Lincoln Electric IM892-C manual Preflow, Run-In, Weld

Page 59

B-43	OPERATION	B-43

EXAMPLE 1 - 2 STEP TRIGGER: Simple operation The simplest trigger operation occurs with a 2 Step trigger and the Start, Crater and Burnback functions all set to OFF. (See Figure B.19)

For this sequence,

PREFLOW:

Shielding gas begins to flow immediately when the gun trigger is pulled.

RUN-IN:

After preflow time expires, the power source regulates to the welding output and wire is advanced towards the work piece at the Run-In WFS. If an arc is not established within 1.5 seconds, the wire feed speed will jump to the welding wire feed speed

WELD:

The power source output and the wire feed speed continue at the weld settings for as long as the trigger is pulled.

POSTFLOW: As soon as the trigger is released, the power source output and the wire feed speed are turned OFF. Shielding gas continues until the post flow timer expires.

FIGURE B.19

Trigger Pulled

Arc Established

2 Step Trigger

Start = OFF

Crater = OFF

Burnback = OFF

Trigger Released

Idle	Preflow	Run-In	Weld	Postflow	Idle

Shielding O n

Gas

O ff

	Weld
Power
Source	1.5 sec max.
Output
	O ff

Weld

WFS

Run- in

O ff

POWER FEED™ 25M

Image 59

Contents Power Feed 25M Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionPrécautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Input Voltage ± 10% Input Amperes Gearing WFS Range Wire SizesHeight Width Depth Weight Power Feed 25MElectric Shock can Kill Safety PrecautionsLocation High Frequency ProtectionPIN Arclink Control CablesCable Connections Table A.1 To installWeld Cable Size Coaxial Weld CableBuild UP of Shielding GAS MAY Harm Health or Kill Electrode PolarityShielding GAS Connection OFF Changing the Drive Motor Gear RatioProcedure to Install Drive Rolls and Wire Guides Wire Drive ConfigurationLoading Spools of Wire Remote Sense Lead SpecificationsTypical System Configurations Input Voltage Direct CurrentOpen Circuit VoltageDuty Cycle Definition of Welding TermsEquipment Limitations Recommended Power SourcesRecommended Processes See Figure B.1 Case Front Controls CodeCase Front Controls Code 11456 Definition ON-OFF SwitchStatus LED Table B.1Smaw Stick Welding Making a Weld with Waveform Technology Power SourcesMSP4 Operation Process ModeSmaw Stick Welding Display Three non-synergic welding modes are available NON-SYNERGIC Gmaw and Fcaw WeldingNon-Synergic Gmaw and Fcaw Welding Display MSP4 OperationFigure B.5 Gmaw MIG Synergic WeldingSynergic CV Voltage Display Gmaw MIG Synergic Welding DisplayARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG WeldingSteel and Stainless Synergic GMAW-P Pulsed MIG Welding 220 Figure B.9 Pulse-on-Pulse WeldingAluminum Pulse Welding Aluminum GMAW-P and GMAW-PPFigure B.14 Aluminum GMAW-P and GMAW-PP WeldingWeld Modes Aluminum Pulse and Pulse-On-Pulse Synergic Weld DisplayFigure B.15 GMAW-STT WeldingWeld Modes GMAW-STTTailout Peak Current Figure B.16Background Current Figure B.17 Gtaw TIG Welding Figure B.17a Gtaw Tigwelding Figure B.17aFigure B.17b Setup Menu SET-UP Features MenuUser Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change MethodTIG Gas Control Parameter Definition Gun Offset AdjustmentCrater Delay Reset Consumable WeightShow Test Modes 100 View DiagnosticsParameter Definition Push-Pull Gun Knob Behavior Sense From Studs105 View Welding Software Information 107 View Power Source ProtocolParameter Definition 103 View Software Version Information 104 View Hardware Version Information506 Set User Interface Passcode Parameter Definition 503 Memory Button Disable504 Mode Select Panel Lock 505 Setup Menu Lock509 UI Master Lockout Parameter Definition 507 UI Clear All MemoriesUser Memories PROCEDURE/MEMORY Panel OPERA- TionMSP4 Display LimitsParameter Range Units Limits may be set forParameter Name High LimitLow Limit For Code 11456 and Higher Dual PROCEDURE/MEMORY OperationMemory Set Limits Memory Value 200Description Internal Controls for CodeEscription Internal Controls for Code 11456 and higherHeater Switch Cold FEED/GAS Purge SwitchLight Switch Pressure ARM AdjustmentCode 11456 and higher Step Trigger OperationSTEP- Trigger Operation Step TriggerWeld PreflowRUN-IN Postflow UpslopeBurnback Crater & Downslope Start & UpslopeCrater Figure B.22 Downslope StartRear Controls DescriptionLiter/Min Operation on Lincnet Power SourcesFlow Meter ScfhDrive Roll Kits Used Factory Installed EquipmentWire Type Electrode Size KP KIT K2593-xx #1 Co-Axial Power Cable K2683-xx Heavy Duty ArcLink Control Cable K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Water Cooled Guns Calibration Specification Routine MaintenancePeriodic Maintenance Troubleshooting Description Possible Adjustments SymptomsOutput Problems Troubleshooting G5585 Wiring Diagram Power Feed 25MDiagrams Dimensions for Code Dimensions for Codes 11456 Precaucion Warnung