AT&T 7720 user manual Wall Installation

Page 11

INSTALLATION

Wall Installation

The wall mounting bracket is a wedge-shaped plastic piece attached to the bottom of the base. You’ll need to attach this piece so the thickest end of the bracket is facing the floor when you wall-mount the base.

1Follow Steps 1–4 in “Table/Desk Installation,” except do not reattach the mounting bracket.

2Connect the power cord to the telephone.

Plug the power cord into the jack labeled POWER on the back of the base.

3Guide the power cord from the jack through the straight channel on the base.

Let the excess cord extend straight out of the end of the channel that is farthest from the jack.

4Connect the telephone line cord.

Plug one end of the telephone line cord into the jack on the base. Guide the cord from the jack through the curved channel on the bottom of the base. Wrap any excess line cord around the two crescent-shaped tabs on the underside of the wall-mounting bracket. (Make sure you leave enough cord free to extend to the wall jack.)

5Feed the free end of the line cord through the rectangular opening in the center of the bracket.

6Replace the bracket.

Place the bracket back on the base so that the thicker end will be at the bottom of the base when wall-mounted.

7Connect the line cord to the wall jack. Make sure it snaps firmly into place.

8Mount the base on the wall.

Hold the base so the mounting knobs on the wall plate fit the keyhole slots on the base. Slide the base down onto the knobs until it locks into place.

9Plug the AC adapter on the power cord into an electrical outlet not controlled by a wall switch.

CAUTION: Use only the AC power adapter supplied with this

telephone. Power Supply HADW-1; Input: 120V AC, 60 Hz, 16W;

Output: 12V DC, 900mA.

NOTE: When the system is first connected to AC power, it begins an automatic initialization routine. After this routine is complete, the Message Counter flashes CL, indicating the clock needs to be set. See “Setting the Clock” in the ANSWERING SYSTEM SET-UP section of this manual.

9

Image 11

Contents User’s Manual for Digital Answering System Philips Consumer Communications L.P. All rights reserved Table of Contents Table of Contents Handset Batteries Installation Installation Set the handset Ringer switch Table/Desk InstallationInstall the handset battery Connect the telephone line cord Install the power reserve batteriesCheck for a dial tone Connect the power cordSet the dial mode Wall Installation Follow Steps 7 to 12 in Table/Desk Installation Telephone Operation Temporary Tone FlashRedial Voice SecurityPaging someone at the base from the handset Answering a call while using the intercomHold Page/IntercomRecording a Phone Conversation Power Reserve FeatureCall Waiting Caller IDAbout Caller Identification To program your local area codes Caller ID SET UPProgramming Local Area Codes Call List Options Turn Off Caller ID with Call WaitingRecording Call Announcements Caller ID FeaturesNew Call Indicator Call AnnounceReviewing Call History Reviewing and Deleting Call AnnouncementsIncoming Call History Caller ID Display Messages Display DialRemoving Call Records from History Removing All Call RecordsStoring a Pause in a Memory Number Memory Guard FeatureTelephone Memory Storing Numbers in MemoryDialing Memory Numbers Storing a Name with a NumberMemory Match Viewing Numbers in MemoryStoring a Number from Call History in Telephone Memory Storing a Number Just Dialed in Telephone MemoryReplacing a Stored Number Priority Ring NumbersHandset Locator Speakerphone Volume ControlTo locate the handset using this feature, press and hold MuteChanging Channels Operating RangeTurning the System On/Off Speaker Volume ControlSetting the Clock Answering System SET-UPFor example Announcement OptionsGeneral Announcements Selecting Your General AnnouncementCaller Specific Announcements Recording Your General AnnouncementDeleting Your General Announcement Outgoing Setting Up Caller Specific Outgoing AnnouncementsAnnouncement Play/Silent Feature Set-UpAudible Message Alert Remote Access CodeRing Select and Toll Saver Changing the Priority Calling Code Priority Call SignalBase Ringer Setting Reviewing Feature SettingsAnnouncement Bypass Answering System OperationAnswering Calls Call Screening/InterceptListening to Your Messages Delete selected messages Saving MessagesDeleting Messages Delete all messages in a mailboxRecording a Memo Message Guard Power Fail Protection SystemFrom a Touch Tone Phone Connecting with the Answering SystemVoice Help Menu From the Cordless HandsetConnect with the answering system Remote Access CommandsPlaying messages To monitor a call Call ScreeningChanging Outgoing Announcement Reviewing Your AnnouncementTurning System Off Recording a Message When System is OffRemote On/Off Review ON/OFF StatusExit Remote Access Changing SettingsReviewing Settings Handset Batteries Charging the Handset Battery PackReplacing the Handset Battery Pack Base Unit BACK-UP Batteries Replacing the Base Power Reserve BatteriesAudible Signals Signals and DisplaysIf the phone does not work at all, check these items first Case of DifficultyIf you have no dial tone If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you hear other calls while using the phoneIf you have difficulty hearing messages If you hear noise in the handset and the buttons don’t workIf speakerphone conversation sounds distorted If messages are incompleteCaller’s name or phone number is not displayed Display Dial feature does not workIf your outgoing announcement isn’t clear Memory Match feature does not work Cordless Digital Answering System Speakerphone End of messages