JVC VN-C205 manual Connection Examples, Preparation Procedure

Page 7

Preparation

Connection Examples

LAN Connection

VN-C205

VN-C205

LAN

PC

Preparation Procedure

Set the camera in the following procedure.

Step 1 Connection/Installation

Firstly, make a hole in the ceiling, followed by connecting the input power cable,

LAN cable or alarm signal cable to the terminal of this camera.☞Page 14 Next, attach the camera to the ceiling. Do not forget to attach the safety wire.

Step 2 Network Settings

Install the software, set the network for this camera as well as using the "VN-

Internet Connection

VN-C205

VN-C205

LANINTERNET

FTP Server

PC

PC

Updated images are automatically uploaded at a regular interval

Peer-to-Peer Connection

VN-C205

Crossover Cable

PC

12

C205U Setup Tool", and register the connected camera with the "V.Networks ☞Page 27 Controller".

●In a system where more than 1 VN-C205 is used, turn on the power for a VN-C205 first, followed by setting the camera until "2-3 Setting IP Address for this Camera Using the 'VN-C205U Setup Tool' " is completed. Upon doing so, turn on a second camera and perform setting in the same way. Perform the same procedure for

subsequent cameras. (☞Page 22)

Step 3 Setting Using the V.Networks Controller

Perform settings for Image Quality and Alarm using the "V. Networks Controller"	☞Page 56
software that has been installed.

Step 4 Operating Using the V.Networks Controller

The "V. Networks Controller" can also be used to perform recording/playback	☞Page 66
operations.

Step 5 Operating Using a Web Browser

Operation is possible via a web browser.	Page 72
	☞

13

Image 7

Contents VN-C205 VN-C205INSTRUCTIONSInformation for USA Not apply to all appliancesOperation SettingsContents Introduction Preparation SettingsOperating Precautions CharacteristicsIntroduction Operating Environment Name and Function of Parts Latest UpdatesVideo setting switch Connection Examples Preparation ProcedurePreparation Flowchart of installation work for camera Getting StartedInstallation Adjustment of the camera’s angle of viewMounting the Camera to the Ceiling Preparation Connection/InstallationPreparations Inserting the CF card Preparations Connection to Alarm Input/Output TerminalPoint the camera in the direction you wish to capture Connect the alarm terminalConnect the input power supply cable Connect the LAN cableAdjusting the iris level Settings related to video When installing the Camera to the electrical boxAdjusting the focal length Adjusting the focusPull out the cables aside and mount Installing the SoftwareWhite-spot correction Select Internet Protocol TCP/IP and click Properties Setting PCs IP Address Windows XPSettings Network Settings ClickSet IP address to Setting PCs IP Address WindowsFor Windows 2000, set according to the following procedure Select Settings and click PropertiesClick Start up the V.Networks Controller. This VN-C205U Setup Tool only allows connection of VN-C205Check settings For other settings, nextViewing of motion images only Other Settings Using the VN-C205U Setup ToolAuthorization Level Allowed Access All operations using the V.Networks ControllerOther Settings Using the VN-C205U Setup Tool 2. Multicast Perform area setting Alarm Input This section describes procedures for alarm settingOperation when an alarm input is activated Alarm FTP Alarm 1/AlarmDetect Mode Alarm OutputOutput Value Alarm Output Function/Set ValueOutput Output Set ValuesRecording time Setting the Advance screenRecording files Displaying still images uploaded to the /user folder Other Settings Using the VN-C205U Setup Tool 6. WebOther Settings Using the VN-C205U Setup Tool 7. FTP Server Start up the VN-C205U Setup Tool and select FTP ServerAlarm FTP Upload Setting PasswordError recovery Connection error Transfer errorWhen NTP is used Start up the VN-C205U Setup Tool and select TimeStart up the VN-C205U Setup Tool and select Memory Info High Speed NormalConnect to VN-C205 Starting Up V.Networks Controller Features that Allow Setting Using the V.Networks ControllerImage Size and Inversion Settings Setting Using the V.Networks ControllerSelect View Specify Image Size and Upside Down settings Motion Detection StandbyOperations Setting Using the V.Networks Controller Image Quality SettingFrame Rate Alarm Setting Time Stamp Select Setting and Time Stamp Perform settingSelect Setting and Property Perform setting When alteration is complete, clickRecord/Stop Click Playback screen is displayed Operations Operation Using the V.Networks ControllerPlayback Play buttonSnapshot Operating Environment Access Authorization LevelOperations Operating Using a Web Browser Setting Using the Web BrowserStarting Up the Web Browser Setting Using the Web Browser 1. Other Settings Setting Using the Web Browser 2. View Setting Alarm Out Setting Using the Web Browser 3. Alarm SettingClick to apply settings and to save the set values AlarmOperations Setting Using the Web Browser Setting Using the Web Browser 4. FTP SettingViewing Live Images Viewing Still ImagesDisplaying a still image TroubleshootingSymptom Causes/Remedial Actions Image LinkOthers Specifications120 Template テンプレート