Hitachi C 10FS instruction manual Switch operation, Using the Vise Assembly Standard accessory

Page 16

English

1. Switch operation

Lock-off Button

Handle

Hole

Trigger

Switch

Fig. 17

The trigger switch lock-off button is designed to prevent inadvert- ent operation of the power tool.To operate the power tool, it is nec- essary to first fully insert the lock-off button into the hole on the handle as shown in Fig. 17.

The trigger switch will not operate unless the lock-off button has been pushed in.

When the trigger switch is released, the power goes off and the lock-off button automatically returns to its initial position, locking the trigger switch.

WARNING: Always remove the lock-off button from the handle when the power tool is not in use. This will ensure that the power tool cannot be turned on accidentally or by someone (especially a child) who is not qualified to use the power tool. If the lock-off button is left in the handle, serious personal injury can result. Since the lock-off button fits rather tightly, it may be necessary to turn it to the left and right during mounting and removing.

2. Using the Vise Assembly (Standard accessory)

Knob

Screw Holder

 

Vise Shaft

 

 

 

 

 

 

 

 

 

 

Alignment

 

 

Groove

Vise

 

 

 

 

 

 

 

 

Groove

 

Plate

 

 

 

 

 

Fence

 

Work-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

piece

 

 

10mm Knob

 

 

 

Bolt

 

 

 

 

 

 

 

 

Fig. 18

The vise assembly can be mounted on either the left fence {Fence (B)} or the right fence {Fence (A)}, and can be raised or lowered according to the height of the workpiece.

To raise or lower the vise assembly, first loosen the 10mm knob bolt. As shown in Fig. 18, the vise shaft has four locking grooves into which the tip of the 10mm knob bolt is designed to fit in order to lock the screw holder in the desired position.

To ensure that the tip of the 10mm knob bolt is properly aligned with the desired locking groove on the vise shaft, simply align the upper surface of the fence to either of three grooves on the vise shaft surface or to the lower surface of the screw holder.

Therefore, the vise assembly can be attached in either of four positions to ensure proper height adjustment.

After adjusting the height, firmly tighten the 10mm knob bolt; then turn the upper knob, as necessary, to securely attach the workpiece in position.

CAUTION: Always confirm that the motor head (see Fig. 1) does not contact the vise assembly when it is lowered for cutting. If there is any danger that it may do so, loosen the 10mm knob bolt slightly and move the vise to a position where it will not contact the saw blade.

Also, always confirm that the vise assembly is mounted on the right side {Fence (A)} before using the saw for compound cutting operations (miter + bevel cutting).

3. Using the Slide Fence (A) and Slide Fence (B) (Standard accessory)

2-4/3" (70mm)

2-5/32" (55mm)

Fence (B)

Fence (A)

Slide Fence (B)

 

Slide fence (A) and slide fence (B) are meant to stabilize small workpieces as shown in Fig. 19.

Slide Fence (A)

Workpiece

Cut off side piece

Clearance between fence (A) and fence (B) and the workpiece is necessary. The edge of workpiece should not overlap with fence (A) and fence (B).

Fig. 19

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Avertissement AdvertenciaContents Inportant Safety Instructions for Using ALL Power Tools Meanings of Signal WordsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications DimensionAccessories ApplicationsPreparation Before Operation InstallationReleasing the locking pin Before Using Before Cutting Inspect the rotating stability of the saw bladeCutting a groove on the guard Positioning the table insertInstalling the holders ... Optional accessory Checking the saw blade lower limit positionOblique angle Securing the workpieceUsing an ink line Practical ApplicationsSwitch operation Using the Vise Assembly Standard accessoryCutting Operation Cutting narrow workpieces Press cutting Cutting wide workpieces Slide cuttingBevel cutting procedures Miter cutting proceduresCompound cutting procedures Crown molding cutting proceduresFor miter cut setting For bevel cut settingEnglish Groove cutting procedures Cutting depth adjustment procedureHow to use the dust bag Standard accessory SAW Blade Mounting and DismountingCutting easily-deformed materials, such as aluminum sash Mounting the saw blade -a and -bMaintenance and Inspection Adjusting a loose slide pipeOverload Protective Device for POLY-V-BELT Dismounting the saw bladeInspecting the safety cover for proper operation Replacement of Guard CInspecting the carbon brushes and Fig Inspecting the mounting screwsService and Repairs Replacement of Poly-V-BeltCleaning Handle for transportation and carryingSignification DES Mots D’AVERTISSEMENT Informations ImportantesConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Utiliser LE Cordon DE Rallonge Approprié Pieces DE RechangeDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications Accessoires Plage de coupe mixtePréparation Avant L’UTILISATION Libérer la goupille de verrouillageAvant L’UTILISATION Installation de la plaque d’insertion Avant LA CoupeMarche d’essai 11. Vérifier la stabilité de rotation de la lameInstallation des supports ... Accessoires en option Vérification de la position de limite inférieure de la lameAngle oblique Fixation de la pièceApplications Pratiques Utilisation d’un trait d’encreUtilisation de l’ensemble d’étau Accessoire standard Fonctionnement de l’interrupteurEt la garde B Coupe de pièces minces Coupe à pression simple CoupeCoupe de pièces larges Coupe avec chariot Procédure de coupe de biseau Procédures de coupe mixte Procédure de coupe d’ongletProcédures de coupe de corniche complexe Réglage d’une coupe d’onglet Réglage d’une coupe de biseauGarde Table du socle Procédures de coupe d’encoche Procédure de réglage de la profondeur de coupeUtilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameInstallation de la lame -a et -b Entretien ET Inspection Retrait de la lameInspection de la lame Réglage du tuyau de chariot s’il est relâchéRemplacement de la protection C Inspecter les balais carbone et FigInspection des vis de montage Vérifier si le garde de sécurité fonctionne correctementService APRÈS-VENTE ET Réparations Remplacement de la poly-courroie enPoignée pour le transport GraissageSignificado DE LAS Palabras Clave Información ImportanteNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Utilice EL Cable Prolongador Adecuado Piezas DE ReemplazoAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Accesorios AplicacionesInstalación Preparativos Previos a LA OperaciónLiberación del pasador de bloqueo Cerciórese de que el interruptor de disparo esté en OFF Antes DE LA UtilizaciónCompruebe si la hoja de sierra posee defectos visibles Antes DEL Corte Compruebe el tomacorriente de CAOperación de prueba Inspeccione la estabilidad de rotación de la hoja de sierraUbicación del inserto de la mesa Ángulo oblicuoInstalación de los soportes ... Accesorios opcionales Inmovilización de la pieza de trabajoUtilización de una línea de tinta Aplicaciones Prácticas Operación de conmutaciónEl eje del tornillo de carpintero posee cuatro ranuras de Operación de corte Corte de piezas de trabajo estrechas Corte a presiónCorte de piezas de trabajo anchas Corte con deslizamiento Procedimientos de corte de ingletesProcedimiento de corte de ingletes Procedimientos de corte compuestoPara el ajuste de corte de ingletes Procedimientos de corte con moldura en vérticePara el ajuste del corte en bisel Ngu Procedimientos de corte de ranuras Procedimiento de ajuste de la profundidad de corteForma de utilizar la bolsa para el polvo Accesorio estándar Montaje Y Desmontaje DE LA Hoja DE SierraMontaje de la hoja de sierra -a y -b Desmontaje de la hoja de sierra Mantenimiento E Inspección Almacenamiento Reemplazo del protector CReemplazo de la correa en V de polivinilo Manejo para transporteLubricación Servicio Y ReparacionesLimpieza Parts List 10FS 10FS Slide Compound Saw Parts List Standard Accessories Page Hitachi Koki Canada Co
Top Page Image Contents