Hitachi C 10FS Overload Protective Device for POLY-V-BELT, Maintenance and Inspection

Page 24

English

(3) Lift the safety cover and mount the saw blade.

WARNING: When mounting the saw blade, confirm that the rotation indicator mark on the saw blade and the rotation direction of the side cover (L) (see Fig. 1) are properly matched.

(4)Thoroughly clean washer (C) and the bolt, and install them onto the saw blade spindle.

(5)Press in the spindle lock and tighten the bolt by turning it to the left by 10mm box wrench as indicated in Fig. 42-b.

CAUTION: * A dust guide is installed inside behind the side cover (L).

When removing or installing the saw blade, do not make contact with the dust guide. Contact may break or chip saw blade tips.

*Confirm that the spindle lock has returned to the retract position after installing or removing the saw blade.

*Tighten the bolt so it does not come loose during operation.

Confirm the bolt has been properly tightened before the power tool is started.

2.Dismounting the saw blade

Dismount the saw blade by reversing the mounting procedures described in paragraph 1 above. The saw blade can easily be removed after lifting the safety cover.

CAUTION: Never attempt to install saw blades larger than 10" (255mm) in diameter. Always install saw blades that are 10" (255mm) in diameter or less.

OVERLOAD PROTECTIVE DEVICE FOR POLY-V-BELT

The power of the motor is transmitted to the saw blade by a Poly-V-Belt. When the Poly-V-Belt becomes overloaded, the overload protective device cuts off the current to stop the motor.

In this case turn the switch off immediately and raise the handle to its initial position. Then turn the switch on and after running the tool for 20 seconds without a load for cooling of the motor. Then start the cutting operation.The Poly-V-Belt or the motor will be damaged if the overload protective device turns off frequently.

CAUTION: When the overload protective device stops the motor, the motor will start by turning the switch on after turning it off. When turning the switch on, make sure that the saw blade is not halfway in the material.

MAINTENANCE AND INSPECTION

WARNING: To avoid an accident or personal injury, always confirm that the trigger switch is turned OFF and the power plug has been disconnected from the receptacle before performing any maintenance or inspection of this tool.

1. Inspecting the saw blade

Always replace the saw blade immediately upon the first sign of deterioration or damage.

A damaged saw blade can cause personal injury and a worn saw blade can cause ineffective operation and possible overload to the motor.

CAUTION: Never use a dull saw blade. When a saw blade is dull, its resistance to the hand pressure applied by the tool handle tends to increase, making it unsafe to operate the power tool.

2. Adjusting a loose slide pipe

8mm Hex. Socket

8mm Nut

Bushing

Head Screw

Slide Pipe (A)

Holder (A)

After extended use of the power tool, the slide pipe (A) and the bushing can become loose due to vibration. Never operate the tool if any components are loose to avoid personal injury.

(1)Loosen the 8mm nut and tighten the four 8mm hexagon socket set screws until the power tool operates smoothly without looseness.

(2)Properly tighten the 8mm nut after completing these adjustment.

Fig. 43

24

Image 24
Contents Avertissement AdvertenciaContents Meanings of Signal Words Inportant Safety Instructions for Using ALL Power ToolsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications DimensionAccessories ApplicationsInstallation Preparation Before OperationReleasing the locking pin Before Using Before Cutting Inspect the rotating stability of the saw bladeCutting a groove on the guard Positioning the table insertInstalling the holders ... Optional accessory Checking the saw blade lower limit positionOblique angle Securing the workpieceUsing an ink line Practical ApplicationsSwitch operation Using the Vise Assembly Standard accessoryCutting Operation Cutting narrow workpieces Press cutting Cutting wide workpieces Slide cuttingBevel cutting procedures Miter cutting proceduresCompound cutting procedures Crown molding cutting proceduresFor miter cut setting For bevel cut settingEnglish Groove cutting procedures Cutting depth adjustment procedureHow to use the dust bag Standard accessory SAW Blade Mounting and DismountingCutting easily-deformed materials, such as aluminum sash Mounting the saw blade -a and -bMaintenance and Inspection Adjusting a loose slide pipeOverload Protective Device for POLY-V-BELT Dismounting the saw bladeInspecting the safety cover for proper operation Replacement of Guard CInspecting the carbon brushes and Fig Inspecting the mounting screwsService and Repairs Replacement of Poly-V-BeltCleaning Handle for transportation and carryingInformations Importantes Signification DES Mots D’AVERTISSEMENTConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utiliser LE Cordon DE Rallonge AppropriéDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications Accessoires Plage de coupe mixtePréparation Avant L’UTILISATION Libérer la goupille de verrouillageAvant L’UTILISATION Installation de la plaque d’insertion Avant LA CoupeMarche d’essai 11. Vérifier la stabilité de rotation de la lameInstallation des supports ... Accessoires en option Vérification de la position de limite inférieure de la lameAngle oblique Fixation de la pièceApplications Pratiques Utilisation d’un trait d’encreUtilisation de l’ensemble d’étau Accessoire standard Fonctionnement de l’interrupteurEt la garde B Coupe Coupe de pièces minces Coupe à pression simpleCoupe de pièces larges Coupe avec chariot Procédure de coupe de biseau Procédure de coupe d’onglet Procédures de coupe mixteProcédures de coupe de corniche complexe Réglage d’une coupe d’onglet Réglage d’une coupe de biseauGarde Table du socle Procédures de coupe d’encoche Procédure de réglage de la profondeur de coupeInstallation ET Retrait DE LA Lame Utilisation du sac à copeaux Accessoire standardInstallation de la lame -a et -b Entretien ET Inspection Retrait de la lameInspection de la lame Réglage du tuyau de chariot s’il est relâchéRemplacement de la protection C Inspecter les balais carbone et FigInspection des vis de montage Vérifier si le garde de sécurité fonctionne correctementService APRÈS-VENTE ET Réparations Remplacement de la poly-courroie enPoignée pour le transport GraissageInformación Importante Significado DE LAS Palabras ClaveNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilice EL Cable Prolongador AdecuadoAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Accesorios AplicacionesPreparativos Previos a LA Operación InstalaciónLiberación del pasador de bloqueo Antes DE LA Utilización Cerciórese de que el interruptor de disparo esté en OFFCompruebe si la hoja de sierra posee defectos visibles Antes DEL Corte Compruebe el tomacorriente de CAOperación de prueba Inspeccione la estabilidad de rotación de la hoja de sierraUbicación del inserto de la mesa Ángulo oblicuoInmovilización de la pieza de trabajo Instalación de los soportes ... Accesorios opcionalesUtilización de una línea de tinta Aplicaciones Prácticas Operación de conmutaciónEl eje del tornillo de carpintero posee cuatro ranuras de Operación de corte Corte de piezas de trabajo estrechas Corte a presiónCorte de piezas de trabajo anchas Corte con deslizamiento Procedimientos de corte de ingletesProcedimiento de corte de ingletes Procedimientos de corte compuestoProcedimientos de corte con moldura en vértice Para el ajuste de corte de ingletesPara el ajuste del corte en bisel Ngu Procedimientos de corte de ranuras Procedimiento de ajuste de la profundidad de corteMontaje Y Desmontaje DE LA Hoja DE Sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a y -b Desmontaje de la hoja de sierra Mantenimiento E Inspección Almacenamiento Reemplazo del protector CReemplazo de la correa en V de polivinilo Manejo para transporteServicio Y Reparaciones LubricaciónLimpieza Parts List 10FS 10FS Slide Compound Saw Parts List Standard Accessories Page Hitachi Koki Canada Co