Fortinet 4.0 MR1 manual Go to System Network Options, Go to Router Static Static Route

Page 20

Configuring basic FortiGate Voice network and UTM settings

Example FortiGate Voice branch office configuration

Addressing Mode

Manual

IP/Netmask

192.168.10.10/255.255.255.0

SIP Traffic

Select Enable

Configure other network interface settings as required and select OK.

Note: You can also set the Addressing mode to DHCP or PPPoE for the wan1 interface depending on the requirements of your ISP. In the example the wan1 interface has a static IP address.

5Go to System > Network > Options.

6Add the IP addresses of the primary and secondary DNS servers used by the branch office provided by your ISP.

7Selected internal for Enable DNS forwarding from so that users on the internal network can use the FortiGate Voice internal interface as their DNS server IP address.

The procedure “To configure the FortiGate Voice to be a DHCP server for the internal network” on page 20 describes how to configure the FortiGate DHCP server to configure PCs on the internal network to use the FortiGate Voice internal interface as a DNS server.

8Select Apply.

9Go to Router > Static > Static Route.

10Edit the default static route and configure the following settings:

Destination IP/Mask

0.0.0.0/0.0.0.0

Device

wan1

Gateway

Enter the IP address of the default gateway provided by your ISP.

Distance

10

11Select OK.

To configure the FortiGate Voice to be a DHCP server for the internal network

Use this procedure to add a new DHCP server for the internal network or to change the configuration of the default FortiGateVoice DHCP server. The DHCP server will give PCs on the Internal network IP addresses in the range 172.20.120.110 to 172.20.120.210 and set their default gateway and DNS server to the IP address of the FortiGate Voice internal interface.

1Go to System > DHCP > Service and select the expand arrow for the internal interface.

2Select the Add DHCP Server icon for the internal interface.

If a DHCP server has already been added for the internal interface, select the Edit icon to change its configuration.

3Configure the following settings.

Name

Add a name for the DHCP server if you are adding a new one.

Enable

Select

Type

Regular

IP Range

172.20.120.110 - 172.20.120.210

Network Mask

255.255.255.0

Default Gateway

172.20.120.10

 

 

 

FortiGate Voice Version 4.0 MR1 Administration Guide

20

01-410-112851-20100601

 

http://docs.fortinet.com/ • Feedback

Page 19 Page 21
Image 20
Page 19 Page 21
Contents FortiGate Voice FortiGate Voice Administration Guide TrademarksContents Configuring extension groups ring groups FortiGate Voice VoIP, PBX, and Pstn CLI ReferenceIntroduction Fortinet products Before you begin How this guide is organizedHow this guide is organized How this guide is organized Document conventions IP addressesHead Office, second FortiGate Branch Office, one FortiGateOffice 7, one FortiGate with VDOMs Office 3, one FortiGate, webExample Network configuration Example network configurationDocument conventions CLI command syntax conventions Typographical conventionsAngle brackets Curly bracesRegistering your Fortinet product Fortinet products End User License AgreementTraining DocumentationCustomer service and technical support Fortinet Tools and Documentation CDFortinet Knowledge Base Comments on Fortinet technical documentationExample FortiGate Voice branch office configuration General configuration steps Example Branch Office network configurationConnecting the FortiGate Voice unit Configuring basic FortiGate Voice network and UTM settingsTo configure basic network settings To connect the FortiGate Voice unitGo to System Network Options Go to Router Static Static RouteGo to System Maintenance FortiGuard To configure basic Internet access and UTM featuresAdvanced DNS ServerConfiguring the FortiGate Voice Pstn and PBX settings To configure the fxo1 Pstn interfaceGo to PBX Calling Rules Setting Caller ID IndicatorCaller ID Protocol Ring #To add a dial plan for dialing the Pstn and the main office Go to PBX Service Providers SIP TrunkTo add a VoIP provider Phone number Begin with O11 Action Block Use Default Outgoing Prefix SelectedGo to PBX Calling Rules Dial Plan and select Create New Go to PBX Extension Extension and select Create New Configuring the FortiFones on the internal network To configure FortiFones on the internal networkTo add an extension for a SIP phone behind a NAT device 6010 FortiGate Voice IVR configuration Providing access to the company directoryTo configure the remote FortiGate unit in NAT mode To add a custom welcome messageAdding a shortcut for checking voicemail Checking voicemailGo to PBX Calling Rules Voice Menu Go to PBX Call Voice MenuAdding a shortcut for checking voicemail System resources dashboard widget Dashboard widgetsUnit operation dashboard widget To configure VoIP interface settings Configuring VoIP interface settingsConfiguring Pstn interfaces Basic Options General Pstn interface settingsPstn interface configuration settings PBX configuration Configuring service providersConfiguring extensions VoIP ProviderGeneral extension settings Extension configuration settingsCreate New Dial PlanConfiguring extension groups ring groups Configuring extension groupsConfiguring dial plans Voicemail Extension MemberGeneral dial plan list settings Dial plan rule configuration settingsName Use Default Outgoing Prefix9 Go to PBX Calling Rules Dial Plan to add a dial planExample dial plan PrependConfiguring voice menu options To configure voice menu optionsConfiguring direct inward dialing General direct inward dialing settingsDirect inward dialing configuration settings Name Incoming Extension CommentsConfiguring PBX settings PBX Global SettingsVoicemail Notification Email Settings You must also add a username and passwordMonitoring calls Monitoring SIP Trunk statusTo configure logging of PBX settings Go to Log&Report Log Config Event LogLogging of PBX activities Viewing log messagesLogging of PBX activities Config pbx dialplan SyntaxConfig pbx did Variables Description DefaultConfig pbx extension Config pbx global Variables Description DefaultConfig pbx ringgrp Config pbx smtp Config pbx voice-menu Config pbx voip-providerSecret password Edit providernameUser username DomainConfig system pstn Variables Description Config system interfaceExecute pbx Example command output Diagnose pbx restart
Top Page Image Contents