Lincoln Electric SVM 113-A service manual Procedure, Figure F.14 Brushes Retained with Cable TIE

Page 74

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

F-36

F-36

TROUBLESHOOTING & REPAIR

BRUSH REMOVAL AND REPLACEMENT (continued)

FIGURE F.14 - BRUSHES RETAINED WITH CABLE TIE

CABLE

TIE

BRUSHES

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

PROCEDURE

1.Remove the spark plug wire.

2.Open the brush holder assembly cover. Squeeze the 2 tabs and depress the cover at the top with a screw driver or your fin- gernail. The cover will drop open on its bottom hinge.

3.With the 1/4” nut driver, remove the 2 screws that hold the brush holder assem- bly in place.

4.With the needle nose pliers, gently remove the black and the red wires.

Note: The red wire is inboard. “RED” is marked on the brush holder beside the termi- nal for the red wire.

5.To change the brushes, use the slot head screw driver to pop off the plastic retainer on the back of the brush holder assembly.

6.Remove the old brush assemblies and insert the new ones. One corner of the ter- minal clip is beveled so that the brush can go in only one way.

7.Snap the plastic retainer back onto the brush holder. The brushes may need some repositioning; wiggle them slightly to help them seat properly on the slip rings.

WELDANPOWER 125

Image 74

Contents Weldanpowertm Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications WeldanpowerStoring Safety PrecautionsLocation and Ventilation PRE-OPERATION Engine Service Electrical Output Connections Welding Cable ConnectionsPlugs and HAND-HELD Equipment Auxiliary Power ReceptaclesMachine Grounding Premises Wiring Circuit BreakersThese Devices Without Table of Contents Operation Section Operating Instructions Safety InstructionsOperation General DescriptionRecommended Applications Operational Features and ControlsDesign Features Advantages Welding CapabilityControls and Settings WELDER/GENERATOR ControlsGasoline Engine Controls Figure B.2 Gasoline Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine Stopping the Engine For Best Engine StartingGeneral Information Welding OperationBREAK-IN Period LOW OIL SensingTo USE the Weldanpower 125 for WELD- ING TIG WeldingTable B.2 Electrode Selection Guide Auxiliary Power To USE the Weldanpower 125 AS AN Auxiliary Power SupplyTable B.3 Generator Power Applications Table of Contents Accessories Briggs and Stratton Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Routine and Periodic Maintenance Engine MaintenanceFigure D.3 Clean Finger Guard MaintanenceFigure D.5 SET Spark Plug GAP WELDER/GENERATOR Maintenance Table D.2 Engine Maintenance PartsFigure D.6 Major Component Locations Table of Contents Theory of Operation Section ENGINE, EXCITATION, Rotor and Stator Idler BoardRotor Field Feedback Auxiliary Power Engine Idle Control Auxiliary Power Overcurrent ProtectionWeld WINDING, Output Rectifier and Choke Figure E.4 Weld WINDING, Output Rectifier and ChokeTable of Contents Trouble Shooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Electric Shock can killTroubleshooting Guide Output ProblemsOutput Rectifier Troubleshooting & Repair Perform the Engine Throttle Engine Problems Main Stator Winding Test Engine Throttle Adjustment Troubleshooting & Repair Weldanpower Materials Needed Rotor Voltage TestTest Description Test Procedure Rotor Voltage TestRotor Resistance Test Rotor Resistance Test Figure F.3 Brushes Retained with Cable TIE Output Rectifier Bridge Test Output Rectifier Bridge Test Main Stator Test Main Stator Test Figure F.6 Main Stator Molex Plug Test Points Rotor Flashing Circuit Test Rotor Flashing Circuit Test WP125 Idler Engine Throttle Adjustment Test Test Procedure Figure F.12 Idle Speed Adjustment Screw Locations Figure F.13 LOW Idle Adjustment NUT on Idler Solenoid TOC High Idle no Load Output Control AT Maximum Scope SettingsNormal Open Circuit Weld Voltage Waveform Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded to 125 Amps AT 25 VAC Typical Weld Output Waveform Machine Loaded Abnormal Open Circuit Weld Voltage Waveform Brush Removal and Replacement DescriptionProcedure Figure F.14 Brushes Retained with Cable TIEProcedure Rheostat Removal and Replacement Rheostat Removal and Replacement Field Capacitor Removal and Replacement Field Capacitor Removal and Replacement Field Diode Bridge Removal and Replacement Field Diode Bridge Removal and Replacement Figure F.18 Field Diode Bridge Location Idler Printed Circuit Board Removal Replacement Carefully remove the board Output Rectifier Bridge Removal Replacement Output Rectifier Bridge Removal and Replacement Troubleshooting & Repair Output Choke Removal and Replacement Output Choke Removal and Replacement Section TOC STATOR/ROTOR Removal and Replacement InstructionsStator Removal Procedure Troubleshooting & Repair Rotor Removal Procedure Reassembly ProcedureFigure F.24 Checking ROTOR-STATOR AIR GAP Feeler Gauge Troubleshooting & Repair Engine Output Auxiliary Power Receptacle OUTPUT1Retest After Repair WELDER/GENERATOR OUTPUT1Weldanpower Table of Contents Diagrams Section Wiring Diagram Code 10158 Idler PC Board M17578 DiagramsSchematic Dimension Print Weldanpower Weldanpower M17578 Idler PC Board M17578-1M17578 Idler PC Board Bill of Materials DescriptionWeldanpower