Delta 20-400 Adjust the Blade Tracking, Insert Throat Plate, Square Table to Blade

Page 11

ASSEMBLY

 

ADJUST THE BLADE TRACKING

 

See Figure 9.

 

Disconnect the machine from the

 

power source before making any

 

adjustments!

 

IMPORTANT: Before tracking the blade, confirm that

 

the blade guides and blade support bearings are clear

 

of the blade.

 

• After applying tension to the blade, open the upper

 

wheel guard.

 

• Rotate the wheel slowly forward by hand and observe

 

the blade’s movement. It should travel in the center of

 

the upper tire.

 

• If the blade creeps toward the front edge, unlock the

 

blade tracking lock (A) and turn the blade tracking

 

knob (B) clockwise until the blade consistently tracks

Figure 9

in the middle of the tire.

 

• If the blade creeps towards the rear of the tire, adjust

 

the blade tracking knob counterclockwise.

 

• Lock the blade tracking lock and close and lock the

 

upper wheel guard.

 

INSERT THROAT PLATE

See Figure 10.

Disconnect the machine from the power source!

Fit the throat plate (A) in the throat of the table so that the tab on the throat plate fits into the notch in table.

Check to ensure the front of the throat plate is not higher than the table surface. To adjust the height of the throat plate, rotate the two set screws (B) either up or down

Figure 10

SQUARE TABLE TO BLADE

Disconnect the machine from the power source!

Place a carpenters square (A) against the front and back side of the blade and check the alignment of the table. If the table is out of square, refer to Figure 11 and proceed as follows:

Raise the upper blade guide assembly by loosening the lock knob (B).

Loosen the flange nut (C) on the lower trunnion using a 12MM open end wrench and adjust the set screw until the table is square with the blade from the front and back.

Tighten the flange nut and use the square to confirm proper position of the table

Check the pointer on the tilt scale, located on the lower trunnion, and reset if necessary to read 0°.

Figure 11

11

Image 11
Contents 14 in. Steel Frame Band Saw Important Safety Instructions Table of ContentsGeneral Safety Rules Safety Guidelines DefinitionsRefer to them often and use them to instruct others Additional Specific Safety RulesAll grounded, cord-connected machines POWER CONNECTIONSMotor Specifications Grounding InstructionsMinimum Gauge Extension Cord EXTENSION CORDSFunctional Description KEY Features and ComponentsUnpacking Product SpecificationsAttaching the SAW to the Stand AssemblyStand Assembly Secure Table to Table Trunnion SystemInstall Band SAW Blade Install Blade Tensioning KnobSquare Table to Blade Adjust the Blade TrackingSee Figure Disconnect the machine from the power source Insert Throat PlateSelecting Proper Cutting Speed Using the Safety KEY to Lock the Switch in the OFF PositionOperation Starting and Stopping the SAWPositioning the Upper Blade Guide Disconnect the machine from the power source See FigureOperation Tilting the TableCutting Curves AdjustmentsAdjusting the Blade Tension Adjusting Blade Tracking Adjusting the Blade Guides and BearingsFailure to Start MaintenanceTroubleshooting Keep Machine CleanProbable Cause Trouble Band SAW does not Come UP to SpeedTips AccessoriesWarranty About Band SAW BladesService and Repairs Replacement PartsConsignes DE Sécurité Définitions Consignes DE Sécurité ImportantesSuite à la Règles DE Sécurité GénéralesConservez CES Consignes Règles DE Sécurité Spécifiques SupplémentairesInstructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur Fonctionnement monophasé 240 Volts RallongesDescription du FONCTIONNEment Caractéristiques ET ComposantesDéballage Caractéristiques DU ProduitFixer LA Scie AU Support MontageMontage DU Support Fixer LA Table AU Système DE Tourillons DE TableVoir Figure Installer LA Poignée DE Tension DE LA LameInstaller LA Lame DE LA Scie À Ruban Aligner LA Table ET LA Lame Régler LE Suivi DE LA LameInsérer LA Plaque Lumière Sélection DE LA Bonne Vitesse DE Coupe FonctionnementDémarrage ET Arrêt DE LA Scie Positionner LE Guide DE Lame Supérieur Incliner LA TableRégler LA Tension DE LA Lame AjustementsCouper DES Courbes Régler LE Suivi DE Lame Régler LES Guides DE Lame ET PaliersÉchec DU Démarrage Cause probable SolutionEntretien DépannageCause probable Cause probable Solution Curseur déréglé Réglez le curseurConseils AccessoiresPropos DES Lames DE Scie À Ruban GarantieService ET Réparations Aide Pour LES PIÈCES, LE Service OU LA GarantieNormas DE Seguridad Definiciones Instrucciones Importantes DE SeguridadContinúa en la página Reglas Generales DE SeguridadGuarde Estas Instrucciones Reglas Adicionales DE SeguridadInstrucciones DE Conexión a Tierra Conexiones DE AlimentaciónEspecificaciones DEL Motor Alargador Eléctrico DE Calibre Mínimo Alargadores EléctricosDescripción Funcional Características Y Componentes ClaveDesembalaje Especificaciones DEL ProductoConsulte la Figura EnsamblajeEnsamblaje DE LA Base Sujete LA Mesa AL Sistema DE Muñones DE MesaVea la figura Instale LA Perilla Tensionadora DE LA HojaInstale LA Hoja DE LA Sierra Cinta Cuadre LA Mesa a LA Hoja Ajuste DEL Desplazamiento DE LA HojaInserte LA Placa DE Garganta Selección DE LA Velocidad DE Corte Adecuada FuncionamientoEncender Y Detener LA Sierra Posicionamiento DE LA Guía DE LA Hoja Superior Inclinación DE LA MesaAjuste DE LA Tensión DE LA Hoja AjustesCorte DE Curvas De la fuente de alimentación Ajuste DE LAS Guías Y LOS Rodamientos DE LA HojaMantenga LA Máquina Limpia ReSOLUCIÓN DE ProblemasMantenimiento Falla EN EL EncendidoCausa probable Problema LA Sierra Cinta no Alcanza LA Velocidad DeseadaSugerencias Acerca DE LAS Hojas Para Sierra CintaAccesorios GarantíaServicio Técnico Y Reparaciones Asistencia Sobre GARANTÍA, Servicio O PiezasAirport Road Anderson, SC 800