DeWalt DeVILBISS To Drain Tank, Oil, Checking, Changing, Air Filter Inspection and Replacement

Page 19

To Drain Tank

1.Set the On/Auto/Off lever to "Off".

2.Pull the regulator knob out and turn counter clockwise to set the outlet pressure to zero.

3.Remove the air tool or accessory.

4.Pull ring on safety valve allowing air to bleed from the tank until tank pressure is approximately 20 psi. Release safety valve ring.

5.Drain water from air tank by opening drain valve (counter- clockwise) on bottom of tank.

Water will condense in the air

tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture.

6.After the water has been drained, close the drain valve (clockwise). The air compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled.

Oil

Drain tank to release air pressure

before removing the oil fill cap or oil drain plug.

Checking

1.Remove the oil fill plug (A). The

oil level should
oil level should		A
be even with the		A
be even with the
top of the fill
hole and no
lower than 6
threads from the
threads from the			B
top of fill hole.

2.If needed, slowly add oil until it reaches the top of fill hole.

NOTE: Oil is included with some units. If oil is not included, use an oil specifically formulated for use in an air compressor, such as Porter-Cable PAS1 air compressor oil. Oil may be found at the store where the air compressor was purchased.

Changing

1.Remove the oil fill plug (A).

2.Remove the oil drain plug (B) and drain oil into a suitable container.

3.Replace the oil drain plug (B) and tighten securely

4.Slowly fill crankcase to the top of the fill hole. NOTE: Crankcase oil capacity is approximately 16 fluid ounces (473.2 ml).

Over filling with oil will cause

premature compressor failure. Do not overfill.

5.Replace oil fill plug (A) and tighten securely.

Air Filter - Inspection and Replacement

Hot surfaces. Risk of burn.

Compressor heads are exposed when filter cover is removed. Allow compressor to cool prior to servicing.

Keep the air filter clean at all times.

Do not operate the air compressor with the air filter removed.

A dirty air filter will not allow the compressor pump to operate at full capacity. Before using the compressor pump, check the air filter to make sure it is clean and in place.

If it is dirty, replace it with a new filter.

19- ENG

D23766

Image 19

Contents OPERATOR’S Manual Maintenance InstructionsSafety Guidelines Definitions Table of ContentsImportant Safety Instructions Hazard What Could Happen Attachments & AccessoriesHazard Guards or covers which are damaged or Fire, Inhalation, Damage to Vehicle Surfaces Duty Cycle AccessoriesON-RECEIPT Inspection GlossaryUnpacking AssemblyTools Required for Assembly To Install HandleTo Add Oil To Pump To Assemble WheelsAssemble Rubber Strip if equipped Assemble Rubber Feet if equippedPlace unit on a level surface Plug Grounded Outlets Grounding Pin InstallationLocation of the Air Compressor Extension Cords120/240 Dual Voltage Motor Voltage and Circuit ProtectionAir Distribution System Typical Compressed AIR Distribution System Know Your Air Compressor OperationDescription of Operation Before Starting How to StopPressure Release Valve Check Valve Before Each Start-Up How to StartTo Check Safety Valve MaintenanceCustomer Responsibilities Checking Air Filter Inspection and ReplacementTo Drain Tank OilAir Compressor Pump Intake and Exhaust Valves Motor Pulley/Flywheel AlignmentScrewdriver Open position nothing is visible Service and AdjustmentsTo Replace or Clean Check Valve Outlet Tube Pressure Relief Tube Nuts Nuts Check ValveMotor Pressure Switch ReplacementTo Replace Regulator Regulator Arrow To Replace BeltWing Nut Storage Troubleshooting Pressure reading Problem Cause Correction Problem Cause Correction ENG D23766 Responsibility of Original Purchaser initial User WarrantyArmado, funcionamiento, e instrucciones de Manual DEL OperadorDefiniciones DE Normas DE Seguridad Tabla DE ContenidosLesiones serias Causar daños en la propiedad Cómo prevenirlo Instrucciones Importantes DE SeguridadQué puede occurrir Cómo prevenirlo Advertencia Riesgo de Explosión35- SP D23766 Advertencia Riesgo de Caída Qué puede occurrir Advertencia Riesgo de Quemaduras Qué puede occurrirAdvertencia Riesgo de Operación Lasegura Qué puede occurrir Accesorios Inspección AL RecibirGlosario Ciclo DE ServicioInstalación del asa EnsambladoHerramientas necesarias para el ensamble DesempaquePara agregar aceite a la bomba Ensamble de las ruedasEnsamble de las patas de goma Si viene equipado Aplicación de la tira de goma Si viene equipadoDrene el tanque a fin de liberar Enchufe InstalaciónUbicación del compresor de aire Cables de extensión eléctricaLos tubos de plástico o PVC No han sido diseñados Protección del voltaje y del circuitoSistema de distribución de aire Cuando se convierte paraSistema Típico DE Distribución DE Aire Conozca su compresor de aire FuncionamientoDescripción de funcionamiento Procedimiento para el asentamiento Cómo utilizar su unidadAntes de poner en marcha Cómo detenerlaCómo poner en marcha Antes de cada puesta en marchaResponsabilidades del cliente MantenimientoCómo verificar la válvula de seguridad Cambio Cómo drenar el tanqueAceite VerificaciónPolea y volante del motor Alineación Tuercas TuercasVálvula reguladora Servicio Y AjustesPara reemplazar o limpiar la válvula De retención Tubo de salidaInterruptor de Presión Reemplazo MotorPara reemplazar el regulador Regulador Flecha Cambio de la correaTuerca mariposa Almacenaje Guía DE Diagnóstico DE Problemas Condiciones de flujo mientras se esté Retire y limpie, o reemplace D23766 58- SP Notas Responsabilidad DEL Comprador Original Usuario inicial Garantía LimitadaGuide DE Lutilisateur Mesures DE Sécurité Définitions Table DES MatièresConsignes DE Sécurité Importantes Avertissement Risque dexplosion ou dincendie Prévention Conserver ces directivesRisque Prévention Avertissement Risque déclatementAvertissement Risque de projection dobjets Avertissement Risque par inhalation Avertissement Risque de choc électriqueAvertissement Risque relié aux pièces mobiles Avertissement Risque de brûluresAvertissement Risque de chute Avertissement Risque dune utilisation dangereuse RisqueLexique Cycle DE ServiceAccessoires Vérification SUR RéceptionDéballage Installation de la poignéeAssemblage Outils requis pour lassemblageAjout dhuile à la pompe Assemblage des rouesAssemblage des pieds en caoutchouc si fournis Application de la bande en caoutchouc si fourniePurgez le réservoir pour Broche de mise à la terre Emplacement du compresseur dairRallonges FicheTension et protection des circuits Moteur deux tensions de 120/240 voltsSystème de distribution dair Système DE Distribution Dair Typique Familiarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Pompe du compresseur dair non illustrée Utilisation de lappareil Arrêt de lappareilAvant le démarrage Système de refroidissement non illustréMise en marche Avant chaque mise en marcheResponsabilités du consommateur EntretienVérification de la soupape de sûreté Vérification Filtre à air Inspection et remplacementVidange du réservoir HuileAlignement de la poulie et du volant- moteur Réparations ET Réglages Remplacement ou nettoyage de la soupape de retenueRemplacement du régulateur Manostat RemplacementMoteur Régulateur Flèche Remplacement de la courroieÉcrou à oreilles Placez le levier « On/Auto/Off » à la position « Off » RangementRisquerait de rompre ou DépannageDe modifier le réservoir dair De quelque façon. Celui-ciSi la soupape fuit toujours Le moteur ne Bruit de cliquetis 89- FR D23766 90- FR 91- FR D23766 Responsabilité DE Lacheteur Dorigine utilisateur initial Garantie Limitée