JVC VN-C205 Mounting the Camera to the Ceiling, Preparation Connection/Installation, Preparations

Page 9

Preparation (Step 1 Connection/Installation)

1-2 Mounting the Camera to the Ceiling

Cautions

Ceiling

Attachment of a embedded cover in the ceiling (recess bracket) may be mandatory in certain regions. If this is so, ensure that the embedded cover (recess bracket) is securely attached before installing the camera.

Please refer to the instruction manual for the cover in use for details on installation of the embedded cover (recess bracket).

For more detail, please contact the JVC.

 

4. Remove the dome cover.

 

Turn the dome cover anticlockwise and

4.

remove it as shown in the diagram.

* When pulling out the cables to mount the

 

camera, press the perforations of the dome

 

cover with finger to open the hole for pulling

 

out the cables. (Page 9)

 

5. Do the wirings for the alarm cable

 

Remove the terminal block of the alarm cable

 

from the camera unit and do the wirings.

Embedded Cover in Ceiling (recess bracket)

1. Preparations

Open hole in ceiling, connect cables and mount camera to ceiling.

(Page 18)

6. Insert the CF card into the camera unit

Insert the CF card into the camera unit when

necessary. (Page 19)

1.

20 mm

(3/4 inches)

Input power cable

LAN cable

Video signal cable

2.

Approx.100 mm (3-7/8 inches)

1.Open a hole in the ceiling.

Use the template and open a hole in the ceiling for the cables.

Note

There is no need to open a hole in the ceiling when using the cable extraction hole on the side of the camera.

(Refer to step 4. on page 17)

2. Pull out the cables from the ceiling.

Alarm signal cable

Safety cable

3.

16

Before connecting, pull out the input power

cable and video signal cables about 100 mm

(3-7/8 inches) from the ceiling.

3. Attach the safety cable to the camera.

(Safety cable is not included)

Attach the safety cable to the back of the

camera.

Cautions

To avoid unforeseen accidents, attach the safety cable.

Select a suitable safety cable based on length, strength, location, material (insulation property), etc.

Always use the M2.6 x 6 screws mounted on the unit.

17

Image 9
Contents VN-C205 VN-C205INSTRUCTIONSInformation for USA Not apply to all appliancesContents Introduction SettingsPreparation Settings OperationCharacteristics Operating PrecautionsIntroduction Operating Environment Name and Function of Parts Latest UpdatesVideo setting switch Connection Examples Preparation ProcedureInstallation Flowchart of installation work for camera Getting StartedAdjustment of the camera’s angle of view PreparationPreparation Connection/Installation Mounting the Camera to the CeilingPreparations  Inserting the CF card Preparations  Connection to Alarm Input/Output TerminalConnect the input power supply cable Connect the alarm terminalConnect the LAN cable Point the camera in the direction you wish to captureAdjusting the iris level Adjusting the focal length When installing the Camera to the electrical boxAdjusting the focus Settings related to videoInstalling the Software Pull out the cables aside and mountWhite-spot correction Settings Network Settings Setting PCs IP Address Windows XPClick Select Internet Protocol TCP/IP and click PropertiesFor Windows 2000, set according to the following procedure Setting PCs IP Address WindowsSelect Settings and click Properties Set IP address toCheck settings This VN-C205U Setup Tool only allows connection of VN-C205For other settings, next Click Start up the V.Networks Controller.Authorization Level Allowed Access Other Settings Using the VN-C205U Setup ToolAll operations using the V.Networks Controller Viewing of motion images onlyOther Settings Using the VN-C205U Setup Tool 2. Multicast Perform area setting This section describes procedures for alarm setting Alarm InputOperation when an alarm input is activated Detect Mode Alarm 1/AlarmAlarm Output Alarm FTPOutput  Alarm Output Function/Set ValueOutput Set Values Output ValueSetting the Advance screen Recording timeRecording files Other Settings Using the VN-C205U Setup Tool 7. FTP Server Other Settings Using the VN-C205U Setup Tool 6. WebStart up the VN-C205U Setup Tool and select FTP Server Displaying still images uploaded to the /user folderError recovery Connection error PasswordTransfer error Alarm FTP Upload SettingStart up the VN-C205U Setup Tool and select Time When NTP is usedStart up the VN-C205U Setup Tool and select Memory Info Normal High SpeedConnect to VN-C205 Starting Up V.Networks Controller Features that Allow Setting Using the V.Networks ControllerSelect View Specify Image Size and Upside Down settings Settings Setting Using the V.Networks ControllerMotion Detection Standby Image Size and InversionImage Quality Setting Operations Setting Using the V.Networks ControllerFrame Rate Alarm Setting Select Setting and Property Perform setting Select Setting and Time Stamp Perform settingWhen alteration is complete, click Time StampRecord/Stop Playback Operations Operation Using the V.Networks ControllerPlay button Click Playback screen is displayedSnapshot Operating Environment Access Authorization LevelSetting Using the Web Browser Operations Operating Using a Web BrowserStarting Up the Web Browser Setting Using the Web Browser 1. Other Settings Setting Using the Web Browser 2. View Setting Click to apply settings and to save the set values Setting Using the Web Browser 3. Alarm Setting Alarm  Alarm OutOperations Setting Using the Web Browser Setting Using the Web Browser 4. FTP SettingViewing Live Images Viewing Still ImagesSymptom Causes/Remedial Actions TroubleshootingImage Link Displaying a still imageOthers Specifications120 Template テンプレート