Hitachi C 10FS instruction manual Before Using

Page 12

English

3. Installing the dust bag, holder, stopper and vises.

(The holder and stopper are optional accessories).

Attach the dust bag, holder, stopper and vise assembly, slide fence (A) and slide fence (B) as indicated in Fig. 1.

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same voltage as that specified on the nameplate of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned ON the power tool will start suddenly and can cause a serious accident.

3. Check the saw blade for visible defects.

Confirm that the saw blade is free of cracks or other visible damage.

4. Confirm that the saw blade is attached securely to the power tool.

Using the supplied 10mm box wrench, tighten the bolt on the saw blade spindle to secure the saw blade. For details, see Fig. 42-a and Fig. 42-b in the section on “SAW BLADE MOUNTING AND DISMOUNTING”.

5. Check the safety cover for proper operation.

Safety cover is designed to protect the operator from coming into contact with the saw blade during operation of the tool.

Always check that the safety cover moves smoothly and covers the saw blade properly.

Safety Cover

Fig. 7

WARNING: NEVER OPERATE THE POWER TOOL if the safety cover does not function smoothly.

6. Confirm the position of the spindle lock before using the tool.

After installing the saw blade, confirm that the spindle lock has been returned to the retract position before using the power tool (see Fig. 2).

7. Check the lower limit position of the Saw Blade.

Although it was adjusted before shipment, carefully check the height of the saw blade. Confirm that the saw blade can be lowered 13/32" to 27/64" (10mm to 11mm) below the table insert. For details, see the section on “Checking the saw blade lower limit position”.

8. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power cord plug fits properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace the receptacle if it is faulty.

9. Confirm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

10. Trial Run

After confirming that no one is standing behind, the power tool start and confirm that no operating abnormalities exist before attempting a cutting operation.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Avertissement AdvertenciaContents Meanings of Signal Words Inportant Safety Instructions for Using ALL Power ToolsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications DimensionAccessories ApplicationsInstallation Preparation Before OperationReleasing the locking pin Before Using Before Cutting Inspect the rotating stability of the saw bladeCutting a groove on the guard Positioning the table insertInstalling the holders ... Optional accessory Checking the saw blade lower limit positionOblique angle Securing the workpieceUsing an ink line Practical ApplicationsSwitch operation Using the Vise Assembly Standard accessoryCutting Operation Cutting narrow workpieces Press cutting Cutting wide workpieces Slide cuttingBevel cutting procedures Miter cutting proceduresCompound cutting procedures Crown molding cutting proceduresFor miter cut setting For bevel cut settingEnglish Groove cutting procedures Cutting depth adjustment procedureHow to use the dust bag Standard accessory SAW Blade Mounting and DismountingCutting easily-deformed materials, such as aluminum sash Mounting the saw blade -a and -bMaintenance and Inspection Adjusting a loose slide pipeOverload Protective Device for POLY-V-BELT Dismounting the saw bladeInspecting the safety cover for proper operation Replacement of Guard CInspecting the carbon brushes and Fig Inspecting the mounting screwsService and Repairs Replacement of Poly-V-BeltCleaning Handle for transportation and carryingInformations Importantes Signification DES Mots D’AVERTISSEMENTConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utiliser LE Cordon DE Rallonge AppropriéDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications Accessoires Plage de coupe mixtePréparation Avant L’UTILISATION Libérer la goupille de verrouillageAvant L’UTILISATION Installation de la plaque d’insertion Avant LA CoupeMarche d’essai 11. Vérifier la stabilité de rotation de la lameInstallation des supports ... Accessoires en option Vérification de la position de limite inférieure de la lameAngle oblique Fixation de la pièceApplications Pratiques Utilisation d’un trait d’encreUtilisation de l’ensemble d’étau Accessoire standard Fonctionnement de l’interrupteurEt la garde B Coupe Coupe de pièces minces Coupe à pression simpleCoupe de pièces larges Coupe avec chariot Procédure de coupe de biseau Procédure de coupe d’onglet Procédures de coupe mixteProcédures de coupe de corniche complexe Réglage d’une coupe d’onglet Réglage d’une coupe de biseauGarde Table du socle Procédures de coupe d’encoche Procédure de réglage de la profondeur de coupeInstallation ET Retrait DE LA Lame Utilisation du sac à copeaux Accessoire standardInstallation de la lame -a et -b Entretien ET Inspection Retrait de la lameInspection de la lame Réglage du tuyau de chariot s’il est relâchéRemplacement de la protection C Inspecter les balais carbone et FigInspection des vis de montage Vérifier si le garde de sécurité fonctionne correctementService APRÈS-VENTE ET Réparations Remplacement de la poly-courroie enPoignée pour le transport GraissageInformación Importante Significado DE LAS Palabras ClaveNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilice EL Cable Prolongador AdecuadoAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Accesorios AplicacionesPreparativos Previos a LA Operación InstalaciónLiberación del pasador de bloqueo Antes DE LA Utilización Cerciórese de que el interruptor de disparo esté en OFFCompruebe si la hoja de sierra posee defectos visibles Antes DEL Corte Compruebe el tomacorriente de CAOperación de prueba Inspeccione la estabilidad de rotación de la hoja de sierraUbicación del inserto de la mesa Ángulo oblicuoInmovilización de la pieza de trabajo Instalación de los soportes ... Accesorios opcionalesUtilización de una línea de tinta Aplicaciones Prácticas Operación de conmutaciónEl eje del tornillo de carpintero posee cuatro ranuras de Operación de corte Corte de piezas de trabajo estrechas Corte a presiónCorte de piezas de trabajo anchas Corte con deslizamiento Procedimientos de corte de ingletesProcedimiento de corte de ingletes Procedimientos de corte compuestoProcedimientos de corte con moldura en vértice Para el ajuste de corte de ingletesPara el ajuste del corte en bisel Ngu Procedimientos de corte de ranuras Procedimiento de ajuste de la profundidad de corteMontaje Y Desmontaje DE LA Hoja DE Sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a y -b Desmontaje de la hoja de sierra Mantenimiento E Inspección Almacenamiento Reemplazo del protector CReemplazo de la correa en V de polivinilo Manejo para transporteServicio Y Reparaciones LubricaciónLimpieza Parts List 10FS 10FS Slide Compound Saw Parts List Standard Accessories Page Hitachi Koki Canada Co
Top Page Image Contents