks ControllerSelect View Specify Image Size and Upside Down settings Settings Setting Using the V.Networks ControllerMotion Detection Standby Image Size and InversionOperations Setting Using the V.Networks Controller Image Quality SettingFrame Rate Alarm Setting Select Setting and Property Perform setting Select Setting and Time Stamp Perform settingWhen alteration is complete, click Time StampRecord/Stop Playback Operations Operation Using the V.Networks ControllerPlay button Click Playback screen is displayedSnapshot Operating Environment Access Authorization LevelOperations Operating Using a Web Browser Setting Using the Web BrowserStarting Up the Web Browser Setting Using the Web Browser 1. Other Settings Setting Using the Web Browser 2. View Setting Click to apply settings and to save the set values Setting Using the Web Browser 3. Alarm Setting Alarm  Alarm OutOperations Setting Using the Web Browser Setting Using the Web Browser 4. FTP SettingViewing Live Images Viewing Still ImagesSymptom Causes/Remedial Actions TroubleshootingImage Link Displaying a still imageOthers Specifications120 Template テンプレート