Xantrex Technology 809-0912 manual Freedom Sequence SCP Menu Map

Freedom Sequence SCP Menu Map

40
Device Status Screen
FSPM 00: Status
AC Src Type	1-Ph
AC Source	Shore1
L1 Amps	0.0A
L2 Amps	0.0A
Batt Voltage	12.0V
Circuit Status
Config
Advanced Settings

NOTE: The Screens as shown in this Menu Map are typical of the six-circuit Freedom Sequence model.

For example, in the Circuit Status screen, a four-circuit Freedom Sequence model will show only eight circuits – four AC circuits and four DC circuits.

Freedom Sequence

SettingsIntelligentPower

FSPM 00: Circuit Status
1	ACLoad1		On 3.0A
1	Last Shed Current			6.0A
2	ACLoad2		On 4.5A
2	Last Shed Current			4.0A
3	ACLoad3		On 2.5A
3	Last Shed Current			2.5A
4	ACLoad4		On 2.3A
4	Last She Current			2.0A
5	ACLoad5		On 3.7A
5	Last Shed Current			1.0A
6	ACLoad6		On 3.0A
6	Last Shed Current			4.0A
7	DCLoad1			On N/A
7	Last Shed Current			N/A
8	DCLoad2			On N/A
8	Last Shed Current			N/A
9	DCLoad3			On N/A
9	Last She Current			N/A
10 DCLoad4				On N/A
10 Last Shed Current				N/A
FSPM 00: Config
					1
Mode		[Operating]
SHR BKR Mode				[Auto]	2
SHR BKR Rating			[30.0A]		3
Circuit Config
Restore Defaults
FSPM 00: Advanced Settings
					4
BKR Rating		[Enabled]
GEN BKR Rating			[30.0A]		5
GEN Warmup Delay				[0sec]	6
Connect Seq Delay			[10sec]		7
AC Disq Priority				[2]	8
Nom DC Voltage			[12.0V]		9
Circuit1
Circuit2
Circuit3
Circuit4
Circuit5
Circuit6
Circuit7
Circuit8
Circuit9
Circuit10

					Freedom
2	Load Shed	[Enabled]Freedom
FSPM 00: Circuit Config
1	ACLoad1				10
1	Priority			[1]
1	Load Shed	[Enabled]			11
2	ACLoad2			SequenceSCP	SequenceSCPMenuMap
2	Priority			[2]
3	ACLoad3
3	Priority			[3]
3	Load Shed	[Enabled]
4	ACLoad4
4	Priority			[4]
4	Load Shed	[Enabled]
5	ACLoad5
5	Priority			[5]
5	Load Shed	[Enabled]
Cont
FSPM 00: Circuit Config
6	ACLoad6
6	Priority			[6]
6	Load Shed			Menu
		[Enabled]
7	DCLoad1
7	Priority			[7]
7	Load Shed	[Enabled]
8	DCLoad2
8	Priority			[8]
8	Load Shed			Map
		[Enabled]
9	DCLoad3
9	Priority			[9]
9	Load Shed	[Enabled]
10 DCLoad4
10 Priority				[10]
10 Load Shed		[Enabled]
FSPM 00: Circuit 1
					A
Circuit Name		[ACLoad1]
Load Shed		[Enabled]			B
Circuit Type [ACInputOut]					C
AC Line			[Line1]		D
Priority				[2]	E
Reconnect MRGN			[10%]		F
GEN Soft Start		[Disable]			G
Batt Low Trig Set			[10.5V]		H
Batt Low Trig Clr			[11.0V]		I
Batt High Trig Clr			[14.0V]		J
Batt High Trig Set			[14.5V]		K

Owners Guide.book Page 40 Thursday, October 6, 2011 3:33 PM

1

3

2 Manager

4

5

6	Owner’s
7
8
9
10
	Guide

11

[*Operating] or [Standby] [*Auto] or [Manual]

[*30.0] [5.0] to [50.0] [*Enabled] or [Disabled] [*30.0] [5.0] to [50.0] [*0] [1] to [120] [*10] [4] to [60] [*1] [1] to [10] [*12.0V] or [24.0V] [*1] [1] to [10] [*Enabled] or [Disabled]

A	[*ACLoad1] see NOTE below
B	[*Enabled] or		[Disabled]
C	[*ACInputOut] or				[DCInputOut]
D	[*Line1] or [Line2] or [Batt1]
E	[*1] [1] to		[10]
F	[*10]	[1] to	[100]
G	[*Disable] or		[Enable]
H	[*10.5]	[4.0]		to	[40.0]
I	[*11.0]	[4.0]		to	[40.0]
J	[*14.0]	[4.0]		to	[40.0]
K	[*14.5]	[4.0]		to	[40.0]

NOTE: Circuit names can be up to ten characters long. Valid characters are from a to z, A to Z, 0 to 9, symbols '/' (forward slash) and '–'(hyphen). Spaces, an underscore, and a period are not accepted symbols. Examples are “Main-A/C” and “Refrigerat”.