Weider 831.14623.0 user manual Part Identification CHART-Model No .14623.0 R0606A

Page 5

PART IDENTIFICATION CHART—Model No. 831.14623.0 R0606A

Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST on pages 39 and 40. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. If a part is missing, call toll-free1-877-992-5999.

M8 Nylon	M10 Nylon		M4 Washer
		M12 Nut (112)	(104)	M6 Washer
Locknut (78)	Locknut (77)			(114)

M8 Washer (103)

M10 Washer (80)	M10 Large Washer (105)	M12 Large Washer (98)

M4 x 12mm

M4 x 16mm

M6 x 16mm

M10 x 75mm Button Screw (118)

Self-tapping

Self-tapping

Screw (88)

Screw (102)

Screw (110)

M8 x 22mm	M10 x 100mm Bolt (140)
Shoulder Bolt (90)

5

Image 5

Contents Sears, Roebuck and Co., Hoffman Estates, IL Model No Serial NoTable of Contents Important Precautions Left Side Before YOU BeginRight Side Part Identification CHART-Model No .14623.0 R0606A Part Identification CHART-Model No .14623.0 R0606A Make Assembly Easier for Yourself AssemblyBox on page 7. See the Part Identifi Frame AssemblyLocknut, the Foot Plate must pivot Freely Do not Tighten the Nylon Locknuts yetTighten the Nylon Locknuts yet Manner. Do not tighten the M10 Nylon Locknut yet Locknuts 78. Do not Tighten the Nylon Locknuts yetLocknut 77. Do not tighten the Nylon Locknut yet Locknuts 77. Do not tighten the Nylon Locknuts yet En the Nylon Locknuts yet104 110 103 100 101 120 122 119 Arm Assembly Nylon Locknut the Military Press Arm Must pivot freelyLocknut 77. Make sure the bushing is on Locknuts 77 the Leg Press Frames must Pivot freelyShown Bend See the right inset drawing. Insert the LockRepeat this step for the Left Press Arm not Identify the Butterfly Cable 50. Grease an Cable AssemblyFlat edge of the Cable is against the Butterfly Bracket Locknut 77. Make sure the Half Guards are Oriented as shownIdentify the Lat Cable 49. Route the Cable Cable Trap and Half Guards are oriented as Shown Make sure the Cable Trap is oriented as Shown Identify the Press Cable 133. AttachEdge of the Cable is against the Left Frame Identify the Leg Lever Cable 51. Route Make sure the Half Guards are oriented as ShownLocknut Guards are oriented as shown Locknut 77. Make sure the Half Guards are Oriented as shown Repeat this step for the Left Backrest Frame Not shown Seat AssemblyPasses through one of the holes in the Right Seat Frame Frame. Make sure the Adjustment KnobRepeat this step for the Left Butterfly Pad Repeat this step for the other Pad Tube Front LegMay be necessary to loosen the M10 Nylon Page Attaching the Accessories AdjustmentsChanging the Weight Setting Adjusting the Backrest Using the Curl PADLocking the Weight Stack Pad to use the press armsLocking the LEG Lever Lbs Weight Resistance ChartCable Diagram Leg Lever Cable Tightening the Cables MaintenanceExercise Guidelines Staying Motivated Muscle ChartCooling Down Date Exercise Weight Sets RepsAerobic Exercise Thursday Aerobic Exercise DateMonday Key Qty Description Part LIST-Model No111 Exploded DRAWING-Model No R0606A Exploded DRAWING-Model No Get it fixed, at your home or ours DAY Full Warranty