Simer Pumps A5000-04 Table IV Error Code Displays LEDs Flashing, Table V Control Button Functions

Page 10

Installation

 

 

10

TABLE IV – Error Code Displays (LEDs Flashing)

 

LED Error Code Display

Error Condition and Corrective Action

 

System Alert

NOTE: When the ‘System Alert’ LED is flashing,

 

look for one of the following error conditions.

Silenced audible alarm

Pump status

Charging

 

AC power

 

Battery status

 

 

 

Condition

Action

 

 

= Excessive battery drain;

Stop pump, allow battery to charge (AC must be on)

 

 

= Battery will not take a charge***;

Replace battery with a new 12V lead-acid battery

 

 

= Reversed battery connections;

Connect + to + and – to –.*

 

 

= Wrong battery voltage;

Replace battery with a new 12V lead-acid battery

 

 

= Failed pre-qualification test – 1**;

Replace battery with a new 12V lead-acid battery

 

 

= Failed pre-qualification test – 2**;

Replace battery with a new 12V lead-acid battery

 

 

= Charge time monitor – 1;

Check battery for damage to cells; replace battery

 

 

= Charge time monitor – 2;

Check battery for damage to cells; replace battery

 

 

= Battery Charge is Below 20%;

Pump will shut down, battery is not charging. Replace

 

 

 

battery.

*NOTE: If your AC power is off and the unit is dead (no LEDs lighted, no audible alarm, pump isn’t running), check for reversed battery connections to the charger/controller.

**Charger was charging at a very low level to try to bring a dead battery back to life, but the battery took too long to charge. Try resetting the charger once or twice (push the ‘System Test’ and ‘Silence Alarm’ buttons at the same time to reset the charger).

***Thermal Runaway condition

= LED is ON Continuously

= LED is Flashing (Fast)

 

 

 

= LED is Flashing (Slow)

= LED is OFF

 

 

 

 

 

 

 

 

5766 0108

TABLE V – Control Button Functions

Control Button:

Result of Pushing Button:

 

 

System Test

Pump starts and all LEDs light up.

 

Will reset the ‘Pump Status’ LED.

 

When pushed with the ‘Silence Alarm’ button, the Charger/Controller

 

microprocessor resets and error code resets.

Silence Alarm

Toggle; Prevents the audible alarm sounding. Press and release to reset.

Flood Light

Toggles the flood light on the Charger/Controller on and off.

 

 

TABLE VI – Capacity Ratings with a 100 A-H Deep Cycle Marine Battery

 

 

VERTICAL PUMPING DISTANCE - MODEL A5000-04

 

8 FEET (2.4 M)

 

10 FEET (3.0 M)

12 FEET (3.7 M)

16 FEET (4.9 M)

Gallons Per Hour

1,440

 

1,200

840

No Flow at this Height

Aproximate Hrs Available

10

 

11.5

13

Total Gallons Pumped

8,500

 

7,000

5,000

 

 

 

 

 

 

*These flow rates were obtained with a constant 12.7 VDC battery source. The actual GPH will vary due to a reduction in output voltage from the battery as it discharges.

For parts or assistance, call Simer Customer Service at 1-800-468-7867 /1-800-546-7867

Image 10
Contents Llame al A5000-04Call 800This is the safety alert symbol. When you see this SafetyRead and Follow Safety Instructions General InformationRequired Battery Capacity InstallationBasic Tools Materials Needed BBU Installation Instructions InstallationEasy Install Layout BBU Wiring and Setup Mark joints for gluingThermal Runaway Condition Wrong Battery VoltageReversed Battery Connections Charge Time Monitor 1Troubleshooting Battery RequirementsBattery Maintenance Table I Battery Capacity CalculationAC power Table III LED Function Displays LEDs Lighted ContinuouslyTable V Control Button Functions Table IV Error Code Displays LEDs FlashingPump status Charging AC power Battery status Control Button Result of Pushing ButtonRepair Parts Part Description Part NumberLire ET Observer LES Instructions DE Sécurité Voici le symbole indiquant quil faut être prudentSécurité Renseignements GénérauxOutils ET Fournitures DE Base Dont on Aura Besoin Capacité requise des batteriesMontage Étudier la pour les montages suggérésInstallation Câblage ET Montage DU Système DE Secours À Batterie Repérer les raccords pour les collerBranchements de la batterie inversés DEL affichées et touches de commande Tableau II, III, IV etRemèdes possibles Claquage thermiqueRecherche DES Pannes Critères DE LA BatterieEntretien DE LA Batterie Tableau 1 Calcul de la capacité de la batterieDEL des codes de fonctionnement Tableau III DEL des fonctions les DEL restent alluméesTableau V Fonctions des touches de contrôle Charging Charge AC power Battery status État de la batterieTableau IV Codes d’erreurs Les DEL clignotent Touches de contrôle RésultatPièces de rechange Réf Désignation des pièces Numéro des piècesInformación General Seguridad¡LEA Y Siga LAS Instrucciones DE Seguridad Este es el símbolo de alerta de seguridad. CuandoHerramientas Y Materiales Básicos Requeridos InstalaciónInstalación Y Operación Capacidad requerida de la bateríaInstrucciones DE Instalación DE LA BBU InstalaciónConfiguración de Fácil instalación Easy Install Layout Cableado Y Configuración DE LA BBU Figura 3 Marcar las uniones para encolarConexiones de la batería invertidas Posibles recursosTensión de la batería incorrecta Monitor de tiempo de carga 1 yLocalización DE Fallas Requisitos DE LA BateríaMantenimiento DE LA Batería Cuadro I Cálculo de la capacidad de la bateríaEstado de operación del sistema DEL de control Iluminación continua indica operación normalCorriente CA Cuadro V Funciones de los botones de controlSystem Alert Alerta del sistema Botón de control Resultado cuando se oprime el botónPiezas de repuesto Clave Número Descripción de la pieza De la pieza