Lincoln Electric IM892-C manual SET-UP Features Menu, Figure B.17b Setup Menu

Page 41

B-25	OPERATION	B-25

SETUP MENU FEATURES

The Setup Menu gives access to the Setup Configuration. Stored in the setup configuration are user parameters that generally only need to be set at installation. The parameters are grouped as shown in the following table.

PARAMETER	DEFINITION
P.1 through P.99	Unsecured Parameters (always adjustable)
P.101 through P.199	Diagnostic Parameters (always read only)
P.501 through P.599	Secured Parameters (only accessible through a p.c. or palm application)

SET-UP FEATURES MENU

(See Figure B.17b and B.17c for specific Codes)

1.To access the set-up menu, press the Right and Left buttons of the MSP4 panel simultaneously. Note that the set-up menu cannot be accessed if the system is welding, or if there is a fault (The sta- tus LED is not solid green).

Change the value of the blinking parameter by rotat- ing the SET knob.

2.After changing a parameter it is necessary to press the Right hand button to save the new setting. Pressing the Left button will cancel the change.

3.To exit the set-up menu at any time, press the Right and Left buttons of the MSP4 panel simulta- neously. Alternately, 1 minute of inactivity will also exit the set-up menu.

FIGURE B.17b - SETUP MENU

(Only parameters below can be accessed in Code 11313)

P.0	P.7	P.100 thru P.107
P.1	P.8
P.2	P.11
P.3	P.12
P.4	P.13
P.5	P.80
P.6	P.99

Mode Select

Panel (MSP4)

LED

Indicator

	Left	Right
	buttom	Right
	buttom	button
		button
		SET Knob

FIGURE B.17c - SETUP MENU

(All parameters can be accessed in Code 11456 and higher)

Mode Select

Panel (MSP4)

LED

Indicator

	Left	Right
	buttom	Right
	buttom	button
		button
		SET Knob

POWER FEED™ 25M

Image 41

Contents Power Feed 25M Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionPrécautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Height Width Depth Weight Gearing WFS Range Wire SizesPower Feed 25M Input Voltage ± 10% Input AmperesLocation Safety PrecautionsHigh Frequency Protection Electric Shock can KillPIN Arclink Control CablesCable Connections Weld Cable Size To installCoaxial Weld Cable Table A.1Build UP of Shielding GAS MAY Harm Health or Kill Electrode PolarityShielding GAS Connection OFF Changing the Drive Motor Gear RatioProcedure to Install Drive Rolls and Wire Guides Wire Drive ConfigurationLoading Spools of Wire Remote Sense Lead SpecificationsTypical System Configurations Open Circuit Direct CurrentVoltage Input VoltageDuty Cycle Definition of Welding TermsEquipment Limitations Recommended Power SourcesRecommended Processes See Figure B.1 Case Front Controls CodeCase Front Controls Code 11456 Status LED ON-OFF SwitchTable B.1 DefinitionSmaw Stick Welding Making a Weld with Waveform Technology Power SourcesMSP4 Operation Process ModeSmaw Stick Welding Display Three non-synergic welding modes are available NON-SYNERGIC Gmaw and Fcaw WeldingNon-Synergic Gmaw and Fcaw Welding Display MSP4 OperationFigure B.5 Gmaw MIG Synergic WeldingSynergic CV Voltage Display Gmaw MIG Synergic Welding DisplayARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG WeldingSteel and Stainless Synergic GMAW-P Pulsed MIG Welding 220 Figure B.9 Pulse-on-Pulse WeldingAluminum Pulse Welding Aluminum GMAW-P and GMAW-PPFigure B.14 Aluminum GMAW-P and GMAW-PP WeldingWeld Modes Aluminum Pulse and Pulse-On-Pulse Synergic Weld DisplayFigure B.15 GMAW-STT WeldingWeld Modes GMAW-STTTailout Peak Current Figure B.16Background Current Figure B.17 Gtaw TIG Welding Figure B.17a Gtaw Tigwelding Figure B.17aFigure B.17b Setup Menu SET-UP Features MenuUser Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change MethodCrater Delay Parameter Definition Gun Offset AdjustmentReset Consumable Weight TIG Gas ControlParameter Definition Push-Pull Gun Knob Behavior 100 View DiagnosticsSense From Studs Show Test ModesParameter Definition 103 View Software Version Information 107 View Power Source Protocol104 View Hardware Version Information 105 View Welding Software Information504 Mode Select Panel Lock Parameter Definition 503 Memory Button Disable505 Setup Menu Lock 506 Set User Interface Passcode509 UI Master Lockout Parameter Definition 507 UI Clear All MemoriesUser Memories PROCEDURE/MEMORY Panel OPERA- TionParameter Range Units LimitsLimits may be set for MSP4 DisplayParameter Name High LimitLow Limit For Code 11456 and Higher Dual PROCEDURE/MEMORY OperationMemory Set Limits Memory Value 200Description Internal Controls for CodeEscription Internal Controls for Code 11456 and higherLight Switch Cold FEED/GAS Purge SwitchPressure ARM Adjustment Heater SwitchSTEP- Trigger Operation Step Trigger OperationStep Trigger Code 11456 and higherWeld PreflowRUN-IN Postflow UpslopeBurnback Crater & Downslope Start & UpslopeCrater Figure B.22 Downslope StartRear Controls DescriptionFlow Meter Operation on Lincnet Power SourcesScfh Liter/MinDrive Roll Kits Used Factory Installed EquipmentWire Type Electrode Size KP KIT K2593-xx #1 Co-Axial Power Cable K2683-xx Heavy Duty ArcLink Control Cable K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Water Cooled Guns Calibration Specification Routine MaintenancePeriodic Maintenance Troubleshooting Description Possible Adjustments SymptomsOutput Problems Troubleshooting G5585 Wiring Diagram Power Feed 25MDiagrams Dimensions for Code Dimensions for Codes 11456 Precaucion Warnung