Whirlpool W10054070A manual Stopping,PausingorRestarting, DryingandCycleTips, StatusLights

Page 18

Adjust Dryness.

NOTE: Dryness selections can be made only while using Automatic Cycles.

How the AccelerCare™ Drying System Works

Moisture-sensing strips inside the dryer drum and temperature sensors in the airstream monitor how fast the load is drying, how hot the air should be and when clothes are dry. The system automatically stops the cycle to help save time and avoid overdrying.

To use a Timed Cycle

Turn knob to desired Timed Cycle.

Press the TIME ADJUST up or down arrows until the desired drying time is displayed. Press the up or down arrows and the time will change by 1-minute intervals. Press and hold the up or down arrows and the time will change by 5-minute intervals.

NOTE: The Time Adjust features can be used only with Timed Cycles.

Press TEMP until the desired temperature illuminates.

NOTE: The Temp feature can be used only with Timed Cycles.

NOTE: During a Timed Cycle, you can change the settings for Time, Temp, the WRINKLE SHIELD™ setting and the End of Cycle Signal.

5.(OPTIONAL STEP) If desired, select OPTIONS. For more details, see “Options.”

6.(OPTIONAL STEP) If desired, press END OF CYCLE SIGNAL. A signal will sound to alert you when a cycle ends. For more details, see “End of Cycle Signal.”

7.Press START. Be sure the door is closed.

If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

If you wish to end your drying cycle after pressing Start, press PAUSE/CANCEL twice.

Stopping,PausingorRestarting

To stop or pause your dryer at any time

Open the door or press PAUSE/CANCEL once. Press PAUSE/ CANCEL twice to cancel a cycle.

To restart the dryer

Close the door. Press START until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

DryingandCycleTips

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Timed Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

Follow care label directions when they are available.

If desired, add a fabric softener sheet. Follow package instructions.

To reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is especially important for permanent press, knits and synthetic fabrics.

Avoid drying heavy work clothes together with lighter fabrics. This could cause overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.

Cycle tips

Dry most loads using the preset cycle settings.

Refer to the Automatic or Timed Preset Cycle Settings chart (in the “Cycles” section) for a guide to drying various loads.

Drying temperature and dryness level are preset when you choose an Automatic Cycle. You can select a different dryness level, depending on your load, by pressing Dryness and choosing More, Normal, Less or Damp.

NOTE: You cannot use the Time Adjust and you cannot choose a Temperature with the Automatic Cycles.

If you wish to adjust the cycle length of a Timed Cycle, press the Time Adjust up or down arrows. Adjust the temperature of a Timed Cycle by pressing Temp until the desired temperature is selected.

NOTE: You cannot choose a dryness level with Timed Cycles.

StatusLights

Follow the progress of your dryer with the drying Status indicator lights.

Sensing

In an Automatic Cycle, the Sensing light illuminates until a wet item is detected.

In a Timed Cycle, the Sensing light illuminates at the beginning of a cycle and turns off 5 minutes into the cycle.

Wet

The Wet light illuminates at the beginning of an Automatic Cycle if a wet item is detected.

In an Automatic Cycle, if a wet item is not detected after approximately 5 minutes, the dryer goes directly into Cool Down and the Cool Down and the WRINKLE SHIELD™ setting indicators illuminate, if selected.

In a Timed Cycle, wet items are not detected. The dryer will continue to run for the length of time selected, and the Wet light will illuminate. The damp light will not illuminate.

18

Image 18
Contents Guided’utilisationetd’entretien W10054070ATable of Contents ÍndiceDryer Safety Your safety and the safety of others are very importantInstallation Instructions ToolsandPartsLocationRequirements Electrical Requirements-U.S.A.Only Mobile home Additional installation requirementsMobile home installations require It is your responsibilityIf connecting by direct wire ElectricalRequirements-CanadaOnlyStyle 1 Power supply cord strain relief Power Supply Cord Direct WireInstall strain relief ElectricalConnection-U.S.A.OnlyWire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct Wire Remove center silver-colored terminal block screwBDE CG F Optional 3-wire connection If using an existing vent system VentingRequirementsIf this is a new vent system Vent material PlanVentSystem Alternate installations for close clearancesSpecial provisions for mobile home installations Determine vent pathVent system chart Install VentSystemInstall LevelingLegs ConnectVentReverseDoorSwing Remove the door assemblyReinstall the door Reverse the strikeCanada CompleteInstallationU.S.A If the dryer will not start, check the followingStartingYourDryer Press PAUSE/CANCELDryer USE To use an Automatic CycleStopping,PausingorRestarting DryingandCycleTipsStatusLights Cycles Modifiers Options Endof CycleSignal DryingRackOptionChangingCycles,Modifiers andOptions CleaningtheLintScreen CleaningtheDryer LocationCleaningtheDryerInterior Dryer CareChangingtheDrumLight TroubleshootingVacationandMovingCare DryerOperationDryerResults Dryer displaying code messageAssistance or Service TheU.S.AInCanada Whirlpool Corporation Major Appliance Warranty CallPage Seguridad DE LA Secadora Su seguridad y la seguridad de los demás es muy importanteInstrucciones DE Instalación HerramientasypiezasRequisitos deubicación Espacios de instalación Dimensiones de la secadoraRequisitos eléctricos -Sóloen EE.UU Usted es responsable deSi el contacto de pared luce como éste Conexión eléctricaSi emplea un cable de suministro eléctrico Si hace la conexión con cableado directoConexión eléctrica-SóloenEE.UU Cable de suministro eléctrico Cable directoInstale el protector de cables Alambre de 4 hilos se recomienda Conexión de 4 hilos Cable de suministro eléctricoEstilo 2 Protector de cables para cable directo Alambre de 3 hilos si no dispone de alambre de 4 hilosConexión de 4 hilos Cable directo Conexión de 3 hilos Cable de suministro eléctrico Conexión de 3 hilos Cable directo Si usa un sistema de ventilación existente RequisitosdeventilaciónConexión opcional de 3 hilos Si éste es un nuevo sistema de ventilaciónPlanificacióndelsistemadeventilación Determinación de la vía del ducto de escape Instalación del sistemadeventilaciónInstalaciones alternas para espacios limitados Cuadro del sistema de ventilaciónInstalacióndelaspatasniveladoras Conexióndel ductodeescapeNivelacióndelasecadora Abra la puerta de la secadora Cómo invertirel cierredelapuertaCómo quitar el ensamblaje de la puerta Cómo invertir el topeCompletelainstalación-EE.UU Si la secadora no funciona, revise lo siguienteUSO DE LA Secadora PuestaenmarchadelasecadoraPara usar un ciclo automático Para reanudar la marcha de la secadora Para hacer cambios durante un ciclo automáticoCómo detener,pausaryvolveraponeren marcha Cómo funciona el sistema de secado AccelerCareSugerenciasdeciclosy secado LucesdeestadoCiclos Modificadores OpcionesSeñal defin deciclo EndofCycleSignal Cambiodeciclos,modificadores yopcionesOpción deestantedesecado Limpiezadel filtrodepelusa Cuidado DE LA SecadoraLimpiezadellugardondeestálasecadora Limpieza de cada cargaCambiodelaluz del tambor Limpiezadel interiordelasecadoraEliminacióndepelusaacumulada CuidadodurantelasvacacionesymudanzasSolución DE Problemas FuncionamientodelasecadoraResultadosdelasecadora ¿Está el filtro de pelusa obstruido con pelusa?¿Está la secadora ubicada en un armario? Ayuda O Servicio Técnico Whirlpool Corporation En EE.UU., llame al 1-800-253-1301. En Canadá, llame alSécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteInstructions D’INSTALLATION Exigences d’emplacementOutillageetpièces Spécifications électriques-PourleCanada Seulement Dimensions de la sécheuseLinstallation dans une maison mobile exige Dégagements de séparation à respecterConduit métallique rigide ExigencesconcernantlévacuationEn cas dutilisation du système dévacuation existant Conduit métallique flexibleBrides de serrage Les styles de clapets recommandés sont illustrés ci-dessousPlanification dusystèmed’évacuation ÉvacuationDéterminer litinéraire dacheminement du conduit Une réduction de la longévité de la sécheuseTableau des systèmes dévacuation Raccordementduconduitd’évacuation Installation dusystèmed’évacuationInstallation despiedsderéglagedel’aplomb Réglagedelaplomb dela sécheuseDépose de la porte Réinstallation de la porteInversiondusensdouverturedelaporte Inversion de la gâcheAcheverlinstallation Fermer la porte vérifier l’engagement de la gâcheSi la sécheuse ne démarre pas, vérifier ce qui suit Utilisation DE LA Sécheuse MiseenmarchedelasécheuseUtilisation dun programme automatique Pour mettre la sécheuse en pause ou larrêter à tout moment Arrêt,pauseouremiseenmarcheConseils pourleséchageetles programmes Pour remettre la sécheuse en marcheTémoins lumineux ProgrammesModificateurs Signaldefin deprogramme Modification des préréglages de niveau de séchage OptiondegrilledeséchageChangement des programmes après avoir appuyé sur Start Utilisation de la grille de séchageNettoyagedelemplacementdelasécheuse NettoyagedufiltreàcharpieNettoyage avant chaque charge Déménagement Nettoyagedel’intérieurdelasécheuseRetraitdelacharpieaccumulée Changementdel’ampouled’éclairage Du tambourDépannage Fonctionnementdela sécheuseLe filtre à charpie est-il obstrué de charpie? La sécheuse est-elle installée dans un placard?Résultats delasécheuse Le conduit dévacuation a-t-il la longueur appropriée?Taches sur la charge ou sur le tambour Temps de programme trop courtCharpie sur la charge Charges avec faux plisPour plus d’assistance Assistance OU ServiceSi vous avez besoin de pièces de rechange Pour trouver des pièces de rechange FSP dans votre régionGarantie DES Gros Appareils Ménagers Whirlpool Corporation Composer le 1-800-253-1301. Au Canada, composer leW10054070A