Emerson 400501-08 manual Mechanical Installation, DeviceNet Hardware Components, Cables

Page 17

Installation

Mechanical Installation

Follow the instructions for mechanical installation of an Epsilon Ei Drive as outlined in the Epsilon Ei Installation Manual (P/N 400501-06).

DeviceNet Hardware Components

The following components are necessary to design a DeviceNet cable system:

•Cables

•Nodes/Devices

•Connectors

•Power Supply

•Terminating Resistors

Cables

These cables can be obtained from the supplier of the DeviceNet Network Master. (For more details see the ODVA Specification Volumes I and II, Release 2.0.)

Thick Cable

The thick cable consists of two shielded pairs twisted on a common axis with a drain line in the center covered with an overall braid. The shield is commonly used as a trunk line when length is important.

Thin Cable

The thin cable is smaller and more flexible than the thick cable. It is commonly used for drop lines but can be used for shorter distances as a trunk line.

Nodes/Devices

A DeviceNet slave is any device that is addressable through DeviceNet and contains DeviceNet communications circuitry. DeviceNet Slaves must comply with the following:

A slave must be connected to the network by a tap and drop-line. Slaves must be DeviceNet-compatible devices.

63 Slaves can be supported on one network.

Each Slave must be assigned a media access control identification number (MacID). MacID’s on a single network must be unique.

5

Image 17

Contents Reference Manual Page Epsilon Ei DeviceNet Drive Reference Manual Page 952 Customer SupportWebsite and Email Technical Support 952 995-8033 or 800Customer Service Sales 952 995-8000 or 800 Training Services 952 995-8000 or 800Document Conventions Application Engineering 952 995-8000 or 800This Represents Reference Materials Safety InstructionsGeneral Warning Qualified PersonSafety Precautions Safety ConsiderationsSetup, Commissioning and Maintenance EnclosureGeneral warning Safety of MachineryTable of Contents Explicit Messaging Quick Start Network Configuration Quick StartDrive Parameters Appendix Glossary IndexPurpose IntroductionDeviceNet Communications Link DeviceNet OverviewMaster/Slave Relationship DeviceNet Messaging and CommunicationsMaster/Slave Relationship Mechanical Installation InstallationDeviceNet Hardware Components CablesConnectors Electrical InstallationPower Supply Requirements Physical Connections to the DeviceNet NetworkInstallation Epsilon Ei DeviceNet Drive Reference Manual Software Interface Connection TypesDeviceNet Tab Polled I/O Connections Implicit MessagingMacID Master Receive and Master Send Assembly Block SelectionsBaud Rate Index Select Predefined Index Sel PredefIndex Select User Defined Index Sel UserDef Configuring the DeviceNet NetworkPosition Control Index TypeCCW No OperationCode Description Input Word Select Data PointerOutput Word Select Data Pointer Response Assembly Codes Command Assembly CodeConfiguring the DeviceNet Network Ei-DN Input Processing Logic Host Mode EnableCounters DeviceNet Online TabInformation Established Connections StatusNetwork Status LED Module Status LEDDeviceNet Bits Input and Output TabFaults and Diagnostic Display Ei-DN Modbus Address DN Allocation Choice Connections EstablishedDN Allocation Master MacID DN Baud Rate DN Bus Off Fault CountDN Bus Off Counter DN Bus Off InterruptDN Duplicate MacID Fault Count DN Comm Time-out Fault CountDN Device Type DN FAB Master Receive BlockDN MacID DN Host ModeDN FAB Master Send Block DN Master Send Bitmap DN Master Receive BitmapDN Master Receive FAB Type DN Module Status DN Master Send FAB TypeDN Status Major Unrecoverable Fault DN Status Major Recoverable FaultDN Network Status DN Receive CounterDN Status Minor Unrecoverable Fault DN Status Minor Recoverable FaultDN Transmit Counter DN Vendor IDModule Status LED Accessing the EDS FileHardware Interface Viewing and Changing the Baud Rate and MacID Setting the Baud Rate and MacID Externally One TouchNetwork Status LED Display Value Baud Epsilon Ei DeviceNet Drive Reference Manual Equipment Network Configuration Quick StartExample #1 Index SelPredef Polled I/O SetupNetwork Configuration Quick Start Example #2 Index Sel Userdef DN Setup / Index Sel Userdef Inputs Tab Outputs Tab Example #3 Index Type DN Setup / Index Type Output Word Select Input Word Select Example #4 Position Control Dn Setup / Position Control Network Configuration Quick Start RS Networx Configuration Master ConfigurationScanlist Tab Input Tab Output Tab Epsilon Ei DeviceNet Drive Reference Manual Explicit Messaging Quick Start How to Send Explicit MessagesExecute Description of N10 Integer File Explicit Messaging ExamplesExample 1 Read Index 0 Velocity Explanation of PLC ProgramExamples Integer File N11 High Byte Low Byte Example 2 Write Index 1 VelocityInterger File N10 High Byte Low Byte Explicit Messaging Quick Start Epsilon Ei DeviceNet Drive Reference Manual By Name Drive ParametersName DeviceNet Data TypeUdint Drive Parameters ProductID.Option1IDFunctionModule By DeviceNet Class 0x01 DeviceNet.DeviceNetIdentityObject.DeviceType 104 0x68 See Note 0x09 Index.Instance#.RegistrationOffset 109 0x6D 0x01 0x04 Position.FollowingError 0x01 0x0D Status.TorqueFeedback Epsilon Ei DeviceNet Drive Reference Manual Index Select Predefined AppendixIndex Select User Defined Master Receive Assembly Block Index Sel User DefIndex Type CCW Position ControlGlossary Epsilon Drive Drop LineExplicit Message Explicit Messaging ConnectionsConnections One touch ConfigurationLink Consumer Object Link Producer ObjectUcmm Index Epsilon Ei DeviceNet Drive Reference Manual Index Epsilon Ei DeviceNet Drive Reference Manual