Invacare PANTHER LX-4, PANTHER MX-4 REMOVING/INSTALLING the CRUTCH/CANE Holder Figure, Parts

Page 56

PARTS

PROCEDURE 11	OPTIONS/REPLACEMENT PARTS

REMOVING/INSTALLING THE CRUTCH/CANE HOLDER (FIGURE 4)

NOTE: The Crutch/Cane Holder, Safety Flag, and Oxygen Holder all install into the accessory tube; ONLY one (1) of these may be installed at a time. These accessories are NOT available on the ZOOM-3.

OPTIONS/REPLACEMENT

NOTE: To remove, reverse the following procedure.

WARNING

The installation of the crutch/cane holder onto the back of the scooter seat significantly increases the length of the scooter. When turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise, injury and/or damage to the

surrounding property may result.

Seat

Crutch/

Cane

Holder

	Hook			Mounting
		Accessory
				Screw
	Base	Tube

FIGURE 4 - REMOVING/

INSTALLING THE CRUTCH/CANE

HOLDER

INSTALLING

1.Install the crutch/cane holder into the accessory tube located on the back of the seat.

2.. Install mounting screw to secure the crutch/cane holder in place. Securely tighten.

3. Align slot on base with hook on crutch/cane holder and slide base down into position.

REMOVING/INSTALLING THE SAFETY FLAG (FIGURE 5)

NOTE: To remove, reverse the following procedure.

WARNING

The installation of the safety flag onto the back of the scooter seat significantly increases the length of the scooter. When turning the scooter or swiveling the scooter seat, it is important to take note of this increased length - otherwise, injury and/or damage to the surrounding property may result.

Seat

Safety

Flag

Accessory Mounting

BracketTube Screw

FIGURE 5 - REMOVING/

INSTALLING THE SAFETY FLAG

INSTALLING

1.Install the bracket into the accessory tube located on the back of the seat.

2.Install mounting screw to secure the bracket in place. Securely tighten.

3.Install safety flag into bracket.

Invacare Scooters

56

Part No. 1090132 Rev F

Image 56

Contents Invacare Scooters Special Notes Table of Contents Procedure 10 Transport Specifications SpecificationsSpecifications General Guidelines Procedure General WarningsOperating Information General GuidelinesElectrical Procedure General GuidelinesRamps Weight Limitation General Warnings Grounding InstructionsBatteries Rain TestGeneral Guidelines Important Information SAFETY/HANDLING Percentage of Weight DistributionStability and Balance Always wear your seat positioning strapStairways ESCALATORS? SorryDelta Tiller Standard TillerSafety INSPECTION/MAINTENANCE Safety INSPECTION/ MaintenanceSafety INSPECTION/MAINTENANCE Procedure MaintenanceSuggested Maintenance Procedures Lubrication Points Figure Detail aTroubleshooting Guide Procedure Safety INSPECTION/MAINTENANCEControl Panel Features Operation ProcedureALL Scooter Models With Delta or Standard Tillers FigureProcedure Operation Detail a ZOOM-3Delta Tiller Panther MX-4 WDetail F Panther MX-4 Scooters onlyWith Delta Tillers Figure Procedure Operation Operation of the Scooter FiguresUsing the Hand Brake LEVER/BRAKE ARM Figure Hand Brake LeverBrake ARM Delta TillersPanther MX-4 only Figure Brake Release LeverALL Models Except Panther MX-4 Figure Circuit Breaker Reset Circuit BREAKER/FUSE Replacement FigureFuse Replacement REMOVING/INSTALLING the Batteries with Cables Figure Procedure BATTERIES/CHARGINGRemoving BATTERIES/CHARGINGReplacing the Batteries Figure Recommended Battery TypesBATTERIES/CHARGING Procedure BATTERIES/CHARGING Cleaning Battery Terminals DiatelyModel Battery Charger Power Cord Charging the BatteriesRemote Battery Charger Figure ON-BOARD Battery Charger FigureBattery Charger Operation Figure Battery Charger Operation Remote and ON-BOARDREMOVING/INSTALLING the Seat Seat ProcedureDetermining Seat Post Type Figure SeatRemoving Figure Installing FigureProcedure Seat Adjusting the Seat Height Solid Seat Post FigureAdjustable Height Seat Post Figure Detail aALL Models Except ZOOM-3 Figure Adjusting the Seat DepthAdjustment Using the Adjustable Seat Slide Figure Adjusting the Seat DepthREMOVING/INSTALLING the Seat UPHOLSTERY/ Cushion Figure InstallingREMOVING/INSTALLING FOLDING/UNFOLDINGBack Figure Back CUSHION/UPHOLSTERY FigureAdjusting the Back Recline Adjusting the HeadrestBack Procedure ALL Models Except ZOOM-3, SX-3 and LX-3 FigureArmrest Width Armrest Angle AdjustmentAdjustment Height Figure Armrest DEPTH/HEIGHT AdjustmentALL Models Except ZOOM-3 Figure Depth Tiller Angle Adjustment Tiller AdjustmentProcedure Tiller Adjustment Fold Down Tiller ZOOM-3 FigureALL Other Models Figure FivePosition Models Built AfterALL Models REMOVING/INSTALLING the Rear Shroud FigureProcedure SHROUD/WHEELS Turn Power OFF and remove key from ignition REMOVING/INSTALLING the Rear Wheels FigureSHROUD/WHEELS Procedure REMOVING/INSTALLING the Front Wheels Figure SHROUD/WHEELSModels ZOOM-3 and Lynx SX-3 Models Lynx LX-3 and LX-3 PlusDo not USE TOP Mounting HoleProcedure Transport Transporting the Scooter Figures 1Disassembling the Scooter TransportDetail B Models Built with Delta Tillers Transporting the Scooter for ALL Models Except ZOOM-3Transport Procedure Cable Side ViewALL Models Except ZOOM-3 Steps 8 and 9 for ALL Models Except ZOOM-3Disassembled View Procedure OPTIONS/REPLACEMENT Parts REMOVING/INSTALLING the Front Basket FigureOPTIONS/REPLACEMENT Parts OPTIONS/REPLACEMENT Parts Procedure REMOVING/INSTALLING the Floor Basket FigureREMOVING/INSTALLING the Seat Positioning Strap Figure REMOVING/INSTALLING the CRUTCH/CANE Holder Figure REMOVING/INSTALLING the Safety Flag FigureOPTIONS/REPLACEMENT PartsANTI-TIPPER Wheel Assembly ANTI-TIPPER WheelsReplacing Seat Lever Figure Replacing Seat LeverReplacing Tiller Angle Adjustment Lever Figure Replacing Headlight LightbulbsModels Lynx LX-3 and Panther LX-4 Figure Lynx LX-3 and Panther LX-4Detail a Back View of Headlight Assembly Model Panther MX-4 FigureReplacing ON-BOARD Battery Charger Figure Replacing ON-BOARD Battery ChargerInvacare Scooters Part No Rev F Limited Warranty Limited W ArrantyOne InvacareWay