AT&T 7720 user manual Speakerphone Volume Control, Mute, Handset Locator

Page 26

TELEPHONE OPERATION

AT THE BASE

Answering a Call

To answer using the speakerphone, press Kon the base. The speaker light goes on and the call is connected. To end the call, press Kagain.

Speakerphone Volume Control

Press +to increase speakerphone volume. Press -to decrease volume.

Mute

Mute allows you to hear your caller, but prevents the caller from hearing you. To activate the Mute feature, press m, then select MUTE while on a call. The MUTE light on the base goes on and the screen displays MUTE. To deactivate the Mute feature, select UNMUTE.

Hold

Press H. The SPEAKER light flashes. To return to the call, press Hagain

— OR —

Press Pon the handset

— OR —

Press Kon the base

— OR —

Lift the handset of an extension phone on the same line.

Page/Intercom

The Page feature allows you to signal someone at the handset from the base.

1Make sure the HANDSET IN USE light on the base is off.

2Press ion the base. This sends a three-part paging tone to the handset.

3The display will show PAGING FROM BASE. Select INTERCOM. The INTERCOM/HANDSET LOCATOR light on the base goes on and the handset and base can communicate with each other without tying up the telephone line.

4Select OFF on the handset to close the intercom connection.

Handset Locator

This feature is useful if you misplace the handset.

To locate the handset using this feature, press and hold

ion the base for approximately four seconds. A repeating

paging tone is sounded at the handset.

To cancel the Handset Locator feature, press hon the handset or

ion the base.

This feature will automatically turn itself off in approximately three minutes if you haven’t turned it off before then.

24

Image 26

Contents User’s Manual for Digital Answering System Philips Consumer Communications L.P. All rights reserved Table of Contents Table of Contents Handset Batteries Installation Installation Set the handset Ringer switch Table/Desk InstallationInstall the handset battery Install the power reserve batteries Connect the telephone line cordCheck for a dial tone Connect the power cordSet the dial mode Wall Installation Follow Steps 7 to 12 in Table/Desk Installation Telephone Operation Voice Security FlashRedial Temporary TonePage/Intercom Answering a call while using the intercomHold Paging someone at the base from the handsetPower Reserve Feature Recording a Phone ConversationCall Waiting Caller IDAbout Caller Identification To program your local area codes Caller ID SET UPProgramming Local Area Codes Turn Off Caller ID with Call Waiting Call List OptionsCall Announce Caller ID FeaturesNew Call Indicator Recording Call AnnouncementsReviewing Call History Reviewing and Deleting Call AnnouncementsIncoming Call History Removing All Call Records Display DialRemoving Call Records from History Caller ID Display MessagesStoring Numbers in Memory Memory Guard FeatureTelephone Memory Storing a Pause in a Memory NumberViewing Numbers in Memory Storing a Name with a NumberMemory Match Dialing Memory NumbersPriority Ring Numbers Storing a Number Just Dialed in Telephone MemoryReplacing a Stored Number Storing a Number from Call History in Telephone MemoryMute Speakerphone Volume ControlTo locate the handset using this feature, press and hold Handset LocatorOperating Range Changing ChannelsAnswering System SET-UP Speaker Volume ControlSetting the Clock Turning the System On/OffSelecting Your General Announcement Announcement OptionsGeneral Announcements For exampleCaller Specific Announcements Recording Your General AnnouncementDeleting Your General Announcement Setting Up Caller Specific Outgoing Announcements OutgoingFeature Set-Up Announcement Play/SilentAudible Message Alert Remote Access CodeRing Select and Toll Saver Reviewing Feature Settings Priority Call SignalBase Ringer Setting Changing the Priority Calling CodeCall Screening/Intercept Answering System OperationAnswering Calls Announcement BypassListening to Your Messages Delete all messages in a mailbox Saving MessagesDeleting Messages Delete selected messagesMessage Guard Power Fail Protection System Recording a MemoFrom the Cordless Handset Connecting with the Answering SystemVoice Help Menu From a Touch Tone PhoneConnect with the answering system Remote Access CommandsPlaying messages Reviewing Your Announcement Call ScreeningChanging Outgoing Announcement To monitor a callReview ON/OFF Status Recording a Message When System is OffRemote On/Off Turning System OffExit Remote Access Changing SettingsReviewing Settings Handset Batteries Charging the Handset Battery PackReplacing the Handset Battery Pack Replacing the Base Power Reserve Batteries Base Unit BACK-UP BatteriesSignals and Displays Audible SignalsCase of Difficulty If the phone does not work at all, check these items firstIf you hear other calls while using the phone If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you have no dial toneIf messages are incomplete If you hear noise in the handset and the buttons don’t workIf speakerphone conversation sounds distorted If you have difficulty hearing messagesCaller’s name or phone number is not displayed Display Dial feature does not workIf your outgoing announcement isn’t clear Memory Match feature does not work Cordless Digital Answering System Speakerphone End of messages