Hitachi C 10RB instruction manual Removing the Blade FIG. E, Installing a Blade FIG. E, Stop

Page 13

REMOVING THE BLADE (FIG. E)

WARNING

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet.

1.Remove the table insert and raise the blade to the maximum height by turning the blade elevation handwheel clockwise.

2.Lift the blade guard and position it toward the rear of the table.

3.Adjust the blade to the 90° vertical position by unlocking the blade tilting lock knob and turning the bevel tilting handwheel counterclockwise, and then lock into position.

4.Pull the motor locking lever (1) toward the front of the machine while spinning the blade until the latch locks into place and the blade will no longer turn.

5.Place the blade wrench (3) on the arbor nut (4).

6.Loosen and remove the arbor nut and the flange by pulling the wrench toward the front of the machine.

7.Then remove the blade (6). Clean but do not remove the inner blade flange (5) before reassembling the blade.

Fig. E

1

 

 

3

4

 

6

 

5

INSTALLING A BLADE (FIG. E)

WARNING

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet.

1.Place the blade onto the arbor with the blade teeth pointing forward to the front of the saw.

2.Make sure the blade fits flush against the inner flange.

English

3.Clean the outer blade flange and install it onto the arbor and against the blade.

4.Thread the arbor nut onto the arbor, making sure the flat side of the nut is against the blade, then hand- tighten.

5.Pull the motor locking lever (1) toward the front of the machine while spinning the blade until the latch locks into place and the blade will no longer turn.

6.Place the wrench on the arbor nut and turn clockwise (toward the rear of the saw table).

7.Replace the table insert and blade guard assembly. Verify that the blade and blade guard splitter are aligned. If they are not, refer to page 12, Aligning The Blade Guard Splitter.

IMPORTANT: Do not operate this saw until the blade and blade guard splitter are aligned and in working order.

ADJUSTING THE 90° AND 45° POSITIVE STOPS (FIG. F, G)

Your saw has positive stops that will quickly position the saw blade at 90° and 45° to the table. Make adjustments only if necessary.

90° Stop

1.Disconnect the saw from the power source.

2.Raise the blade to the maximum elevation.

3.Loosen the blade bevel lock handle and move the blade to the maximum vertical position and tighten the bevel lock handle.

4.Place a combination square on the table and against the blade (1) to determine if the blade is 90° to the table. (Fig. F)

5.If the blade is not 90° to the table, loosen or tighten (depending on increasing or decreasing the degree) the hex screw (3) with a 5 mm hex wrench until you achieve 90°.(Fig. G)

6.The re-loosen the bevel lock handle and reset the blade at the maximum vertical position, then tighten the bevel lock handle.

7.Check again to see if the blade is 90° to the table. If not, repeat step 5.

8.Lastly, check the bevel angle scale. If the pointer does not read 90°, loosen the screw holding the pointer and move the pointer so it is accurate at 0° and retighten the pointer screw.

– 13 –

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Mode D’EMPLOI ET Instructions DE Securite Contents Motor SAW Product SpecificationsEnglish Power Tool SafetyTable SAW Safety Power Supply Requirements Electrical Requirements and SafetyExtension Cord Requirements Guidelines for Extension CordsTools Needed for Assembly Accessories and AttachmentsCarton Contents Unpacking Your Jobsite Table SAW Know Your Jobsite Table SAW Table SAW Terms Glossary of TermsWoodworking Terms Blade Guard Assembly FIG. C, D Assembly and AdjustmentsAssemble the Table SAW to the Stand Fig. a Assemble the Handwheel Handle FIG. BFig. D Aligning the Blade Guard Splitter FIG. DAdjusting the 90 and 45 Positive Stops FIG. F, G Installing a Blade FIG. ERemoving the Blade FIG. E StopBlade Parallel to the Miter Gauge Groove FIG. H Blade Tilt PointerInstalling the Table Insert FIG. L Additional Blade Adjustments FigStorage FIG. J, K Rip fence and miter gauge Fig. JRIP Fence Adjustment FIG. N RIP Fence Indicator FIG. O Miter Gauge Adjustment FIG. MIf adjustment is needed to make it parallel Miter Gauge Operation FIG. MFig. P Adjusting CAM Locking Lever FIG. QBasic SAW Operations OperationRipping FIG. V, W Cutting OperationsBevel Ripping Using Wood Facing on the Miter Gauge FigRipping Small Pieces Crosscutting FIGCompound Miter Crosscutting FIG. Z Using Wood Facing on the RIP Fence FIG. BBMiter Cuts FIG. AA Auxiliary Fence FIG. CCClamps. Fig. DD English Attach auxiliary fence to rip fence with two CDado Cuts FIG. EE General Maintenance MaintenanceMaintaining Your Table SAW LubricationSymptom Possible Causes Corrective Action Troubleshooting GuidePush Stick Construction Français Fiche Technique DU ProduitMoteur ScieAvertissement Consignes DE Sécurité SUR LES OutilsConsignes DE Sécurité SUR LA Scie À Table Exigences Concernant L’ Exigences Électriques ET SécuritéAlimentation Électrique Directives DE Mise À LA TerreOutils Requis Pour Assemblage AccessoiresContenu DE LA Boîte Déballage DE LA Scie À Table DE Chantier Apprendre À Connaître LA Scie À Table DE Chantier Termes Relatifs À LA Scie À Table Qualité PRO Craftsman GlossaireTermes DE Menuiserie Assemblage DE LA Scie À Table AU Support Fig. a Assemblage ET RéglagesAssemblage DE LA Poignée DU VOLANTFIG. B Assemblage DU PROTÈGE-LAME FIG. C, DAlignement DU Fendeur ET DU PROTÈGE-LAME Retrait DE LA Lame FIG. E Installation D’UNE Lame Fig. ERéglage DES Butées Fixes À 90 ET Pour éviter toute blessure causée par une mise enLame Parallèle À LA Rainure DE LA Jauge À Onglets FIG. H Indicateur D’INCLINAISON DE LameInstallation DE LA Plaque Amovible FIG. L Installation DU Rangement DU Poussoir FIG. JRangement FIG. J,K Utilisation DU Guide DE Coupe ’ONGLET FIG. M Reglage DU Guide DE Coupe DE FIL FIG. MRéglage DU Guide DE Refente FIG. N Si un réglage est requis pour le rendre parallèleRéglage DU Levier DE Blocage DE Came FIG. Q Indicateur D’ÉCHELLE DE Rallonge DE Table FIG. PFonctions DE Base DE LA Scie UtilisationUtilisation DE L’ÉJECTEUR DE Sciure FIG. T Inclinaison rapide de la lameSciage EN Long FIG. V, W Opérations DE CoupeCoupe EN Long DE Petites Pièces Coupe EN Long EN BiseauTronçonnagefig Tronçonnage EN Biseau FIG. YCoupes D’ONGLET FIG. AA Coupe Transversale D’ONGLET DE Type Mixte FIG. ZGuide Auxiliaire FIG.CC Rainurage FIG. EE De deux serres en « C » Fig. DDEntretien DE LA Scie À Table EntretienEntretien Général LubrificationProblème Causes Possibles Mesures Correctives Guide DE DépannageFabrication D’UN Poussoir Español Especificaciones DEL ProductoMotor Sierra Seguridad DE LA Herramienta Eléctrica Seguridad EN EL Manejo DE LA Sierra DE Mesa Requisitos DE LA Fuente Dealimentación Requisitos Electricos Y SeguridadRequisitos DE LOS Cablesprolongadores Indicaciones Para LOS CablesprolongadoresContenido DE LA Caja Accesorios Y AcoplesCómo Desempacar SU Sierra DE Mesa Para EL Lugar DE Trabajo La parte trasera de la sierra de mesa Conozca SU Sierra DE MesaTérminos DE LA Sierra DE Mesa Glosario DE TerminosTerminos DE Carpinteria Interruptor DE Reinicio POR SobrecargaMontaje DE LA Sierra DE Mesa Sobre EL Soporte Fig. a Montaje Y AjustesMontaje DEL Mango DEL Volante FIG. B Ensamblado DEL Protector DE LA Hoja FIG. C, DCómo Alinear EL Separador DEL Protector DE LA Hoja FIG. D Ajuste DE LOS Topes DE Seguridad a 90 Y Cómo Extraer LA Hoja FIG. ECartabon DE Ingletes FIG. H Alineacion DE LA Hoja CON LA Ranura DELIndicador DE Inclinación DE LA Hoja Almacenaje FIG. J, K Installing the PUSH-STICK Storage FIG. JCómo Instalar EL Inserto DE Mesa FIG. L Funcionamiento DE LA Guía DE Español Ajuste DE LA Guía DE Ingletes Fig. MIngletes Fig. M Ajuste DE LA Guía DE Corte FIG. NCómo Ajustar LA Palanca DE Bloqueo DE LA Leva FIG. Q Indicador DE LA Escala DE Extensión DE LA Mesa FIG. PFuncionamiento Elemental DE LA Sierra FuncionamientoInclinación DE LA Hoja Cómo Usar EL Conducto Para EL Aserrín FIG. TCorte EN Direccion a LA Veta FIG. V, W Operaciones DE CorteCorte AL Hilo DE Piezas Pequeñas Corte AL Hilo EN BiselCorte Transversal FIG USO DE Caras DE Madera EN LA Guía DE Ingletes FigUnion DE Inglete FIG. AA Corte Compuesto DE Ingletes FIG. ZFabricación del lateral Ensamblaje de las dos piezasCortes DE Ranura FIG. EE En forma de C. Fig. DDMantenimiento DE LA Sierra DE Mesa MantenimientoMantenimiento General Mecanismo DE LA Lamina ELEVATION/TILTING FIG. FFProblema Causas DEL Problema Solucion Guia Para LA Solucion DE ProblemasConstruccion DEL Empujador Parts List for Schematic Parts ListJOB Site Table SAW Model NO. C10RB Always order by I.D. NumberJOB Site Table SAW HKU# Parts List for StandPage Hitachi Koki Canada Co
Top Page Image Contents