Lincoln Electric IM892-C manual Gmaw MIG Synergic Welding, Figure B.5

Page 27

B-11	OPERATION	B-11

	GMAW (MIG) SYNERGIC WELDING

Synergic welding allows for easy procedure setting. The WFS and Voltage change together to maintain an optimal arc length. During synergic welding , when the WFS (left) knob is rotated, the voltage is adjusted accordingly to maintain a similar arc length.

FIGURE B.5

6

43

1

2

5

	K2368-1	Power Wave® 355M
1	K2202-1	Power Wave® 455M
	K2203-1	Power Wave® 455M/STT
	K2230-1	POWER FEED™ 10M, Bench Model
	K2234-1	POWER FEED™ 10M Dual, Bench Model
	K2536-1,-2,-3	POWER FEED™ 25M
2	KP1696-xx,	Drive Roll Kit, 2 Roll Feeder
	KP1697-xx
	KP1505-xx,	Drive Roll Kit, 4 Roll Feeder
	KP1507-xx
3	K1543-xx	Digital Control Cable
	K2683-xx
4	K1842-xx	Weld Power Cable, Lug to Lug
	K910-xx	Ground Clamp
5	See Magnum®	MIG gun
	Literature
		Deluxe Regulator for Mixed
6	K586-1	Shielding Gases
		Shielding Gas Hose

POWER FEED™ 25M

Image 27

Contents Power Feed 25M Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionPrécautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Input Voltage ± 10% Input Amperes Gearing WFS Range Wire SizesHeight Width Depth Weight Power Feed 25MElectric Shock can Kill Safety PrecautionsLocation High Frequency ProtectionArclink Control Cables Cable ConnectionsPIN Table A.1 To installWeld Cable Size Coaxial Weld CableElectrode Polarity Shielding GAS ConnectionBuild UP of Shielding GAS MAY Harm Health or Kill OFF Changing the Drive Motor Gear RatioProcedure to Install Drive Rolls and Wire Guides Wire Drive ConfigurationLoading Spools of Wire Remote Sense Lead SpecificationsTypical System Configurations Input Voltage Direct CurrentOpen Circuit VoltageDuty Cycle Definition of Welding TermsRecommended Power Sources Recommended ProcessesEquipment Limitations See Figure B.1 Case Front Controls CodeCase Front Controls Code 11456 Definition ON-OFF SwitchStatus LED Table B.1Smaw Stick Welding Making a Weld with Waveform Technology Power SourcesProcess Mode Smaw Stick Welding DisplayMSP4 Operation Three non-synergic welding modes are available NON-SYNERGIC Gmaw and Fcaw WeldingNon-Synergic Gmaw and Fcaw Welding Display MSP4 OperationFigure B.5 Gmaw MIG Synergic WeldingSynergic CV Voltage Display Gmaw MIG Synergic Welding DisplayARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG WeldingSteel and Stainless Synergic GMAW-P Pulsed MIG Welding 220 Figure B.9 Pulse-on-Pulse WeldingAluminum Pulse Welding Aluminum GMAW-P and GMAW-PPFigure B.14 Aluminum GMAW-P and GMAW-PP WeldingWeld Modes Aluminum Pulse and Pulse-On-Pulse Synergic Weld DisplayFigure B.15 GMAW-STT WeldingWeld Modes GMAW-STTPeak Current Figure B.16 Background Current Figure B.17Tailout Gtaw TIG Welding Figure B.17a Gtaw Tigwelding Figure B.17aFigure B.17b Setup Menu SET-UP Features MenuUser Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change MethodTIG Gas Control Parameter Definition Gun Offset AdjustmentCrater Delay Reset Consumable WeightShow Test Modes 100 View DiagnosticsParameter Definition Push-Pull Gun Knob Behavior Sense From Studs105 View Welding Software Information 107 View Power Source ProtocolParameter Definition 103 View Software Version Information 104 View Hardware Version Information506 Set User Interface Passcode Parameter Definition 503 Memory Button Disable504 Mode Select Panel Lock 505 Setup Menu Lock509 UI Master Lockout Parameter Definition 507 UI Clear All MemoriesUser Memories PROCEDURE/MEMORY Panel OPERA- TionMSP4 Display LimitsParameter Range Units Limits may be set forHigh Limit Low LimitParameter Name For Code 11456 and Higher Dual PROCEDURE/MEMORY OperationMemory Set Limits Memory Value 200Description Internal Controls for CodeEscription Internal Controls for Code 11456 and higherHeater Switch Cold FEED/GAS Purge SwitchLight Switch Pressure ARM AdjustmentCode 11456 and higher Step Trigger OperationSTEP- Trigger Operation Step TriggerPreflow RUN-INWeld Upslope BurnbackPostflow Start & Upslope CraterCrater & Downslope Figure B.22 Downslope StartRear Controls DescriptionLiter/Min Operation on Lincnet Power SourcesFlow Meter ScfhFactory Installed Equipment Wire Type Electrode Size KP KITDrive Roll Kits Used K2593-xx #1 Co-Axial Power Cable K2683-xx Heavy Duty ArcLink Control Cable K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Water Cooled Guns Routine Maintenance Periodic MaintenanceCalibration Specification Troubleshooting Description Possible Adjustments SymptomsOutput Problems Troubleshooting G5585 Wiring Diagram Power Feed 25MDiagrams Dimensions for Code Dimensions for Codes 11456 Precaucion Warnung