Simer Pumps A5000-04 Installation, Basic Tools Materials Needed, Required Battery Capacity

Page 3

Installation

3

BATTERY BACKUP SYSTEM (BBU) INSTALLATION AND OPERATION

NOTICE:

Install this system during a time when the primary pump will not be needed. Gather all supplies before starting. Read all warnings and installation steps before you start.

Be prepared for water to leak from the coupling or piping when disassembling or cutting the discharge pipe. Protect system components, tools and supplies from getting wet. Dry any work areas that get wet.

BASIC TOOLS AND

MATERIALS NEEDED

Channel locks or large pliers

Tape measure

Socket wrench or 5/16” Nut driver

Side cutters

Hacksaw (to cut PVC pipe) Medium size pliers Pencil

Teflon tape

PVC glue (solvent weld) PVC pipe cleaner Cloth towel

100-120 Ampere-Hour Marine Deep Cycle Battery (sold separately)

Required Battery Capacity:

Single Battery: 120 ampere-hour maximum.

Double Batteries: 100 ampere-hours per battery (200 ampere-hours total)

Personal injury and flood hazard. Do not turn the pump on until all the fittings are glued and the glue has dried. Loose fittings can explode off of pipes and cause personal injury and flooding.

RETAIN ORIGINAL RECEIPT FOR YOUR RECORDS.

LIMITED WARRANTY

SIMER warrants to the original consumer purchaser (“Purchaser” or “You”) of its products that they are free from defects in material and workman- ship for a period of twelve (12) months from the date of the original consumer purchase.

If, within twelve (12) months from the original consumer purchase, any such product shall prove to be defective, it shall be repaired or replaced at SIMER’s option, subject to the terms and conditions set forth below. The original purchase receipt and product warranty information label are required to determine warranty eligibility. Eligibility is based on purchase date of original product – not the date of replacement under warranty. The warranty is limited to repair or replacement of product only – Purchaser pays all removal, installation, labor, shipping, and incidental charges.

For parts or troubleshooting assistance, DO NOT return product to your retail store. Contact SIMER Customer Service at 1-800-468-7867 / 1-800-546-7867.

Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail outlet where it was purchased immediately after the discovery of any alleged defect. SIMER will subsequently take corrective action as promptly as reasonably possible. No requests for service will be accepted if received more than 30 days after the warranty expires.

SEWAGE PUMPS

DO NOT return a sewage pump (that has been installed) to your retail store. Contact SIMER Customer Service. Sewage pumps that have seen service and been removed carry a contamination hazard with them.

If your sewage pump has failed:

• Wear rubber gloves when handling the pump;

• For warranty purposes, return the pump’s cord tag and original receipt of purchase to the retail store;

• Dispose of the pump according to local disposal ordinances.

Exceptions to the Twelve (12) Month Limited Warranty

Product

Warranty Period

BW85P, CM10, CMK, M40, M40P

90 days

 

 

2300, 2310, 2330, 2520ULST, 2955, 2956, 2957, 2960, A5500

2 Years

 

 

4” Submersible Well Pumps, 2958, 2975PC, 2985, 3075SS, 3983, 3984

3 Years

 

 

Pre-Charge Water System Tank, 3985, 3986

5 Years

 

 

3963, 3988, 3995, 3997

Lifetime

 

 

General Terms and Conditions

You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does not apply to the following:

(1)acts of God; (2) products which, in SIMER’s sole judgement, have been subject to negligence, abuse, accident, misapplication, tampering, or alteration; (3) failures due to improper installation, operation, maintenance or storage; (4) atypical or unapproved application, use or service;

(5)failures caused by corrosion, rust or other foreign materials in the system, or operation at pressures in excess of recommended maximums. This warranty sets forth SIMER’s sole obligation and purchaser’s exclusive remedy for defective products.

SIMER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You may also have other rights which vary from state to state.

SIMER • 293 Wright Street • Delavan, WI U.S.A. 53115

Phone: 1-800-468-7867 / 1-800-546-7867 • Fax: 1-800-390-5351

E-Mail: info@simerpumps.com • Web Site: http://www.simerpumps.com

Image 3
Contents 800 A5000-04Call Llame alGeneral Information SafetyRead and Follow Safety Instructions This is the safety alert symbol. When you see thisInstallation Required Battery CapacityBasic Tools Materials Needed Installation BBU Installation InstructionsEasy Install Layout Mark joints for gluing BBU Wiring and SetupCharge Time Monitor 1 Wrong Battery VoltageReversed Battery Connections Thermal Runaway ConditionTable I Battery Capacity Calculation Battery RequirementsBattery Maintenance TroubleshootingTable III LED Function Displays LEDs Lighted Continuously AC powerControl Button Result of Pushing Button Table IV Error Code Displays LEDs FlashingPump status Charging AC power Battery status Table V Control Button FunctionsPart Description Part Number Repair PartsRenseignements Généraux Voici le symbole indiquant quil faut être prudentSécurité Lire ET Observer LES Instructions DE SécuritéCapacité requise des batteries Outils ET Fournitures DE Base Dont on Aura BesoinÉtudier la pour les montages suggérés MontageInstallation Repérer les raccords pour les coller Câblage ET Montage DU Système DE Secours À BatterieClaquage thermique DEL affichées et touches de commande Tableau II, III, IV etRemèdes possibles Branchements de la batterie inversésTableau 1 Calcul de la capacité de la batterie Critères DE LA BatterieEntretien DE LA Batterie Recherche DES PannesTableau III DEL des fonctions les DEL restent allumées DEL des codes de fonctionnementTouches de contrôle Résultat Charging Charge AC power Battery status État de la batterieTableau IV Codes d’erreurs Les DEL clignotent Tableau V Fonctions des touches de contrôleRéf Désignation des pièces Numéro des pièces Pièces de rechangeEste es el símbolo de alerta de seguridad. Cuando Seguridad¡LEA Y Siga LAS Instrucciones DE Seguridad Información GeneralCapacidad requerida de la batería InstalaciónInstalación Y Operación Herramientas Y Materiales Básicos RequeridosInstalación Instrucciones DE Instalación DE LA BBUConfiguración de Fácil instalación Easy Install Layout Figura 3 Marcar las uniones para encolar Cableado Y Configuración DE LA BBUMonitor de tiempo de carga 1 y Posibles recursosTensión de la batería incorrecta Conexiones de la batería invertidasCuadro I Cálculo de la capacidad de la batería Requisitos DE LA BateríaMantenimiento DE LA Batería Localización DE FallasDEL de control Iluminación continua indica operación normal Estado de operación del sistemaBotón de control Resultado cuando se oprime el botón Cuadro V Funciones de los botones de controlSystem Alert Alerta del sistema Corriente CAClave Número Descripción de la pieza De la pieza Piezas de repuesto