Bostitch BTE300K Shoe adjustment, Adjusting for 90 Degree Cuts, Kerf Indicator Figure K

Page 9

shoe adjustment

 

I1

WARNING: ALWAYS TURN OFF AND

 

DISCONNECT TOOL BEFORE CHANGING

 

ACCESSORIES OR MAKING ANY

 

ADJUSTMENTS.

 

Your shoe has been factory set to assure that the

 

blade is perpendicular to the shoe. If after extended

 

use, you need to re-align the blade follow the

 

 

directions below:

 

I2

ADJUSTING FOR 90 DEGREE CUTS

1.Return the saw to 0 degrees bevel.

2.Place the saw on its side, and retract the lower guard.

3.Loosen the bevel adjustment lever (11). Place a square against the blade and the shoe as shown in figure I1.

4.Using a hex wrench, turn the set screw on the

underside of the shoe shown in figure I2 until the blade and the shoe are both in flush contact with the square. Retighten the bevel adjustment lever.

Making adjustments to the depth and bevel levers - (FIGURE J)

It may be desirable to adjust the depth

J

adjustment lever or the bevel adjustment

 

lever. They may loosen in time and hit the

 

shoe before tightening.

 

To adjust the levers, follow the steps

 

below:

 

• Remove retaining ring (shown in figure J)

 

and thin flat washer. Retain for reassembly.

 

• Remove the lever and rotate the lever one

 

position counter clockwise and slide lever

 

into feature.

 

• Reinstall flat washer and lock ring with the concave side against the lever.

Kerf Indicator (Figure K)

The front of the saw shoe has a kerf indicator for vertical and bevel cutting. This indicator enables you to guide the saw along cutting lines penciled on the material being cut. The indicator lines up with the left (inner) side of the saw blade, which makes the slot or “kerf” cut by the moving blade fall to the right of the indicator.

Additionally, the BTE300 has 0 and 45 degree visual indicators - the corresponding left and right sides of the window in the rip fence slot (see item 15 in Fig. K), and also labeled 0 and 45 degree indicators just in front of the blade kerf (see item 16 in Fig. K). removed from Fig. K for clarity.

K

15

16

Note that the upper guard has been

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 15A Work Area Safety Safety Guidelines DefinitionsAdditional SPEcIFIc Safety rULES Safety Instructions for All SawsCAUSES and OPErATOr PrEvENTION of kIckbAck Lower Guard Safety Instructions Total Length of Cord in Feet Functional Description Figure a SymbolsSupporting Large Panels / Securing Workpiece Adjusting the depth of cutfigURE F & G Assembly/ Set-UpIntended USE Shoe figures FAdjusting for 90 Degree Cuts Shoe adjustmentMaking adjustments to the depth and bevel levers Figure J To adjust the levers, follow the steps BelowGuard Against Kickback Attaching the blade FigURE MOperation SwitchPocket Cutting FIGURE O TroubleshootingReplacement Parts Service and Repairs Lignes directrices en matière de sécurité définitions Scie circulaires 7-1/4 184mm, 15 AmpèrePage Page CONSIGNES DE SÉcUrITÉ rELATIvES AU PrOTèGE-LAME INFÉrIEUr Résulter des blessures corporelles graves Directives de sécurité supplémentaires· le plomb dans les peintures à base de plomb SymbolesSoutien de grands panneaux/fixation de la pièce Description Fonctionnelle Figure aUtilisation Prévue Montage/RéglageRéglage de la profondeur de coupe fig. F et G Réglage de la semelle Mise EN Garde ToujoursRéglage Pour Coupes À 90 Degrés Fixation et dépose de la lame Dépose de la lame Fig. L Indicateur de trait de scie figure KAssemblage de la lame Fig. M Pare-main inférieurFonctionnement Fixation ET Depose D’UN Guide Longitudinal Figure nPROTÉGEZ-VOUS DES Effets DE Rebond InterrupteurDécoupe EN Poche Figure O Conseils pour une utilisation optimaleDépannage Rangement de la clé et des accessoiresEntretien Pièces DE RechangeRemplacement DES Étiquettes D’AVERTISSEMENT AccessoiresEntretien ET Réparation Garantie Limitée DE Trois ANSPautas DE SEGURIDAD/DEFINICIONES Page Peligro Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador Firmemente antes de utilizar la herramienta Madera antes de cortarSímbolos Descripción DE LAS Funciones Figura a Ensamblaje/Configuración USO PrevistoAjuste de la profundidad de corte fig. F, g Ajuste del ángulo de biselado Ajuste de zapataAjuste Para Cortes a 90 Grados Protector inferior de la hoja Colocación de la hoja FIG. MIndicador de corte Figura K De la Figura MIncluida en PC15TCSM Figura N Colocación Y Extracción DE UNA Guía DE Corte noFuncionamiento InterruptorCortes Internos FIGURA O Consejos para un uso óptimoProblema Detección de problemasAlmacenamiento Para LA Llave Y LOS Accesorios Causa posible Solución posiblePiezas DE Repuesto Mantenimiento Y Reparaciones MantenimientoAccesorios Garantía Limitada DE Tres AnosReemplazo DE LAS Etiquetas DE Advertencia Page Catalog Number BTE300 Form June
Top Page Image Contents