Lincoln Electric IM892-C manual Smaw Stick Welding Display, MSP4 Operation, Process Mode

Page 24

		OPERATION
B-8		OPERATION	B-8

SMAW (Stick) Welding Display

FIGURE B.3

194

WFS AMPS

0n

VOLTS TRIM

LESS	MORE	OUTPUT	OUTPUT
AMPS	AMPS	OFF	ON

MSP4 OPERATION

CCSTICK MODES

PROCESS MODE

Stick	Soft(7018)	1
Stick	Crisp(6010)	2

START OPTIONS


	START TIME:	FUNCTION
	START TIME:	FUNCTION
	0 to 10 seconds	If no remote control is installed,
		this control sets the time for
		the weld output to ramp up or
		down from a preset Start cur-
		rent to the preset Weld current.
		Use the WFS/ AMP kno b to
		adjust Start current while the
		Start Options LED is displayed.

WAVEFORM CONTROL TECHNOLOGY

IR PORT

IStick

I

	SETUP
	CC Stick Soft
WELD MODE	START OPTIONS
ARC CONTROL	END OPTIONS
	SET


	ARC CONTROL
ARC FORCE		DESCRIPTION
(Soft)-10.0 to		Lower values will provide less short
(Crisp)+10.0		circuit current and a softer arc.
		Higher settings will provide a higher
		short circuit current, a more forceful
		arc and possibly more spatter.

END OPTIONS

No arc ending options are active for SMAW (Stick) welding modes.

POWER FEED™ 25M

Image 24

Contents Power Feed 25M Safety Electric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Please Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTable of Contents Gearing WFS Range Wire Sizes Height Width Depth WeightPower Feed 25M Input Voltage ± 10% Input AmperesSafety Precautions LocationHigh Frequency Protection Electric Shock can KillArclink Control Cables Cable ConnectionsPIN To install Weld Cable SizeCoaxial Weld Cable Table A.1Electrode Polarity Shielding GAS ConnectionBuild UP of Shielding GAS MAY Harm Health or Kill Changing the Drive Motor Gear Ratio OFFWire Drive Configuration Procedure to Install Drive Rolls and Wire GuidesRemote Sense Lead Specifications Loading Spools of WireTypical System Configurations Direct Current Open CircuitVoltage Input VoltageDefinition of Welding Terms Duty CycleRecommended Power Sources Recommended ProcessesEquipment Limitations Case Front Controls Code See Figure B.1Case Front Controls Code 11456 ON-OFF Switch Status LEDTable B.1 DefinitionMaking a Weld with Waveform Technology Power Sources Smaw Stick WeldingProcess Mode Smaw Stick Welding DisplayMSP4 Operation NON-SYNERGIC Gmaw and Fcaw Welding Three non-synergic welding modes are availableMSP4 Operation Non-Synergic Gmaw and Fcaw Welding DisplayGmaw MIG Synergic Welding Figure B.5Gmaw MIG Synergic Welding Display Synergic CV Voltage DisplaySteel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC ControlSteel and Stainless Synergic GMAW-P Pulsed MIG Welding 220 Pulse-on-Pulse Welding Figure B.9Aluminum GMAW-P and GMAW-PP Aluminum Pulse WeldingAluminum GMAW-P and GMAW-PP Welding Figure B.14Aluminum Pulse and Pulse-On-Pulse Synergic Weld Display Weld ModesGMAW-STT Welding Figure B.15GMAW-STT Weld ModesPeak Current Figure B.16 Background Current Figure B.17Tailout Gtaw TIG Welding Gtaw Tigwelding Figure B.17a Figure B.17aSET-UP Features Menu Figure B.17b Setup MenuUser Defined Parameters Parameter Definition Procedure Change Method Stall Factor AdjustmentParameter Definition Gun Offset Adjustment Crater DelayReset Consumable Weight TIG Gas Control100 View Diagnostics Parameter Definition Push-Pull Gun Knob BehaviorSense From Studs Show Test Modes107 View Power Source Protocol Parameter Definition 103 View Software Version Information104 View Hardware Version Information 105 View Welding Software InformationParameter Definition 503 Memory Button Disable 504 Mode Select Panel Lock505 Setup Menu Lock 506 Set User Interface PasscodeParameter Definition 507 UI Clear All Memories 509 UI Master LockoutPROCEDURE/MEMORY Panel OPERA- Tion User MemoriesLimits Parameter Range UnitsLimits may be set for MSP4 DisplayHigh Limit Low LimitParameter Name Dual PROCEDURE/MEMORY Operation For Code 11456 and HigherMemory Set Limits 200 Memory ValueInternal Controls for Code DescriptionInternal Controls for Code 11456 and higher EscriptionCold FEED/GAS Purge Switch Light SwitchPressure ARM Adjustment Heater SwitchStep Trigger Operation STEP- Trigger OperationStep Trigger Code 11456 and higherPreflow RUN-INWeld Upslope BurnbackPostflow Start & Upslope CraterCrater & Downslope Figure B.22 Start DownslopeDescription Rear ControlsOperation on Lincnet Power Sources Flow MeterScfh Liter/MinFactory Installed Equipment Wire Type Electrode Size KP KITDrive Roll Kits Used K2593-xx #1 Co-Axial Power Cable K2683-xx Heavy Duty ArcLink Control Cable K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Water Cooled Guns Routine Maintenance Periodic MaintenanceCalibration Specification Troubleshooting Symptoms Description Possible AdjustmentsOutput Problems Troubleshooting Wiring Diagram Power Feed 25M G5585Diagrams Dimensions for Code Dimensions for Codes 11456 Precaucion Warnung