Tunturi C80 HRC Interval Program, Target HR Program, Memory Function, Saving the Programs

Page 8

O W N E R ' S M A N U A L • C 8 0

P4. Uphill effort profile for the improvement of endurance fitness. Peaks are relatively longlasting, increasing in intensity until the closing phase of the profile. This profile is specifically suitable for the physically fit. With default setting, max. resistance value is 29 Nm, average resistance value is 19 Nm.

HRC INTERVAL PROGRAM

The HRC INTERVAL program enables training at the varying, requested pulse level. The program requires measurement of heart rate.

1.Select the HRC INTERVAL program by pressing HRC after the meter has been switched on or after pressing RESET. The various target HR levels are indicated by dots on the display. By pressing the HRC key repeatedly you get the display to show different profiles (P1 - P4) and you can choose the one best suited for you by pressing ENTER.

2. The TIME display will start to flash. Choose the desired duration of workout by using the arrow keys (10-180 minutes in steps of 5 minutes, default 20 minutes). Press ENTER. The device uses this value to calculate the duration of the different effort levels during the program.

3. The Total Counts display starts to flash. The display reads KG _. Enter your weight by using the arrow keys (default value 70 kg). Press ENTER.

4. Begin your workout. If the pedaling effort seems too strenuous or easy, change the preset pulse value (default

100%) by using the arrow keys. The columns in the display show the present target HR level.

Follow your heart rate during the training and especially the heart indicator. The HR light should flash in

time with your heartbeat. If the indicator begins to function in a disturbing fashion (e.g. additional beats or abnormal fluctuations), the pulse measurement is not functioning properly. Stop your workout at once and make sure that you have followed all the instructions described in this manual about heart rate measurement.

Edited programs can be saved in the memory of the meter.

Profile figures are at the back of the manual.

P1. 3-peak heart rate profile for the improvement of oxygen uptake capacity. With relatively longlasting peaks, this profile is suitable for beginners. With default setting, max. HR value is 125, average HR is 112.

P2. Uphill heart rate profile where the heart rate increases steadily until the midpoint of the profile, steadily decreasing thereafter. This profile is suitable for beginners. With default setting, max. HR value is 150, average HR is 121.

P3. 3-peak heart rate profile for the improvement of endurance fitness. Peaks are relatively longlasting, but the heart rate level remains fairly constant throughout. This profile is suitable for all fitness levels. With default setting, max. HR value is 140, average HR is 120.

P4. 3-peak heart rate profile for the improvement of oxygen uptake capacity. Peaks are relatively longlasting, with each followed by a steady recovery period. This profile is specifically suitable for the physically fit. With default setting, max. HR value is 160, average HR is 133.

TARGET HR PROGRAM

The TARGET HR program enables training at the requested heart rate level. The program requires measurement of heart rate.

1.Select the TARGET HR program by pressing TARGET HR after the meter has been switched on or after pressing RESET.

2. The HR display will start to flash. Set the desired heart rate value (default 110 bpm) by using the arrow keys. Press ENTER. NOTE! The preset value can be changed during the training.

3. The TIME display will start to flash. Choose the desired duration of workout by using the arrow keys (10-90 minutes in steps of 5 minutes). Press ENTER. The equipment uses this value to calculate the duration of the different effort levels during the program.

4. The Total Counts display starts to flash. The display reads KG _. Enter your weight using the arrow keys (default value 70 kg). Press ENTER.

5. Begin your workout. If the set heart rate value seems too strenuous or easy, change the heart rate value by using the arrow keys. The columns in the display show the present heart rate level.

Programs can be saved in the memory of the meter.

MEMORY FUNCTION

The meter enables saving of 8 manually made programs to its memory. NOTE! The programs are saved in constant resistance mode (faster pedaling means an increase in effort).

SAVING THE PROGRAMS

When you wish to save a program in the memory of the meter, press the MEMORY key after your workout session. The display reads P1. Choose the desired memory location (P1-8) by using the arrow keys or MEMORY key repeatedly. Press ENTER. Your program is now saved in the memory of the meter. NOTE! A total of 32 changes can be saved in each program.

RUNNING THE PROGRAMS

1.When you want to use an earlier saved program, press the MEMORY key after the meter has been switched on or after pressing RESET.

2. Choose the desired program with the MEMORY key or arrow keys. Press ENTER.

3. The time display will start to flash. Choose the desired duration of workout by using the arrow

keys (10-180 minutes in steps of 5 minutes, default: last saved time). Press ENTER.

4. The total counts display starts to flash. The display reads KG _. Enter your weight using the arrow keys.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Betriebsanleitung Mode Demploi Handleiding Manuale Duso Manual DEL UsuarioBruksanvisning KäyttöohjeContents Assembly Before assembling the device, insure all parts are presentRear frame Welcome to the World Tunturi ExercisingPedal Cranks Front FrameHandles Console Power Cord Exercising Press for 2 seconds, Resets all values ConsoleTempo strengthens correspondingly your back and hips 60-70 % of maximum heart-rateOperating the Console Saves and recalls manual programs PBegin your workout Programs can be saved in the memory of the meterHRC Interval Program Target HR ProgramMemory Function Saving the ProgramsMaintenance Technical SpecificationsTransport and Storage Wichtige SicherheitshinweiseMontage Prüfen Sie, dass folgende Teile vorhanden sindHinterer Rahmen Herzlich Willkommen in DER Welt DES Trainierens MIT TunturiEntfernen Sie den Halter vom Achsenende Vorderes FussrohrVorderer Rahmen HandgriffeNetzkabel PedalschäfteCockpit Trainieren MIT Tunturi Das Maximum unterscheidet sich von Mensch zuHerzfrequenz HerzfrequenzbereicheCockpit Betrieb DES CockpitsFortgeschrittene 60-70 % der maximalen Herzfrequenz Zum Zurücksetzen der Werte 2 Sekunden drückenRolling Hills HRC Interval ProgrammAnwendernummer wählen P1 bis P8 und mit der Das Training beginnenWartung Transport UND LagerungTechnische Daten Conseils ETPortez des vêtements et chaussures appropriés Conseils ET Avertissements’appareil ne doit pas être utilisé à l’exterieur Assemblage Châssis arrièrePied D’APPUI Avant Châssis AvantCordon D’ALIMENTATION Montants DES PédalesCompteur Exercice Rythme CardiaqueUnite DES Compteurs Fonctions Il est possible de mettre en mémoire le programme effectué Utilisation DE L’UNITE DES CompteursCommencez l’exercice Programme Target HR Pouls Constant Memoire MemoryMise EN Memoire DES Programmes Sortie DES Programmes MIS EN MemoireDefauts DE Fonctionnement Transport ET RangementCaracteristiques Techniques Opmerkingen EN Adviezen GezondheidDE Trainingsruimte HET Gebruik VAN DE TrainerAchterframe DE MontageControleer of de verpakking alle onderdelen bevat Het apparaat mag alleen worden aangesloten op een TreeplankenMonitor ElektriciteitssnoerConditietrainen Trainen OM AftevallenHartslagmeting Trainings NiveauMonitor FunctiesDit venster geeft het aantal bewegingen of snelheid weer Functies VAN DE ToetsenHRC Interval Programma Manual ProgrammaRolling Hills Programma Onderhoud Lengte 197 cm Breedte 66 cm Hoogte 169 cm Gewicht 105 kg VerplaatsenTechnische Gegevens Telaio posteriore AvvertenzeMontaggio Manubri Piede D’APPOGGIO AnterioreTelaio Anteriore Allenamento Barre DEI PedaliPannello Cavo PER LA CorrenteBattito Cardiaco Misurazione Della Frequenza Cardiaca CON LA CinturaMisurazione Delle Pulsazioni CON Sensori NEL Manubrio Aree DI PulsazioniPannello USO DEL Pannello ElettronicoAzzera tutti i valori premendo 2 secondi Conferma i valori ed i parametri impostati dall’atenteProgramma HRC Interval Programma a Pulsazione Costante Target HRManutenzione Trasporto E ImmagazzinaggioDati Tecnici Lunghezza 197 cmInformacion Y Precauciones MontajeCompruebe si en los embalajes están todas las piezas Armazón traseroEmpuñaduras DEL Manillar Pata Delantera DE SoporteArmazon Delantero Ejercicio Vastagos DE LOS PedalesContador Cable DE AlimentaciónContador Sobre todo para fortalecer su espalda y caderasRitmo Cardíacoco Teclas Y FuncionesFuncionamiento DEL Contador Electronico Pone a cero todos los valoresConfirma los valores y parámetros programados Salva y recupera los valores programados por usted P1- P8Programa HRC Interval Programa Target HR Pulso ProgramadoMantenimiento Transporte Y AlmacenamientoDatos Tecnicos Longitud 197 cmBruksanvisning MonteringBörja med att packa upp och kolla att du har följande delar Bakre stommenFrämre Stombenet Främre StommenHandtagen PedalvevarnaElkabeln TräningMätaren Mätare Nollställning av värden, tryck på knappen för 2 sekunderPuls PulsområdenAnvändning AV Mätaren Sparande och öppnande av egna program P1 P8Displayen anger turvis tiden och uteffekten i watt Enheten kg / LB kan väljas med en omkopplar bakom mätarenDu kan börja träna. Genom tryck på pilknapparna Underhåll Transport OCH FörvaringTekniska Data Störningar VID AnvändningHuomautukset JA Varoitukset AsennusLaitteen ehdoton enimmäiskäyttäjäpaino on 150 kg TakarunkoEtutukijalka EturunkoKäsikahvat PoljinvarretVerkkojohto HarjoitteluMittari Mittari MaksimisykkeestäSyke SykealueetMittarin Käyttö Arvojen nollaus painamalla näppäintä 2 sekunnin ajanNäyttö ilmoittaa vuorotellen aikaa ja tehoa watteina PäältäHRC Interval -OHJELMA Target HR VakiosykeohjelmaMuistitoiminto Memory Ohjelmien TallentaminenHuolto Kuljetus JA SäilytysMitat Tallennettujen Ohjelmien KäyttöG28 C80 Profiles Page Page Page 5837016 B
Top Page Image Contents