AT&T 7720 Table/Desk Installation, Install the handset battery, Set the handset Ringer switch

Page 8

INSTALLATION

Table/Desk Installation

1Choose a spot near an electrical outlet and a telephone jack.

•This phone requires a modular telephone jack and a standard electrical outlet not controlled by a wall switch.

2Install the handset battery.

•Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward.

•Plug the battery pack connector into the handset and place the battery pack in the case, so the wires rest between the battery pack and the case.

•Place the battery case compartment on the handset by sliding it on its track up over the battery compartment until it snaps firmly in place.

NOTE: The new batteries must be charged before using this telephone. Place the handset in the base unit and allow it to charge for four hours. The telephone may operate before that, but, for best performance, let the batteries charge fully.

Handset Battery

compartment cover

Battery pack

3Set the handset RINGER switch.

Set the switch on the side of the handset to ON so the handset will ring. When this switch is set to OFF, the handset will not ring.

NOTE: If you set the handset RINGER switch to OFF, the handset battery will last longer. However, when the handset RINGER switch is set to OFF, no incoming call information will appear in the display, the handset will not ring, and the Page/Intercom and Handset Locator features are inactive.

6

Image 8

Contents User’s Manual for Digital Answering System Philips Consumer Communications L.P. All rights reserved Table of Contents Table of Contents Handset Batteries Installation Installation Set the handset Ringer switch Table/Desk InstallationInstall the handset battery Install the power reserve batteries Connect the telephone line cordCheck for a dial tone Connect the power cordSet the dial mode Wall Installation Follow Steps 7 to 12 in Table/Desk Installation Telephone Operation Flash RedialVoice Security Temporary ToneAnswering a call while using the intercom HoldPage/Intercom Paging someone at the base from the handsetPower Reserve Feature Recording a Phone ConversationCall Waiting Caller IDAbout Caller Identification To program your local area codes Caller ID SET UPProgramming Local Area Codes Turn Off Caller ID with Call Waiting Call List OptionsCaller ID Features New Call IndicatorCall Announce Recording Call AnnouncementsReviewing Call History Reviewing and Deleting Call AnnouncementsIncoming Call History Display Dial Removing Call Records from HistoryRemoving All Call Records Caller ID Display MessagesMemory Guard Feature Telephone MemoryStoring Numbers in Memory Storing a Pause in a Memory NumberStoring a Name with a Number Memory MatchViewing Numbers in Memory Dialing Memory NumbersStoring a Number Just Dialed in Telephone Memory Replacing a Stored NumberPriority Ring Numbers Storing a Number from Call History in Telephone MemorySpeakerphone Volume Control To locate the handset using this feature, press and holdMute Handset LocatorOperating Range Changing ChannelsSpeaker Volume Control Setting the ClockAnswering System SET-UP Turning the System On/OffAnnouncement Options General AnnouncementsSelecting Your General Announcement For exampleCaller Specific Announcements Recording Your General AnnouncementDeleting Your General Announcement Setting Up Caller Specific Outgoing Announcements OutgoingFeature Set-Up Announcement Play/SilentAudible Message Alert Remote Access CodeRing Select and Toll Saver Priority Call Signal Base Ringer SettingReviewing Feature Settings Changing the Priority Calling CodeAnswering System Operation Answering CallsCall Screening/Intercept Announcement BypassListening to Your Messages Saving Messages Deleting MessagesDelete all messages in a mailbox Delete selected messagesMessage Guard Power Fail Protection System Recording a MemoConnecting with the Answering System Voice Help MenuFrom the Cordless Handset From a Touch Tone PhoneConnect with the answering system Remote Access CommandsPlaying messages Call Screening Changing Outgoing AnnouncementReviewing Your Announcement To monitor a callRecording a Message When System is Off Remote On/OffReview ON/OFF Status Turning System OffExit Remote Access Changing SettingsReviewing Settings Handset Batteries Charging the Handset Battery PackReplacing the Handset Battery Pack Replacing the Base Power Reserve Batteries Base Unit BACK-UP BatteriesSignals and Displays Audible SignalsCase of Difficulty If the phone does not work at all, check these items firstIf you hear noise or interference when using the phone If the phone does not ring when you receive a callIf you hear other calls while using the phone If you have no dial toneIf you hear noise in the handset and the buttons don’t work If speakerphone conversation sounds distortedIf messages are incomplete If you have difficulty hearing messagesCaller’s name or phone number is not displayed Display Dial feature does not workIf your outgoing announcement isn’t clear Memory Match feature does not work Cordless Digital Answering System Speakerphone End of messages