Delta 20-400 instruction manual Install Blade Tensioning Knob, Install Band SAW Blade

Page 10

ASSEMBLY

INSTALL BLADE TENSIONING KNOB

•Fit the blade tensioning knob (A) onto the blade tensioning spindle (B) located at the top of the

machine.

Figure 5

INSTALL BAND SAW BLADE

•Open the upper and lower cabinets of the saw by turning the cabinet lock knobs (A) clockwiseSee Figure 6.

•Locate the blade tensioning knob (B) at the top of the machine and turn it counterclockwise several rotations to lower the upper flywheel.

•Carefully feed the blade through the slot in the table (A), ensuring that the blade teeth are pointing down

toward the table. See Figure 7.

•Once the blade is in the throat of the saw table, rotate

it clockwise 90°, toward you. The blade teeth should now be facing you.

•Carefully slide the blade through the upper slot (B)

and lower slot (C) located to the right of the wheel guard.

	• Loop the upper part of the blade over the upper tire
	and the lower part of the blade over the lower tire.
	See Figure 8. If you need to create additional slack,
	rotate the blade tensioning knob (D) counterclockwise	Figure 7
	until the blade can be slipped over both flywheels	Figure 7
	until the blade can be slipped over both flywheels

•Tighten the blade tensioning knob until there is sufficient tension on blade. (See “Adjusting the Blade

Tension", page 13).

Figure 6

NOTE: Once your DELTA® Band Saw is set up, you may want to cut several scraps of various species and thicknesses of wood. Check for bowing in the cut and add more tension to the blade if necessary. Different blade sizes will also require different tension settings.

10

Image 10

Contents 14 in. Steel Frame Band Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions General Safety RulesAdditional Specific Safety Rules Refer to them often and use them to instruct othersGrounding Instructions POWER CONNECTIONSMotor Specifications All grounded, cord-connected machinesEXTENSION CORDS Minimum Gauge Extension CordKEY Features and Components Functional DescriptionProduct Specifications UnpackingSecure Table to Table Trunnion System AssemblyStand Assembly Attaching the SAW to the StandInstall Blade Tensioning Knob Install Band SAW BladeInsert Throat Plate Adjust the Blade TrackingSee Figure Disconnect the machine from the power source Square Table to BladeStarting and Stopping the SAW Using the Safety KEY to Lock the Switch in the OFF PositionOperation Selecting Proper Cutting SpeedTilting the Table Disconnect the machine from the power source See FigureOperation Positioning the Upper Blade GuideAdjusting the Blade Tension AdjustmentsCutting Curves Adjusting the Blade Guides and Bearings Adjusting Blade TrackingKeep Machine Clean MaintenanceTroubleshooting Failure to StartTrouble Band SAW does not Come UP to Speed Probable CauseAbout Band SAW Blades AccessoriesWarranty TipsReplacement Parts Service and RepairsConsignes DE Sécurité Importantes Consignes DE Sécurité DéfinitionsRègles DE Sécurité Générales Suite à laRègles DE Sécurité Spécifiques Supplémentaires Conservez CES ConsignesSpécifications DU Moteur Raccordements ÉlectriquesInstructions DE Mise À LA Terre Rallonges Fonctionnement monophasé 240 VoltsCaractéristiques ET Composantes Description du FONCTIONNEmentCaractéristiques DU Produit DéballageFixer LA Table AU Système DE Tourillons DE Table MontageMontage DU Support Fixer LA Scie AU SupportInstaller LA Lame DE LA Scie À Ruban Installer LA Poignée DE Tension DE LA LameVoir Figure Insérer LA Plaque Lumière Régler LE Suivi DE LA LameAligner LA Table ET LA Lame Démarrage ET Arrêt DE LA Scie FonctionnementSélection DE LA Bonne Vitesse DE Coupe Incliner LA Table Positionner LE Guide DE Lame SupérieurCouper DES Courbes AjustementsRégler LA Tension DE LA Lame Régler LES Guides DE Lame ET Paliers Régler LE Suivi DE LameDépannage Cause probable SolutionEntretien Échec DU DémarrageCause probable Solution Curseur déréglé Réglez le curseur Cause probableGarantie AccessoiresPropos DES Lames DE Scie À Ruban ConseilsAide Pour LES PIÈCES, LE Service OU LA Garantie Service ET RéparationsInstrucciones Importantes DE Seguridad Normas DE Seguridad DefinicionesReglas Generales DE Seguridad Continúa en la páginaReglas Adicionales DE Seguridad Guarde Estas InstruccionesEspecificaciones DEL Motor Conexiones DE AlimentaciónInstrucciones DE Conexión a Tierra Alargadores Eléctricos Alargador Eléctrico DE Calibre MínimoCaracterísticas Y Componentes Clave Descripción FuncionalEspecificaciones DEL Producto DesembalajeSujete LA Mesa AL Sistema DE Muñones DE Mesa EnsamblajeEnsamblaje DE LA Base Consulte la FiguraInstale LA Hoja DE LA Sierra Cinta Instale LA Perilla Tensionadora DE LA HojaVea la figura Inserte LA Placa DE Garganta Ajuste DEL Desplazamiento DE LA HojaCuadre LA Mesa a LA Hoja Encender Y Detener LA Sierra FuncionamientoSelección DE LA Velocidad DE Corte Adecuada Inclinación DE LA Mesa Posicionamiento DE LA Guía DE LA Hoja SuperiorCorte DE Curvas AjustesAjuste DE LA Tensión DE LA Hoja Ajuste DE LAS Guías Y LOS Rodamientos DE LA Hoja De la fuente de alimentaciónFalla EN EL Encendido ReSOLUCIÓN DE ProblemasMantenimiento Mantenga LA Máquina LimpiaProblema LA Sierra Cinta no Alcanza LA Velocidad Deseada Causa probableGarantía Acerca DE LAS Hojas Para Sierra CintaAccesorios SugerenciasAsistencia Sobre GARANTÍA, Servicio O Piezas Servicio Técnico Y ReparacionesAirport Road Anderson, SC 800