Hitachi C 10FS instruction manual Specific Safety Rules for Use of this Power Tool

Page 4

English

10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE. Use clamps or a vise to hold the workpiece in place. It is safer than using your hand and it frees both hands to operate the tool.

11.NEVER OVERREACH. Always keep proper footing and balance when working with the tool.

12.ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and clean for the best and safest performance. Always follow instructions for lubricating the tool and for changing accessories.

13.ALWAYS DISCONNECT THE TOOL before servicing and before changing blades or other accessories.

14.NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. Always confirm that the switch is in the OFF position before inserting the power plug into the receptacle.

15.ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN OPERATING THIS TOOL.

Consult this instruction manual for descriptions of recommended accessories.To avoid personal injuries, use only recommended accessories in conjunction with this tool.

16.NEVER STAND ON THE TOOL. Prevent serious injury by not tipping the tool and by not risking unintentional contact with the saw blade.

17.ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL. Always check the guard and all other components for damage before using the tool to assure that they will function properly. Check all moving parts for proper alignment, freedom from binding and other conditions that might affect proper operation. Always repair or replace any damaged guards or other damaged components before using the tool.

18.ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE BEFORE USING THE TOOL. Always feed work into the tool against the rotation direction of the blade in order to prevent possible injury.

19.NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop. Always turn the power off when the tool is not in use. Always unplug the power cord when the tool is not in use.

20.This tool was not designed to be used for mass-production applications and should not be used in mass-production environments.

21.When servicing this tool, use only authorized replacement parts.

22.Apply 115 volts AC only to this tool. Applying the wrong voltage or applying DC power can cause the POWER TOOL to operate improperly and cause serious personal injury or damage to the tool.

23.Never raise the saw blade from the workpiece until it has first come to a complete stop.

24.Always use outboard stands to provide support for long workpieces that overhang the table of the slide compound saw.

25.Always return the carriage to the full rear position after each crosscut operation in order to reduce the risk of injury.

26.POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other).This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Specific Safety Rules for Use of this Power Tool

WARNING: The following specific operating instructions must be observed when using this POWER TOOL in order to avoid injury:

DO’s

ALWAYS OBSERVE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1.Review this Manual and familiarize yourself with the safety rules and operating instructions for this POWER TOOL before attempting to use it.

2.Always confirm that the POWER TOOL is clean before using it.

3.Always wear snug-fitting clothing, non-skid footwear (preferably with steel toes) and eye protection when operating the POWER TOOL.

4.Always handle the POWER TOOL carefully. If the POWER TOOL falls or strikes against a hard object, it might become deformed or cracked or sustain other damage.

5.Always cease operating the saw at once, if you notice any abnormality whatsoever.

4

Image 4
Contents Avertissement AdvertenciaContents Inportant Safety Instructions for Using ALL Power Tools Meanings of Signal WordsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications DimensionAccessories ApplicationsPreparation Before Operation InstallationReleasing the locking pin Before Using Before Cutting Inspect the rotating stability of the saw bladeCutting a groove on the guard Positioning the table insertInstalling the holders ... Optional accessory Checking the saw blade lower limit positionOblique angle Securing the workpieceUsing an ink line Practical ApplicationsSwitch operation Using the Vise Assembly Standard accessoryCutting Operation Cutting narrow workpieces Press cutting Cutting wide workpieces Slide cuttingBevel cutting procedures Miter cutting proceduresCompound cutting procedures Crown molding cutting proceduresFor miter cut setting For bevel cut settingEnglish Groove cutting procedures Cutting depth adjustment procedureHow to use the dust bag Standard accessory SAW Blade Mounting and DismountingCutting easily-deformed materials, such as aluminum sash Mounting the saw blade -a and -bMaintenance and Inspection Adjusting a loose slide pipeOverload Protective Device for POLY-V-BELT Dismounting the saw bladeInspecting the safety cover for proper operation Replacement of Guard CInspecting the carbon brushes and Fig Inspecting the mounting screwsService and Repairs Replacement of Poly-V-BeltCleaning Handle for transportation and carryingSignification DES Mots D’AVERTISSEMENT Informations ImportantesConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Utiliser LE Cordon DE Rallonge Approprié Pieces DE RechangeDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications Accessoires Plage de coupe mixtePréparation Avant L’UTILISATION Libérer la goupille de verrouillageAvant L’UTILISATION Installation de la plaque d’insertion Avant LA CoupeMarche d’essai 11. Vérifier la stabilité de rotation de la lameInstallation des supports ... Accessoires en option Vérification de la position de limite inférieure de la lameAngle oblique Fixation de la pièceApplications Pratiques Utilisation d’un trait d’encreUtilisation de l’ensemble d’étau Accessoire standard Fonctionnement de l’interrupteurEt la garde B Coupe de pièces minces Coupe à pression simple CoupeCoupe de pièces larges Coupe avec chariot Procédure de coupe de biseau Procédures de coupe mixte Procédure de coupe d’ongletProcédures de coupe de corniche complexe Réglage d’une coupe d’onglet Réglage d’une coupe de biseauGarde Table du socle Procédures de coupe d’encoche Procédure de réglage de la profondeur de coupeUtilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameInstallation de la lame -a et -b Entretien ET Inspection Retrait de la lameInspection de la lame Réglage du tuyau de chariot s’il est relâchéRemplacement de la protection C Inspecter les balais carbone et FigInspection des vis de montage Vérifier si le garde de sécurité fonctionne correctementService APRÈS-VENTE ET Réparations Remplacement de la poly-courroie enPoignée pour le transport GraissageSignificado DE LAS Palabras Clave Información ImportanteNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Utilice EL Cable Prolongador Adecuado Piezas DE ReemplazoAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Accesorios AplicacionesInstalación Preparativos Previos a LA OperaciónLiberación del pasador de bloqueo Cerciórese de que el interruptor de disparo esté en OFF Antes DE LA UtilizaciónCompruebe si la hoja de sierra posee defectos visibles Antes DEL Corte Compruebe el tomacorriente de CAOperación de prueba Inspeccione la estabilidad de rotación de la hoja de sierraUbicación del inserto de la mesa Ángulo oblicuoInstalación de los soportes ... Accesorios opcionales Inmovilización de la pieza de trabajoUtilización de una línea de tinta Aplicaciones Prácticas Operación de conmutaciónEl eje del tornillo de carpintero posee cuatro ranuras de Operación de corte Corte de piezas de trabajo estrechas Corte a presiónCorte de piezas de trabajo anchas Corte con deslizamiento Procedimientos de corte de ingletesProcedimiento de corte de ingletes Procedimientos de corte compuestoPara el ajuste de corte de ingletes Procedimientos de corte con moldura en vérticePara el ajuste del corte en bisel Ngu Procedimientos de corte de ranuras Procedimiento de ajuste de la profundidad de corteForma de utilizar la bolsa para el polvo Accesorio estándar Montaje Y Desmontaje DE LA Hoja DE SierraMontaje de la hoja de sierra -a y -b Desmontaje de la hoja de sierra Mantenimiento E Inspección Almacenamiento Reemplazo del protector CReemplazo de la correa en V de polivinilo Manejo para transporteLubricación Servicio Y ReparacionesLimpieza Parts List 10FS 10FS Slide Compound Saw Parts List Standard Accessories Page Hitachi Koki Canada Co