Troubleshooting
Your washing machine could fail to work |
| . |
|
|
|
|
| . | |
Before calling for Assistance (see page 12), make sure the problem |
| ||||||||
|
| o |
|
|
|
| o | ||
can't easily be solved by consulting the.following list. |
|
| . |
| |||||
| r |
|
|
|
|
| r |
|
|
Problem | . | Possible causes/Solution: | . |
|
| ||||
s | s |
|
| ||||||
|
|
|
|
|
|
|
| ||
The washing machine won't |
| • | The appliance is not plugged into the socket, or not enough to |
|
| ||||
start. |
|
| make contact. |
|
|
|
|
| |
The wash cycle won'tprahastart. |
| • | There has been a power failure. |
|
|
| |||
| • | The appliance Lid is not shut properly. TheprahaLid locked Led flashes. | |||||||
|
| • | The | button has not been pressed. |
|
|
| ||
|
| • | The START/RESET button has not been pressed. |
|
|
| |||
|
| • | The water tap is not turned | n. |
|
|
| ||
The washing machine fails to | • | The water inlet hose is not connected to the tap. |
|
|
| ||||
load water. |
| • | The hose is bent. |
|
|
|
|
| |
mikosoft |
| • | The water tap is not turned on. |
|
|
| |||
| • |
|
| mikosoft |
|
|
| ||
|
| There is a water shortage. |
|
|
|
|
•The water pressure is insufficient.
•The START/RESET button has not been pressed.
The washing machine |
| • | The drain hose is not fitted between 65 and 100 cm from the floor | ||||
continuously loads and unloads |
| (see page 3). |
|
|
| ||
water. |
|
| • | The free end of the hose is underwater (see page 3). |
|
|
|
|
|
| • | The wall drainage system doesn't have a breather pipe. |
|
|
|
|
|
| If the problem persists even after these checks, turn off the water tap, |
|
| ||
|
|
| switch the appliance off and call for Assistance. If the dwelling is on one of | ||||
|
|
| the upper floors of a building, there may be drain trap problems causing the | ||||
|
|
| washing machine to load and unload water continuously. In order to avoid | ||||
|
|
| such an inconvenience, special | ||||
The washing machine does not | • | The programme does not foresee the draining: some programmes | |||||
drain or spin. |
|
|
| require enabling the draining manually (see page 6). |
|
|
|
|
|
| • | The Easy iron option is enabled: to complete the programme, press | |||
|
|
|
| the START/RESET button (see page 7). |
|
| . |
|
|
| • | . |
|
| |
|
|
| The drain hose is bent (see page 3). |
| o | ||
|
|
| o |
| |||
|
| .• | The drain duct is clogged. | . |
| ||
|
| r |
|
| r |
|
|
|
| . |
|
| . |
|
|
The washing machine vibrates | • | When the machine is installed, the locking screws for the o | cillating |
| |||
|
| s |
| s |
|
| |
too much during the spin cycle. |
| assembly are still in place. Remove the screws (see p ge 2). |
|
| |||
|
|
| • | The washing machine is not level (see page 2). |
|
|
|
|
|
| • | The washing machine is closed in between furniture cabinets and |
| ||
|
|
|
| the wall (see page 2). |
|
|
|
The washing machine leaks. |
| • | The water inlet hose is not screwed on correctly (see page 2). |
|
| ||
| praha |
| • | The detergent dispenser is obstructed ( o cleanprahait, see page 10). |
| ||
|
|
| • | The drain hose is not secured properly (see page 3). |
|
|
|
The |
| • | Switch off the machine and unplug the appliance; wait for |
|
|
| |
flashes rapidly at the same time |
| approximately 1 minute then switch it on again. |
|
|
| ||
as at least one other LED. |
|
| If the problem persists, contact Assistance. |
|
|
| |
|
|
|
|
|
|
| |
There is too much foam. |
| • | The detergent is not suitable for machine washing (it should bear |
|
| ||
mikosoft |
|
|
|
| |||
|
|
| mikosoft |
|
|
| |
|
|
|
| the definition "for washing machines" or "hand and machine wash", | |||
|
|
|
| or the like). |
|
|
|
|
|
| • | You used too much detergent. |
|
|
|
GB
Installation Description Programmes Detergents Precautions
Care Troubleshooting Service
11