Lincoln Electric SVM 113-A service manual These Devices Without

Page 14

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

A-8

A-8

INSTALLATION

CAUTION

Certain Electrical devices cannot be powered by the WELDANPOWER 125. See Table A.2.

TABLE A.2

ELECTRICAL DEVICE USE WITH THE WELDANPOWER 125.

Type

Common Electrical Devices

Possible Concerns

 

 

 

Resistive

Heaters, toasters, incandescent

NONE

 

light bulbs, electric range, hot

 

 

pan, skillet, coffee maker.

 

 

 

 

Capacitive

TV sets, radios, microwaves,

Voltage spikes or high voltage

 

appliances with electrical control.

regulation can cause the capac-

 

 

itative elements to fail. Surge

 

 

protection, transient protection,

 

 

and additional loading is recom-

 

 

mended for 100% fail-safe

 

 

operation. DO NOT RUN

 

 

THESE DEVICES WITHOUT

 

 

ADDITIONAL RESISTIVE TYPE

 

 

LOADS.

 

 

 

Inductive

Single-phase induction motors,

These devices require large

 

drills, well pumps, grinders, small

current inrush for starting. (See

 

refrigerators, weed and hedge

Table B.3, GENERATOR POWER

 

trimmers.

APPLICATIONS, in the

 

 

Operation section of this manu-

 

 

al for required starting

 

 

wattages.) Some synchronous

 

 

motors may be frequency sensi-

 

 

tive to attain maximum output

 

 

torque, but they SHOULD BE

 

 

SAFE from any frequency

 

 

induced failures.

 

 

 

Capacitive/Inductive

Computers, high resolution TV sets,

An inductive type line condition-

 

complicated electrical equipment.

er along with transient and

 

 

surge protection is required, and

 

 

liabilities still exist. DO NOT

 

 

USE THESE DEVICES WITH A

 

 

WELDANPOWER 125.

 

 

 

The Lincoln Electric Company is not responsible for any damage to electrical components improperly connected to the WELDANPOWER 125.

WELDANPOWER 125

Image 14
Contents Weldanpowertm Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications WeldanpowerStoring Safety PrecautionsLocation and Ventilation PRE-OPERATION Engine Service Electrical Output Connections Welding Cable ConnectionsPlugs and HAND-HELD Equipment Auxiliary Power ReceptaclesMachine Grounding Premises Wiring Circuit BreakersThese Devices Without Table of Contents Operation Section Operating Instructions Safety InstructionsOperation General DescriptionRecommended Applications Operational Features and ControlsDesign Features Advantages Welding CapabilityControls and Settings WELDER/GENERATOR ControlsGasoline Engine Controls Figure B.2 Gasoline Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine Stopping the Engine For Best Engine StartingGeneral Information Welding OperationBREAK-IN Period LOW OIL SensingTo USE the Weldanpower 125 for WELD- ING TIG WeldingTable B.2 Electrode Selection Guide Auxiliary Power To USE the Weldanpower 125 AS AN Auxiliary Power SupplyTable B.3 Generator Power Applications Table of Contents Accessories Briggs and Stratton Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Routine and Periodic Maintenance Engine MaintenanceFigure D.3 Clean Finger Guard MaintanenceFigure D.5 SET Spark Plug GAP WELDER/GENERATOR Maintenance Table D.2 Engine Maintenance PartsFigure D.6 Major Component Locations Table of Contents Theory of Operation Section ENGINE, EXCITATION, Rotor and Stator Idler BoardRotor Field Feedback Auxiliary Power Engine Idle Control Auxiliary Power Overcurrent ProtectionWeld WINDING, Output Rectifier and Choke Figure E.4 Weld WINDING, Output Rectifier and ChokeTable of Contents Trouble Shooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Electric Shock can killTroubleshooting Guide Output ProblemsOutput Rectifier Troubleshooting & Repair Perform the Engine Throttle Engine Problems Main Stator Winding Test Engine Throttle Adjustment Troubleshooting & Repair Weldanpower Materials Needed Rotor Voltage TestTest Description Test Procedure Rotor Voltage TestRotor Resistance Test Rotor Resistance Test Figure F.3 Brushes Retained with Cable TIE Output Rectifier Bridge Test Output Rectifier Bridge Test Main Stator Test Main Stator Test Figure F.6 Main Stator Molex Plug Test Points Rotor Flashing Circuit Test Rotor Flashing Circuit Test WP125 Idler Engine Throttle Adjustment Test Test Procedure Figure F.12 Idle Speed Adjustment Screw Locations Figure F.13 LOW Idle Adjustment NUT on Idler Solenoid TOC High Idle no Load Output Control AT Maximum Scope SettingsNormal Open Circuit Weld Voltage Waveform Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded to 125 Amps AT 25 VAC Typical Weld Output WaveformMachine Loaded Abnormal Open Circuit Weld Voltage Waveform Brush Removal and Replacement DescriptionProcedure Figure F.14 Brushes Retained with Cable TIEProcedure Rheostat Removal and Replacement Rheostat Removal and Replacement Field Capacitor Removal and Replacement Field Capacitor Removal and Replacement Field Diode Bridge Removal and Replacement Field Diode Bridge Removal and Replacement Figure F.18 Field Diode Bridge Location Idler Printed Circuit Board Removal Replacement Carefully remove the board Output Rectifier Bridge Removal Replacement Output Rectifier Bridge Removal and Replacement Troubleshooting & Repair Output Choke Removal and Replacement Output Choke Removal and Replacement Section TOC STATOR/ROTOR Removal and Replacement InstructionsStator Removal Procedure Troubleshooting & Repair Rotor Removal Procedure Reassembly ProcedureFigure F.24 Checking ROTOR-STATOR AIR GAP Feeler Gauge Troubleshooting & Repair Engine Output Auxiliary Power Receptacle OUTPUT1Retest After Repair WELDER/GENERATOR OUTPUT1Weldanpower Table of Contents Diagrams Section Wiring Diagram Code 10158 Idler PC Board M17578 DiagramsSchematic Dimension Print Weldanpower Weldanpower M17578 Idler PC Board M17578-1M17578 Idler PC Board Bill of Materials DescriptionWeldanpower