Introduction
Name and Function of Parts (Continued)
Body Surface
View when the dome cover is removed.
For instructions on removing the dome cover, see step 4 of “Mounting the Camera to the Ceiling”.
% |
) [AGC - ON/OFF] |
Setting this switch to “ON” automatically in |
(☞page 17)
8
9
0
!
Video setting switch
&*
^ 
(
)
⁄
¤
‹
›
fi
This is a |
It is used for connecting to the network via |
LAN cables. (☞ Page 20) |
Pin No. | Signal Name | ||
1 | Alarm Output |
| Alarm Output 1 |
2 |
| Alarm Output 2 | |
|
| ||
3 | Alarm Input |
| Alarm Input 1 |
4 |
| Alarm Input 2 | |
|
| ||
5 |
| GND | |
^Focal length adjustment ring
Use the fastening screw adjustment ring to
set the image size and fix it with fastening screw. (☞ Page 24)
creases the sensitivity even when the bright |
ness of the subject is insufficient. |
(Default setting: ON) |
⁄[BLC - ON/OFF] Backlight Compensation switch
Setting this switch to “ON” opens the iris even in backlight conditions, making the subject easier to view.
(Default setting: OFF)
¤[AUTO/MANU] White Balance Automatic/ Manual switch
For selecting whether to adjust the white bal- ance automatically or manually.
(Default setting: AUTO)
| @ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
| # $ | % | ||||||
8 | Head | ! MONITOR terminal (RCA pin) | ||||||
| For adjusting the lens, focus, or camera angle. | For connecting a monitor when mounting the | ||||||
| (☞ page 23 to 24) | camera for adjusting the lens or determining | ||||||
9 | Tilt lock screws | the camera angle. (High impedance) | ||||||
|
|
|
|
|
| |||
&Focus ring
Use the fastening screw adjustment ring to
set the focus and fix it with fastening screw. (☞ Page 24)
Video setting switch
* [D/N - ON/OFF] Easy Day & Night switch |
To capture a subject with continually chang- |
ing brightness (day/night), set this switch to |
“ON”. The camera automatically captures the |
‹[R/B] Manual WHITE adjustment button This button is pressed when manually adjust- ing the white balance.
This feature is enabled when the “MANU” is selected using ¤ [AUTO/MANU] switch.
Press the B button to increase the blue tint and decrease the red tint.
› [RESET] Manual WHITE reset button |
When this button is pressed, the value of the |
white balance adjusted manually is reset to |
Use when adjusting the angle of view of the camera. (☞ Page 23)
0[IRIS LEVEL] Iris level adjustment
For adjusting the level of the automatic aper- ture control lens. This adjustment only needs to be made when required. Use this to accom- modate particular shooting conditions.
Turning direction of level
To darken image Counterclockwise (L side)
To brighten image Clockwise (H side)
Note
●When adjusting the iris level, set the AGC switch to “OFF”. Otherwise, when the level is turned too far toward L, the AGC function activates increasing sensitivity and the picture may look uneven.
@Wire clamp
When pulling out the cables from the side of camera unit without opening a hole on the ceiling, arrange the all the cables by bundling them into this wire clamp.
#[ALARM IN/OUT] Alarm Input/Output Terminals
Terminals for alarm input and output. (☞ Page 18)
$CF card Slot
Insert the CF card. (☞ Page 19)
image in color when the subject is bright, and |
in black and white mode when it is dark. |
(Default setting: OFF) |
Caution
The Easy Day & Night feature on this camera uses a sensitized black and white mode unlike other black and white surveillance cameras that use
([FOCUS ADJ. - ON/OFF] focus adjustment switch
When adjusting the focus during installation,
setting this switch to “ON” will open the iris.(Default setting: OFF) (☞ page 24)
the default value. |
fi[SPOT CORRECTION] White-spot correc- tion button
When this button is pressed, white spots are corrected.
For instructions on correcting
“About
10 |
|
|
| 11 |