AT&T 7720 user manual Connect the power cord, Check for a dial tone, Set the dial mode

Page 10

INSTALLATION

6Connect the power cord.

Plug the power cord into the jack labeled POWER on the back of the base. Plug the AC adapter on the power cord into an electrical outlet not controlled by a wall switch.

CAUTION: Use only the AC power adapter supplied with this

telephone. Power Supply HADW-1; Input: 120V AC, 60 Hz, 16W;

Output: 12V DC, 900mA.

NOTE: When the system is first connected to AC power, it begins an automatic initialization routine. After this routine is complete, the Message Counter flashes CL, indicating the clock needs to be set. See “Setting the Clock” in the ANSWERING SYSTEM SET-UP section of this manual.

7Rotate the base antenna so it is fully upright.

8Charge the handset batteries before use.

Place the handset in the base and charge the batteries for four hours. The CHARGING light on the base goes on to show the handset is in the right position to charge the batteries. The handset will charge when placed in the cradle either face up or face down.

9Check for a dial tone.

After the batteries are charged, pick up the handset. Check for a dial tone by pressing P; the PHONE light should go on and you should hear a dial tone. Press Pagain to turn the phone off.

10Set the dial mode.

If you have touch tone service, the phone will be ready to use as soon as the battery is charged.

If you have dial pulse service you will need to set the dial mode as follows:

a Press Uon the handset.

b Use the softkey to select NEXT. (See “About Softkeys” in the TELEPHONE OPERATION section of this manual.)

c Use the softkey to select SETUP.

d Use the softkey and continue to select NEXT until the screen displays DIAL MODE:TONE.

e Use the softkey to select CHANGE. The screen displays DIAL MODE:PULSE.

f Press Uto exit.

To change back to tone dialing, follow Steps a through d.

11Follow the instructions in the CALLER ID SET-UP section of this manual.

12Follow the instructions in the ANSWERING SYSTEM SET-UP section of this manual.

8

Image 10

Contents User’s Manual for Digital Answering System Philips Consumer Communications L.P. All rights reserved Table of Contents Table of Contents Handset Batteries Installation Installation Install the handset battery Table/Desk InstallationSet the handset Ringer switch Install the power reserve batteries Connect the telephone line cordSet the dial mode Connect the power cordCheck for a dial tone Wall Installation Follow Steps 7 to 12 in Table/Desk Installation Telephone Operation Voice Security FlashRedial Temporary TonePage/Intercom Answering a call while using the intercomHold Paging someone at the base from the handsetPower Reserve Feature Recording a Phone ConversationAbout Caller Identification Caller IDCall Waiting Programming Local Area Codes Caller ID SET UPTo program your local area codes Turn Off Caller ID with Call Waiting Call List OptionsCall Announce Caller ID FeaturesNew Call Indicator Recording Call AnnouncementsIncoming Call History Reviewing and Deleting Call AnnouncementsReviewing Call History Removing All Call Records Display DialRemoving Call Records from History Caller ID Display MessagesStoring Numbers in Memory Memory Guard FeatureTelephone Memory Storing a Pause in a Memory NumberViewing Numbers in Memory Storing a Name with a NumberMemory Match Dialing Memory NumbersPriority Ring Numbers Storing a Number Just Dialed in Telephone MemoryReplacing a Stored Number Storing a Number from Call History in Telephone MemoryMute Speakerphone Volume ControlTo locate the handset using this feature, press and hold Handset LocatorOperating Range Changing ChannelsAnswering System SET-UP Speaker Volume ControlSetting the Clock Turning the System On/OffSelecting Your General Announcement Announcement OptionsGeneral Announcements For exampleDeleting Your General Announcement Recording Your General AnnouncementCaller Specific Announcements Setting Up Caller Specific Outgoing Announcements OutgoingFeature Set-Up Announcement Play/SilentRing Select and Toll Saver Remote Access CodeAudible Message Alert Reviewing Feature Settings Priority Call SignalBase Ringer Setting Changing the Priority Calling CodeCall Screening/Intercept Answering System OperationAnswering Calls Announcement BypassListening to Your Messages Delete all messages in a mailbox Saving MessagesDeleting Messages Delete selected messagesMessage Guard Power Fail Protection System Recording a MemoFrom the Cordless Handset Connecting with the Answering SystemVoice Help Menu From a Touch Tone PhonePlaying messages Remote Access CommandsConnect with the answering system Reviewing Your Announcement Call ScreeningChanging Outgoing Announcement To monitor a callReview ON/OFF Status Recording a Message When System is OffRemote On/Off Turning System OffReviewing Settings Changing SettingsExit Remote Access Replacing the Handset Battery Pack Charging the Handset Battery PackHandset Batteries Replacing the Base Power Reserve Batteries Base Unit BACK-UP BatteriesSignals and Displays Audible SignalsCase of Difficulty If the phone does not work at all, check these items firstIf you hear other calls while using the phone If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you have no dial toneIf messages are incomplete If you hear noise in the handset and the buttons don’t workIf speakerphone conversation sounds distorted If you have difficulty hearing messagesIf your outgoing announcement isn’t clear Display Dial feature does not workCaller’s name or phone number is not displayed Memory Match feature does not work Cordless Digital Answering System Speakerphone End of messages