Lincoln Electric SVM 113-A service manual Weldanpower

Page 50

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-12

F-12

TROUBLESHOOTING & REPAIR

TROUBLESHOOTING & REPAIR

TROUBLESHOOTING GUIDE

 

Observe Safety Guidelines

 

detailed in the beginning of this manual.

 

 

 

 

 

PROBLEMS

POSSIBLE AREAS OF

RECOMMENDED

 

 

(SYMPTOMS)

MISADJUSTMENT(S)

COURSE OF ACTION

 

 

 

 

 

 

 

 

ENGINE PROBLEMS

 

 

 

 

The welding arc is “cold.” The

1. Check for loose or faulty con-

1. With the output control at max-

engine runs normally. The auxiliary

nections at the weld output ter-

imum, check for the correct

power functions normally.

minals and welding cable con-

open circuit voltage (OCV) at

 

nections.

the welder output terminals (75

 

2. The welding cable may be too

- 82 VDC). If the correct open

 

circuit voltage is present at the

 

long or coiled, causing an

 

output

terminals,

check

for

 

excessive voltage drop.

 

loose connections on the heavy

 

 

 

 

current carrying leads inside the

 

 

WELDANPOWER

125.

See

 

 

Wiring Diagram.

 

 

 

 

2. If the OCV is low at the welder

 

 

output

terminals,

perform

the

 

 

Engine

Throttle

Adjustment

 

 

Test.

 

 

 

 

 

3. Perform the Output Rectifier

 

 

Bridge Test.

 

 

 

 

4. Check for shorted or grounded

 

 

windings in the choke (L1).

 

 

 

 

 

 

 

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con- tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call 216-383-2531 or 1-800-833-9353.

WELDANPOWER 125

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Weldanpowertm Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications WeldanpowerStoring Safety PrecautionsLocation and Ventilation PRE-OPERATION Engine Service Electrical Output Connections Welding Cable ConnectionsPlugs and HAND-HELD Equipment Auxiliary Power ReceptaclesMachine Grounding Premises Wiring Circuit BreakersThese Devices Without Table of Contents Operation Section Operating Instructions Safety InstructionsOperation General DescriptionRecommended Applications Operational Features and ControlsDesign Features Advantages Welding CapabilityControls and Settings WELDER/GENERATOR ControlsGasoline Engine Controls Figure B.2 Gasoline Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine Stopping the Engine For Best Engine StartingGeneral Information Welding OperationBREAK-IN Period LOW OIL SensingTo USE the Weldanpower 125 for WELD- ING TIG WeldingTable B.2 Electrode Selection Guide Auxiliary Power To USE the Weldanpower 125 AS AN Auxiliary Power SupplyTable B.3 Generator Power Applications Table of Contents Accessories Briggs and Stratton Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Routine and Periodic Maintenance Engine MaintenanceFigure D.3 Clean Finger Guard MaintanenceFigure D.5 SET Spark Plug GAP WELDER/GENERATOR Maintenance Table D.2 Engine Maintenance PartsFigure D.6 Major Component Locations Table of Contents Theory of Operation Section ENGINE, EXCITATION, Rotor and Stator Idler BoardRotor Field Feedback Auxiliary Power Engine Idle Control Auxiliary Power Overcurrent ProtectionWeld WINDING, Output Rectifier and Choke Figure E.4 Weld WINDING, Output Rectifier and ChokeTable of Contents Trouble Shooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Electric Shock can killTroubleshooting Guide Output ProblemsOutput Rectifier Troubleshooting & Repair Perform the Engine Throttle Engine Problems Main Stator Winding Test Engine Throttle Adjustment Troubleshooting & Repair Weldanpower Materials Needed Rotor Voltage TestTest Description Test Procedure Rotor Voltage TestRotor Resistance Test Rotor Resistance Test Figure F.3 Brushes Retained with Cable TIE Output Rectifier Bridge Test Output Rectifier Bridge Test Main Stator Test Main Stator Test Figure F.6 Main Stator Molex Plug Test Points Rotor Flashing Circuit Test Rotor Flashing Circuit Test WP125 Idler Engine Throttle Adjustment Test Test Procedure Figure F.12 Idle Speed Adjustment Screw Locations Figure F.13 LOW Idle Adjustment NUT on Idler Solenoid TOC High Idle no Load Output Control AT Maximum Scope SettingsNormal Open Circuit Weld Voltage Waveform Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded to 125 Amps AT 25 VAC Typical Weld Output WaveformMachine Loaded Abnormal Open Circuit Weld Voltage Waveform Brush Removal and Replacement DescriptionProcedure Figure F.14 Brushes Retained with Cable TIEProcedure Rheostat Removal and Replacement Rheostat Removal and Replacement Field Capacitor Removal and Replacement Field Capacitor Removal and Replacement Field Diode Bridge Removal and Replacement Field Diode Bridge Removal and Replacement Figure F.18 Field Diode Bridge Location Idler Printed Circuit Board Removal Replacement Carefully remove the board Output Rectifier Bridge Removal Replacement Output Rectifier Bridge Removal and Replacement Troubleshooting & Repair Output Choke Removal and Replacement Output Choke Removal and Replacement Section TOC STATOR/ROTOR Removal and Replacement InstructionsStator Removal Procedure Troubleshooting & Repair Rotor Removal Procedure Reassembly ProcedureFigure F.24 Checking ROTOR-STATOR AIR GAP Feeler Gauge Troubleshooting & Repair Engine Output Auxiliary Power Receptacle OUTPUT1Retest After Repair WELDER/GENERATOR OUTPUT1Weldanpower Table of Contents Diagrams Section Wiring Diagram Code 10158 Idler PC Board M17578 DiagramsSchematic Dimension Print Weldanpower Weldanpower M17578 Idler PC Board M17578-1M17578 Idler PC Board Bill of Materials DescriptionWeldanpower
Top Page Image Contents