DCS BFG-30G, BFG-308S, BFG-308GD manual Locating BUILT-IN Clearances, General, Insulated Jacket

Page 11

INSTALLATION

LOCATING BUILT-IN CLEARANCES

WARNING!

The appliances are designed to function in an open area. Recommended minimum clearances should be maintained to all surfaces (combustible* and noncombustible**) for optimum performance. Noncombustible** material within the minimum clearance area could result in discoloration or deterioration.

*DEFINITION OF COMBUSTIBLE MATERIAL - Any materials of a building structure or decorative structure made of wood, compressed paper, plant fibers, stucco or other materials that are capable of transferring heat or being ignited and burned. Such material shall be considered combustible even though flame-proofed, fire-retardant treated, or painted surface or plastered.

**DEFINITION OF Noncombustible MATERIAL - Material which is not capable of being ignited and burned, such as materials consisting entirely of, or a combination of, steel, iron, brick, tile, concrete, slate, and plaster (which is unpainted).

Important!

It is recommended that a minimum of 10 sq. inches of ventilation opening be provided for both the left and right sides, as well as the back of enclosure (Fig. 02), in order to safely dissipate unburned gas vapors in the event of a gas supply leak.

WARNING!

Note specific built-in enclosure ventilation requirements. See text and Fig. 02.

GENERAL

The outdoor appliance is designed for easy placement into masonry enclosures. For non-combustible applica- tions the outdoor appliance drops into the opening shown in Fig. 03 and hangs from its side flanges. The deck must be level and flat. A deck is not required to support the unit from the bottom. When using the insulated jacket in a combustible enclosure application, see the bottom of Fig. 03. The jacket assembly must be supported from the bottom by a ledge on each side or a solid deck beneath the entire insulated jacket.

INSULATED JACKET:

If the outdoor appliance is to be placed into a combustible enclosure, an approved insulated jacket is required and is available from your dealer. Insulated jacket is not required for BFG-30BS Side Burner Sink Model. Use only the DCS insulated jacket (p/n #70859) which has specifically been designed and tested for this purpose.

Review the detail drawing shown (Fig. 03) and take into account the provisions shown for gas line hook-up clear- ance in the right rear corner. It is recommended that ventilation holes are provided in the enclosure to eliminate the potential build-up of gas in the event of a gas leak. The supporting ledges or deck must be level and flat. The counter should also be level.

Ventilation Requirements:

10 in.2 Min. ventilation

on the back side

10 in.2 Min. ventilation

10 in.2 Min. ventilation

left hand side

on the right hand side

 

B

1" Min.

Note: not drawn to scale

 

A

 

Opening for

 

access doors/drawers

Fig. 02

CUTOUT DIMENSIONS OF MATCHING ACCESS DOORS/DRAWERS:

ACCESS DOOR/

A

B

DRAWER MODELS

 

 

ADN 20X24

22"

20"

 

 

 

ADN 20X30

28"

20"

 

 

 

ADN 20X36

34"

20"

 

 

 

ADN 20X48

46"

20"

 

 

 

ADR24

22"

20"

 

 

 

ADR36

34"

20"

 

 

 

ADR30

28"

20"

 

 

 

ADR48

46"

20"

 

 

 

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Professional Liberty Collection Page Please Retain this Manual for Future Reference Message to OUR CustomersContents Important Safety Notice Safety Practices & PrecautionsOutdoor Appliance Placement Safety Practices & Precautions Outdoor Appliance Models BFG-30G All-Grill Before Using Your ApplianceLocation InstallationLocating Outdoor APPLIANCE/BUILT-IN Clearances Insulated Jacket Locating BUILT-IN ClearancesGeneral Standard layout for non-combustible enclosure BUILT-IN Construction DetailsLocating the Cart Cart Assembly InstructionsStep Outdoor Appliance Head Preparation Pinch Point Cover Hanger Gas Hookup LPGAS Requirement GAS HOOK-UPLP Tank Requirements LP GAS Hook UP Type 1 or QCC1 Regulator18 max LP Tank Restraint for BUILT-IN InstallationStep Before Testing Leak Testing GRILL/GRIDDLE UnitFlame Height Leak Testing Side BurnerBurner Adjustment Side Burner Burner Efficiency and Flame CharacteristicsOutdoor Appliance Burner Flame Height Burner Adjustment GRILL/GRIDDLE UnitLOW Setting Adjustment Radiant Assembly Installation Radiant AssemblySink Faucet InstallationSink Installation Side Shelf Optional accessory These Instructions Check ListUSE of the Grill Using the GrillLighting Instructions Grilling Hints Important Using the GrillMatch Lighting Using the Side BurnerUSE of the Griddle Using the GriddleBefore Using the Griddle for the First Time or To RE-SEASON ThermocoupleUsing the Griddle Using the Sink Cleaning Grill Grates Care and MaintenanceBattery Replacement Regulator and Hose ReplacementGrill Burner Grill Burner CleaningCeramic Rods Stainless SteelSide Burners Orifice CleaningSide Burner Grate Sink Side Burner ElectrodesControl Knobs Problem What to do Troubleshooting Outdoor ApplianceBefore Calling for Service Troubleshooting Side Burner HOW to Obtain Service ServiceThis Warranty does not Cover WarrantyLimited Warranty HOW Long does the Limited Warranty LAST?No Other Warranties HOW to GET ServiceCommercial USE Page LA Collection Professionnelle Liberty Veuillez Conserver CE Manuel À Titre DE Référence ’INTENTION DE NOS ClientsUtilisation DE LA Plaque Chauffante Table DES MatièresPage Mesures DE Sécurité ET DE Précaution Hauteur de Emplacement ’APPAREIL D’EXTÉRIEURRemaque Modèles D’APPAREILS D’EXTÉRIEUR BFG-30G Tout gril Avant D’UTILISER L’APPAREILEmplacement Emplacement DE L’APPAREIL D’EXTÉRIEUR ET DES DégagementsEnveloppe Isolée Emplacement DES DégagementsGénéralités Disposition standard pour une enceinte non combustible Détails D’UNE Construction IntégréeInstructions DE Montage DE Chariot Placement DE LA DesserteÉtape Préparation de la tête de l’appareil d’extérieur Points DE Pincement Accrochez Branchement du gaz PropanePour Connecter LES Raccords Fournis Avec LE Gril Branchement DU GAZExigences Concernant LE GAZ Exigences Concernant LA Bouteille DE Propane Branchement DU Propane Régulateur DE Type 1 OU QCC145,7 cm 18 po Max Placez le dispositif de retenue de bouteille dans l’îlot Fig Avant la vérification Efficacité DES Brûleurs ET Caractéristiques DE LA Flamme Test DE Détection DES Fuites Brûleur LatérauxRéglage DES Brûleur Brûleur Latéraux BrûleursRéglages Pour Niveau BAS Hauteur DES Flammes DU Brûleur DU GrilInstallation DE L’ENSEMBLE DU Radiant Installation DE L’ENSEMBLE DU RadiantÉvier Installation DES RobinetsInstallation DE L’ÉVIER Tablette Latérale accessoire en option Veuillez Lais Liste DE Contrôle DE L’INSTALLATEURInstructions D’ALLUMAGE Utilisation DU GrilUtilisation DU Gril Conseils AU Sujet DU Gril Important Utilisation du grilAllumage À L’ALLUMETTE Utilisation DU Drûleur LatéralTableau DE Cuisson DE LA Plaque Chauffante Utilisation DE LA Plaque ChauffanteUtilisation DE LA Plaque Chauffante Utilisation DE LA Plaque Chauffante Utilisation DE L’ÉVIER Nettoyage DES Grilles DU Gril Remplacement DE LA PileRemplacement DU Régulateur ET DU Tuyau Entretien ET NettoyageBrûleur DU Gril Entretien ET MaintenanceTiges EN Céramique Acier InoxydableGrille DU Brûleur Latéral Nettoyage DE L’ORIFICEÉvier Électrodes DE Brûleurs LatérauxPlaque Chauffante Boutons DE RéglageDépannage Appareil D’EXTÉRIEUR Avant D’APPELER LE Service TechniqueProblème Solution Dépannage Brûleur Latéral Pour L’OBTENTION DU Service DE Garantie Quelle EST LA Durée DE LA Garantie LIMITÉE? GarantieGarantie Limitée Fisher & Paykel S’ENGAGE ÀAucune Autre Garantie Pour Obtenir DES RéparationsUtilisation Commerciale Remarque Remarque Remarque Page Litho in USA 09/2001
Top Page Image Contents