AKG Acoustics PS 4000 W manual Safety and Environment, Description, Introduction Packing List

Page 12

▲! 1 Safety and Environment

1.1Safety 1. Do not spill any liquids on the equipment and do not drop any objects through the ventilation slots in the equipment.

2.The equipment may be used in dry rooms only.

3.The equipment may be opened, serviced, and repaired by authorized personnel only. the equipment contains no user-servicea - ble parts.

4.Before connecting the equipment to power, check that the AC mains voltage stated on the supplied power supply is identical to the AC mains voltage available where you will use the equipment.

5.Operate the equipment with the supplied 12 VDC power supply. Using adapters with an AC output and/or a different output volt- age may cause serious damage to the equipment.

6.If any solid object or liquid penetrates into the equipment, shut down the sound system immediately. Disconnect the power sup- ply from the power outlet immediately and have the equipment checked by AKG service personnel.

7.If you will not use the equipment for a long period of time, disconnect the power supply from the power outlet. Please note that the equipment will not be fully isolated from power when you set the power switch to OFF.

8.Do not place the equipment near heat sources such as radiators, heating ducts, or amplifiers, etc. and do not expose it to direct sunlight, excessive dust, moisture, rain, mechanical vibrations, or shock.

9.To avoid hum or interference, route all audio lines, particularly those connected to the microphone inputs, away from power lines of any type. If you use cable ducts, be sure to use separate ducts for the audio lines.

10.Clean the equipment with a moistened (not wet) cloth only. Be sure to disconnect the power supply from the power outlet before cleaning the equipment! Never use caustic or scouring cleaners or cleaning agents containing alcohol or solvents since these may damage the enamel and plastic parts.

11.Use the equipment for the applications described in this manual only. AKG cannot accept any liability for damages resulting from improper handling or misuse.

1.2Environment 1. The power supply will draw a small amount of current even when the equipment is switched off. To save energy, disconnect the power supply from the power outlet if you will leave the equipment unused for a long period of time.

2.When scrapping the equipment, separate the case, circuit boards, and cables, and dispose of all components in accordance with local waste disposal rules.

3.The packaging of the equipment is recyclabe. Dispose of the packaging in an appropriate container provided by the local waste collection/recycling entity and observe all local legislation relating to waste disposal and recycling.

2 Description

2.1Introduction

2.2Packing List

Thank you for purchasing an AKG product. This Manual contains important instructions for setting up and operating your equipment. Please take a few minutes to read the instructions below carefullybefore operating the equipment. Please keep the Manual for future reference. Have fun and impress your audience!

1 PS 4000 W antenna splitter

1 rack mount kit

Check that the packaging contains all of the components listed above. Should anything be missing, please contact your AKG dealer.

2.3 Optional Accessories

•Power supplies:

12 V DC/500 mA for distributed powering only

12 V DC/≥1,4 A for two receivers

•SRA 2 B/W active directional antenna SRA 2 W passive directional antenna

•RA 4000 B/W active omnidirectional antenna

RA 4000 W passive omnidirectional antenna

•Antenna cables: MK PS: 2 ft. (60 cm) MKA 5: 15 ft. (5 m) MKA 20: 66 ft. (20 m)

•PSU 4000 central power supply

•ASU 4000 remote power adapter

• AB 4000 antenna booster

12

PS 4000 W

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Please read the manual before using the equipment Prima di utilizzare l’apparecchio, leggere il manualeFavor leia este manual antes de usar o equipamento Inhaltsverzeichnis Sicherheit und UmweltBeschreibung Anmerkung SRA 2 B/W 2 RA 4000 B/WSiehe Tabelle 1 auf Seite Inbetriebnahme Antennen anschließen Antenne RG58 0 13 m / RG213 5 26 m13 m / RG213 5 26 m Siehe Fig WichtigDies nicht gewährleistet CLA-SchalterDer Kabellänge ab Bringen Sie die Abdeckung wieder anRG213 111 121 100105 115 100 110Betriebshinweise ReinigungFehlerbehebung Lungs diagramme Technische DatenSplitter leuchtet auf Kabellängen zu niedrigTable of Contents Safety and Environment DescriptionIntroduction Packing List PS 4000 W antenna splitterError LED be lit instead Supply voltage for active componentsDisconnect an antenna cable Ed receiversGetting Started Stands FloorBoom because this may degrade the reception quality Connect an antenna cable to each antennaRemove the cover of the CLA switch bank Replace the coverMultichannel Systems with PS 4000 W Antenna Splitters Refer to on14 dB 12 dB 10 dB Cleaning TroubleshootingOperating Notes Specifications RA 4000 B/W Omnidirectional Booster AntennaTable des matières Sécurité et environnementNous vous remercions d’avoir choisi un produit AKG Splitter d’antenne PS 4000 WDC/≥1,4 a pour 2 récepteurs ConsidéréFace arrière Face arrière du PS 4000 WMise en service Voir FigChe de l’autre splitter Minima suivantesInstallation monocanal avec antennes passives Installations multicanaux avec splitter d’antenne PS 4000 WVoir Tableau 1, page 26 et Fig Branchez un câble d’antenne sur chaque antenneRespondants PSU 4000 pour trois splitters et quatre récepteursVia le câble d’antenne Également alimenter trois composants actifsGamme I + SRA 2 B/W Instructions pour le fonctionnement NettoyageCaractéristiques techniques Antenne amplifiée omnidirectionnelle RA 4000 B/WIndice Sicurezza ed ambiente’apparecchio deve venir impiegato solo in vani asciutti Sponde alla tensione di rete del luogo d’impiegoVo LED OK si spegne e il LED rosso Error si accende DescrizionePannello frontale NotaLato posteriore Vamente un alimentatore a distanza ASU SRA 2 B/WAlimentatore centrale PSU Messa in esercizio Montaggio su parete/soffitto2Montaggio su supporto da pavimento Antenna RG58 0 13 m / RG213 5 26 m 46 m / RG213 12 97 mVedi tabella 1 a pagina 35 e fig Inserite in ogni antenna un cavo d’antennaNo questo passaggio Togliete la copertura dell’interruttore CLARimontate la copertura Gamma I + SRA 2 B/W Errori e rimedi Indicazioni per l’esercizioPulizia Splitter d’antenna PS 4000 W Antenna onnidirezionale con booster RA 4000 B/WSeguridad y medio ambiente Corriente pueden dañar seriamente el aparatoCio de atención al cliente Descripción Parte posterior Parte posterior del PS 4000 WPuesta en funcionamiento Antena RG58 0 13 m / RG213 5 26 m Ver Fig ¡ImportanteSistema monocanal con antenas activas 5Sistemas multicanal con divisor de antenas PS 4000 WOtros fabricantes no garantizan esto Conmutador CLAEl tipo de antena, el tipo de cable y la longitud de cable Vuelva a colocar la tapaGama I + SRA 2 B/W Solución de errores LimpiezaDatos técnicos Emite luzCable son muy grandes La tensión de alimentación de los componentes deÍndice SegurançaApresentação MK PS 60 cmAntena direcional passiva SRA 2 W Alimentador remoto ASULado traseiro 2 RA 4000 B/WOperação Veja tabela 1 na página 53 e fig Veja fig ImportanteSistema monocanal com antenas ativas Isto não é garantido Bandas I + SRA 2 B/W Resolver problemas Dicas para a operaçãoLimpeza Especificações PS 4000 W PS 4000 W RA 4000 B/W PS 4000 W 4x SR RA 4000 B/ W PSU PS 4000 W/1 PS 4000 W/2 PS 4000 W/3ZAPD-21 OutASU 01/10/9100 U 12
Top Page Image Contents