BT 106 To connect up to 6 master extension sockets, Install the required number Extension sockets

Page 8

Ultimate 106 – Edition 1 – Issue 3 - 18.12.02 – 5129

To connect up to 6 master extension sockets

IMPORTANT

You must connect your extensions to a MASTER telephone socket. You can purchase master sockets and wiring kits from any good electrical retailer.

Install the required number of

1 extension sockets

In your Wiring Kit you will find the white socket(s) and a disposable insertion tool.

You will need to decide how you wish to fix the extension socket and how the cable will be run into it.

Push out the plastic ‘holes’ in the backbox that correspond with where you wish the cables to run.

Screw the backbox of your extension socket onto the skirting board or wall using the screws provided.

Now strip off approximately 5 cms (about 2 ins) of outer sheath from the extension cable. The colour-coded covering on the wires in the cable should not be stripped.

Run the required cable length to your

Ultimate 106. Attach the cable firmly to the wall.

Connector 1

 

 

 

Connector 6

Connector 2

 

 

 

Connector 5

 

 

Connector 3

 

 

 

Connector 4

Thread the plastic wire grip through the socket (as shown above).

The telephone extension cable contains 4 strands of wire, 2 with broad orange, or blue stripes, 2 with narrow orange or blue stripes.

Choose a pair of wires of the same colour, for instance the broad blue stripes and the narrow blue strips.

Then, holding the insertion tool, as shown, simply push the wires firmly into connection 2 and 5. The broad blue stripes into connector 2, the narrow blue stripes to connector 5. Secure the cable with the cable grip.

6

Image 8
Contents User Guide UltimateKey features At a glance For your records Personal Emergency NumbersContents Introduction Unpacking your UltimateInstallation Wall mounting the Ultimate Extension numbersInstall the required number Extension sockets To connect up to 6 master extension socketsConnect the extension sockets to the Ultimate Remove the lower cover from the UltimateConnect the power cable Connect the telephone line cordSystem settings To make any system settingsTime and date settings Time is 3.15pmMonday February 27th To set the timeTo set the ring delay Extension ring delay Day and night modesRing delay is 3 rings and day mode To select which extensions ring during the night To select which extensions ring during the dayTo stop extensions from ringing during the day Day mode start 830 a.m Night mode start 6pmCall barring Creating a hotline numberExample Extension 12 barring is level Example Extension 12 is set for hotlineExtension 12 is set for normal Connecting a payphoneExtension 12 is set for payphone Connecting a fax machine Resetting the systemCall Sign on, delay off Call Sign on, delay onAnnounce System reset Playing music to callers on holdTo select answering machine mode Answering MachineCall Director To set-up Answering MachineAnnounces Answering delay is set Answering delay is two ringsAnswering delay is six rings Answering delay is nine ringsTo set up Call Director Announces Call Director is setAnnounces Call Director is on Announces Call Director is offRecord your call director message after the tone To record a Call Director OGMTo replay the Call Director OGM Call Director, example OGMsPush square to confirm Playing back your messagesYour messages To hear how much recording time is remaining To program your PINTo operate your Answering Machine from another telephone Using your phone extensions Making and receiving callsTo put a call on hold To hold a 3-way callTo transfer a call between extensions To forward calls to another extensionAlarm on am Alarm clearedAnnounces Extension divert is off Announces Extension do not disturb is setUsing your Ultimate 106 as a Room Monitor Using RingbackRingback Extension X or Ringback To set the Room MonitorIntercom Ring a telephone number Using the speed dial memoryEnter 2 digit location and number To store the last dialled call as a speed dial number To dial a speed dial numberUsing BT Select Services Using Caller IdentificationTo review calling numbers To screen incoming calls using Caller IdentificationTo set the Caller Identification options at each extension To switch between 2 callers BT’s Call Waiting serviceTo use BT’s Call Waiting service Maintenance ServiceWall mounting To wall mount the Ultimate 106 base unitAre you in the correct programming mode i.e. program/normal HelpTechnical information DtmfUltimate 106 default settings Normal modeGlobal programming mode Index OGM Offices worldwide Ultimate 106 Wall Mounting Template
Related manuals
Manual 42 pages 47.06 Kb