Gateway 312785C ProMix 2KS Modbus/TCP Variable Map EasyKey, Units Low Limit High Limit

Page 30

Modbus and I/O Data

ProMix 2KS Modbus/TCP Variable Map

Table 4: ProMix 2KS Modbus/TCP Variable Map

	EasyKey
* Read/Write	Modbus
Status	Register	Description	Size	Units	Low Limit	High Limit

Read Only	40003	Current flow rate	16 Bit	cc/min	0	5000
Read Only	40004	Actual ratio	16 Bit	none	0	9999
Read Only	40005	Active recipe	16 Bit	none	0	60
Read Only	40006	Potlife 1 remaining	16 Bit	sec	0	9999
Read/Write	40007	Job complete	16 Bit	none	0	0xFFFF
Read/Write	40008	Reset job total	16 Bit	none	0	9
Read Only	40009	Potlife 2 remaining	16 Bit	sec	0	9999
Read Only	40010	Active fault	32 Bit	none	0	0xffffffff
Read Only	40032	Control version	32 Bit	none	0	0xffffffff
Read/Write	40040	Robot digital input	16 Bit	none	0x0000	0xFFFF
Read Only	40041	Robot digital output	16 Bit	none	0x0000	0xFFFF
Read/Write	40046	New recipe	16 Bit	none	0	60
Read Only	40048	Current fluid pressure	16 Bit	psi	0	5000
Read Only	40049	V/P percent output	16 Bit	%	0	100
Read Only	**40056	Actual ratio reducer	16 Bit	none	0	9999
Read Only	40114	Flow control option	16 Bit	0=proportioning only	0	4
				1=1K flow control
				(future)
				2=2K flow control
				3=pressure override
				4=manual percent
				override
Read/Write	40115	Flow setpoint data source	16 Bit	0=discrete	0	1
				1=network
Read/Write	40120	Manual override percent	16 Bit	%	0	100
		opening
Read/Write	40125	Flow control range	16 Bit	0=0-300 cc/min	0	2
				1=0-600 cc/min
				2=0-1200 cc/min
Read/Write	40126	Flow control tolerance	16 Bit	%	0	99
Read/Write	40127	Flow control proportional	16 Bit	default=400	0	9999
		gain Kp
Read/Write	40128	Flow control integral gain	16 Bit	default=40	0	9999
		Ki
Read/Write	40129	Flow control alarm time	16 Bit	sec	0	99
Read/Write	40137	Flow control setpoint	16 Bit	cc/min	0	1200
Read/Write	43123	Flow control override	16 Bit	0=off (normal)	0	2
		mode		1=% open
				2=pressure mode
Read/Write	43141	Flow control enable	16 Bit	0=off	0	1
				1=on

*This column represents the rule that must be implemented by automation. Writing to Read Only registers must be avoided.

**For ProMix 3KS Systems only.

30

312785C

Image 30

Contents Important Safety Instructions Gateway Network Communication KitsContents Graco Gateway Kits Related ManualsComponent Manuals in English Description Fire and Explosion Hazard Location Install the Gateway Module HardwareGraco Gateway Overview MountingNON-HAZARDOUS Area Connect the Module to EasyKey Cabling ConnectionsGateway Module Wiring Diagrams onEasyKey Bottom View IG EasyKey and Module Cable Connection PointsPower Connector Expansion Port RS232/PGUSB/PG Ethernet Install CompactFlash Card Mount the Control on DIN RailInstall the GracoConfig Software System RequirementsSoftware Updates Load the SoftwareDownload the Preconfigured Database to the Gateway Module Set Communications Port to USBCommunications Button Graco Gateway Network Communications ConfigurationStartup GracoConfig Main Balloon HelpSetup the Database Preconfigured DatabaseRename PLC1 Map Data Mapping Gateway BlocksSetting Block Size Block Mapping Data Stop Mix Process Modbus and I/O DataStart Mix Process Color Change ProcessStart Mix Mode Process Flow Chart Mixing Mode Process Flow Chart Purge Mode Process Flow Chart Color Change Mode Process Flow Chart Alarm Processing Alarm Processing Flow ChartModbus and I/O Data ProMix 2KS Active Alarms Modbus Register ProMix 2KS Digital Outputs Modbus RegisterBit Digital Input Binary Name Details ProMix 2KS Active Alarms Modbus Register Modbus Status Register Description ProMix 2KS Modbus/TCP Variable MapProMix 2KS Modbus/TCP Variable Map EasyKey Units Low Limit High LimitProMix 2KS Recipe Bits ProMix 2KS Recipe BitsTroubleshooting General TroubleshootingCommunication Troubleshooting See Serial Communication TrouBleshooting page 36 or Ethernet Problem Cause Solution Graco Gateway Messages Troubleshooting Serial Communication Troubleshooting Ethernet Communication Troubleshooting User Communication Ports TX/RX LEDs LED FunctionsStatus STS LED Ethernet LEDsSystem Electrical Schematic Non-Hazardous AreaParts Part No. Description QtyWiring Diagrams 417Introduction Appendix a DeviceNet Slave CommunicationOverview DeviceNet Port ProtocolsDeviceNet Port Pin Outs and PLC Connection About DeviceNet Predefined Master/Slave Connection SetLevel of Support Gateway Configuration Configure the Gateway DeviceNet Option CardHardware Select DeviceNet Server Device Settings Create Gateway Blocks Add a Gateway BlockSelect Data Type Word as Long DeviceNet Block Mapping Automatic Update of the EDS File Automatic EDS UpdateConfigure the RSNetWorx for DeviceNet Software EDS ValidationReview EDS Registration Apply and Save Configure the Allen Bradley ControlLogix PLC Create Valid DeviceNet ScannerWire the DeviceNet Network Main Task TreeAppendix B Profibus DP Slave Communication Profibus Port ProtocolsAlso see Appendix B Profibus DP Slave Communi- cation on About Profibus DP DP MasterSetup the PLC Install the GSD fileBrowse to GSD File Setup the Profibus Network DP Properties WindowOpen Profibus Properties Set Transmission Rate Add the Graco Gateway to the Profibus Network Add Graco Gateway to Profibus NetworkConfigure Data Blocks Graco Gateway Setup Setup the Profibus CommunicationSelect Profibus Server Setup Tags Create a VariableSelect Block Type How Addressing Works PLC Addressing SchemeUseful Formulas PLCAppendix C Graco Gateway to ControlLogix via Ethernet IP Ethernet PLC ConnectionControlLogix Configuration Ethernet Module PropertiesPort Configuration Window Ethernet Module Properties Ethernet Configuration Data Graco Gateway Configuration Ethernet Block SettingsAppendix C Graco Gateway to ControlLogix via Ethernet IP Dimensions Dimensions Technical Data Graco Standard Warranty Graco Information