Xantrex Technology 809-0912 manual Typical RV Wiring Diagram With Freedom Sequence

Page 16

FSequence IPM Owners Guide.book Page 6 Thursday, October 6, 2011 3:33 PM

Typical RV Wiring

IMPORTANT: This illustration is not a detailed technical wiring schematic.

NOTE: The Freedom Sequence power manager must be permanently installed by a qualified installer in a controlled environment.

Figure 3 shows a simple configuration where the power manager is installed with a power supply line (either shore or generator), one Freedom SW inverter/ charger, a Xanbus SCP, a Xanbus AGS, and various electrical appliances in a typical RV. Means of over- current protection and disconnection must be incor- porated into the fixed wiring, in accordance with the electrical code that governs each installation.

300A

Inverter/Charger

INVERTER

SUBPANEL

SCP

MAIN AC

PANEL

AGS

A

BATT

DC AUX

HARNESS

B+ SIGNAL

GENERATOR

ALTERNATOR

12V FUSE

PANEL

ISOLATOR

A

START

HOUSE

DC RELAY 1

50A

AC 6

AC 5

AC 4

AC 3

AC 2

AC 1

30A

DC RELAYS

	BATTERY	AC LINE	50A	AC DISCONNECT
	DC LINE	XANBUS	300A	DC DISCONNECT	TO SHORE
	DC LINE	XANBUS	300A	DC DISCONNECT	CONNECTION
					CONNECTION

Figure 3 Typical RV Wiring Diagram With Freedom Sequence

		6			Freedom Sequence Intelligent Power Manager Owner’s Guide

Image 16

Contents Freedom Sequence Page Contact Information About This Guide Purpose Conventions UsedRelated Information Important Safety Instructions ReferencePrecautions When Placing the Power Manager Explosion HazardRisk of Damage to the Power Manager FCC Information to the UserContents Page Standard Features IntroductionMaterial List Compatible Products and Accessories1 Product/Accessory Product NumberTypical Xanbus System Diagram Xanbus SystemMechanical Features Ports and TerminalsTypical RV Wiring Typical RV Wiring Diagram With Freedom SequencePower Manager Configuration EnterFuncPower Manager Configuration Circuit Status Circuit StatusCont Circuit Status List of configurable settings includes Basic Configuration SettingsConfig Circuit Config List of circuit configurable settings includesPriority To change the Mode from the Device Status screen ModeMode OperatingShore Breaker Mode SHR BKR ModeAuto ManualBreaker Ratings Shore Breaker Rating30.0A 25.0ATo Restore Defaults from the Device Status screen Restore DefaultsRestore Defaults Config Circuit Circuit ConfigurationCircuit Priority To change the priority setting from the Device Status screen Config Circuit ConfigEnabled Load ShedTo change the Load Shed from the Device Status screen Load ShedAdvanced Settings Improper Configuration DUE to Lack of ExperienceAdvanced Settings List of advanced settings includeBKR Derating Config Advanced Settings Breaker DeratingGenerator Warmup Delay GEN Warmup DelayGenerator Breaker Rating ScreenConnect Seq Delay Connect Sequence Delay10sec AC Disqualification Priority AC Disc PriorityNom DC Voltage DC Voltage Setting12.0V Circuit2 Circuit Level Advanced SettingsCircuit Name AC Relay Settings DC Relay SettingsCircuit Name Circuit3Circuit Type AC LinePriority Generator Soft StartBattery Voltage Triggers Reconnect MarginFreedom Sequence Operational Concepts Auto-Detection of AC Input Source Shore/GenAuto-Detection of AC Input Source Type 1-Ph/2-Ph Loading of Shore/Generator Breaker RatingsAC Load Shedding LINE1 L1 LINE2 L2 Using DC Relay to control AC load circuits DC Load SheddingPriority Swapping Between Circuits Override the AC Circuit Load Shedding Battery Voltage Measurement Generator Run Detection B+ SignalFreedom Sequence Interaction with Other Xanbus Devices Freedom SW Interactive Charger De-rating ICDFreedom Sequence SCP Menu Map Specifications Warranty and Return Information WarrantyWarranty and Return Information Disclaimer ProductOut of Warranty Service Return Material Authorization PolicyReturn Procedure Information About Your System Page Xantrex Technology USA Inc