Cortelco 2750 Timer Reset, Elapsed Call Time Previous Calls, Headset, Directory Card, Pre-dialing

Page 44

6.15.2.Timer Reset

Press the up arrow (^)button, which is found directly below the display.

6.15.3.Elapsed Call Time (Previous Calls)

While the phone is on-hook and idle, press REDIAL. The display will show the elapsed time of the previous call, along with its time and date. Use the right arrow button under the display to view the lengths of the previous five calls, along with their times and dates.

6.16.Headset

Your 2750 is headset-ready. It comes equipped with a 2.5mm headset jack, and a built-in headset amplifier, along with a dedicated HEADSET button. To use this feature, plug a telephone headset with a 2.5 millimeter plug into the headset jack. There is no need to buy a headset with a separate amplifier. You can use your headset to make or answer an outside call, an intercom call or a page. Simply press HEADSET instead of lifting the handset. During a call, you may switch back and forth between handset, headset and/or speakerphone as much as you like.

If you wish to override automatic line selection, press the desired LINE button instead of pressing HEADSET, and you will be connected to that line on the speakerphone. Then press HEADSET to toggle to the headset. Press HEADSET again to hang up.

6.17.Directory Card

Remove the directory card and write down the names or telephone numbers associated with line numbers.

6.18.Personal Directory

a.While the phone is on-hook and idle, press the “#” button. The display will read “Directory.”

b.Use the up and down arrow buttons below the display to view the personal directory entries.

c.When the desired entry is displayed, you may dial it simply by lifting your handset, by pressing SPEAKER or HEADSET, or by pressing a desired LINE button.

Note: The directory is organized alphabetically. You may jump to your desired entry by pressing the corresponding dial pad number. For example, press the “5” dial pad button three times to jump to the first entry starting with “L”. You can then use the up and down arrow buttons to view the entries starting at that point.

6.19.Pre-dialing

Pre-dialing allows you to enter a telephone number and check it in the display before it is dialed out. To make a pre-dialed call, enter the number using the dial pad while the telephone is on-hook, then lift the handset or press SPEAKER or HEADSET or press the desired LINE button. If you make a mistake while dialing the number, you can use DELETE to erase digits one at a time.

6.20.Intercom Calls

You may place an intercom call by dialing the two-digit station number of the desired station. When you place an intercom call, your speakerphone turns on automatically. If the called station is set to INTERCOM RING, you may speak to the station as soon as they answer.

If the called station is set to INTERCOM VOICE or INTERCOM HANDSFREE, you may speak to the station after you hear the confirming tone.

38

2750 User Guide Version 1.3

Page 43 Page 45
Image 44
Page 43 Page 45
Contents OWNER’S Instruction Manual Table of Contents Memory Settings Iii User Guide Version Using Your Telephones Answering System Using Stanard Telephones Thank YOU For Purchasing Feature List User Guide Version Important Safety Instructions Unpacking and Installation Box ContentsTelephone Part Identification Identify Your Existing Wiring System Plan Your InstallationStandard Installation Installations with Private Lines and Unconnected LinesConnect Cords to Telephone Install Batteries OptionalAssign a Station Number Verify Proper Installation System ProgrammingStation Number Assignment Station Name AssignmentLine Configuration/Type To Set Loop Voltage Detector To Set Connections/ConfigurationLoop Voltage Detector To choose how each line will ring Ringer ConfigurationSetting Distinctive Ringing To choose how your phone will respond to intercom calls Setting Off-Hook RingingIntercom Call Response To set the system’s toll restriction access code Automatic Line SelectionTo Set Automatic Line Selection Toll RestrictionTo completely restrict specific lines at a telephone RestrictedTo set the allowed numbers at a particular telephone System PrivacyArea Codes To Change the Privacy SettingDialing Mode Memory Settings Storing a Caller ID number into memory To store a personal directory dial numberTo Store Caller ID Records To Store the Centrex PrefixErase All Feature Settings Reset Default SettingsErase Numbers Stored in Memory Erase Toll RestrictionsMiscellaneous Settings Adjusting Auto Hold Drop Time Adjusting Flash TimerCaller ID on Call Waiting Cidcw Sensitivity Hold Call ReminderAnswering System Setting Your Telephones Pickup Delay Setting Toll SaverChanging your OGM New Message BeepAuto-Attendant Setting Message LengthRemote Code Record your Auto Attendant Night OGM Set up the Auto AttendantRecord your Auto Attendant Day OGM Record your Auto Attendant Zero-Out OGM Setting Auto Attendant Pickup DelayNight Timer Set Setting More Than One Phone as an Auto Attendant Using Additional Auto Attendant OGMsSetting Separate Auto Attendant OGMs for Different Lines To record additional Auto Attendant OGMAll Transfer Feature Turn Off the Auto Attendant on One or More LinesChoosing the Zero-Out Action Leave a Message at the Auto AttendantTransfer Direct to Voice Mail Summary of Auto Attendant ActionsTelephone Operation Answering a call on another line ConferenceOutside Calls Outside Call with Intercom StationBlind Transfer Transfer RingPersonal Ring Caller IDVolume Levels Dialing CallsDeleting Numbers RingerAccessing Messages Resetting MSG LampSpeakerphone Intercom SpeakerFlash MuteDo Not Disturb DND Line ReserveTimer Elapsed Call Time Call PrivacyToll Restriction Removal Single Call Toll Restriction Removal Single StationTimer Reset Elapsed Call Time Previous CallsHeadset Directory CardIntercom while Idle Intercom while on an Outside CallAnswering Intercom Calls Intercom Ring Intercom VoiceAll Answering Pages SingleBlocking Pages Room MonitoringUsing Your Telephones Answering System Listening to your Messages Play MessagesStop Message Playback Pause Message PlaybackUsing Dial Pad Repeat a MessageSkip to the next Message Jump backErasing Messages To Erase a Message To Erase All MessagesRecording a Memo or Conversation Recording a Telephone ConversationUsing Stanard Telephones To Repeat an Auto Attendant OGMLine Status and Calls on Hold IntercomBatteries Battery ReplacementPower Failure Operation Menu Tree Phone SettingsAppendix a ON/OFF Answer Settings Menu Options SUB Menu DefaultAdvanced Settings Memory SettingsTime and Date Settings Installation Worksheet Appendix BAppendix C Toll Restriction WorksheetTrouble Shooting Guide Appendix DFCC Information Telephone Repair Limited Warranty Repair Center Sawyer Road Corinth, Mississippi
Top Page Image Contents