Delta 22-555 instruction manual Refer to them often and use them to instruct others

Page 5

ADDITIONAL SPECIFIC SAFETY RULES

12.Never reach into the cutterhead area while the machine is running. Your hands can be drawn into the knives.

13.Do not stand in line of the workpiece. Kickback can cause injury.

14.Allow the cutterhead to reach full speed before feeding a workpiece.

15.When planing bowed stock, place the concave (cup down) side of the stock on the table and cut with the grain to prevent kickback.

16.Do not feed a workpiece that is warped, contains knots, or is embedded with foreign objects (nails, staples, etc.). Kickback can occur.

17.Do not feed a short, thin, or narrow workpiece into the machine. Your hands can be drawn into the knives and/or the workpiece can be thrown at high speeds. See the “operation” section of this instruction manual for details.

18.Do not feed a workpiece into the outfeed end of the machine. The workpiece will be thrown out of the opposite side at high speeds.

19.Remove shavings only with the power “off” to prevent serious injury.

20.Properly support long or wide workpieces. Loss of control of the workpiece can cause serious injury.

21.Never perform layout, assembly or set-up work on the table/work area when the machine is running. Serious injury will result.

22.Turn the machine “off”, disconnect it from the power source, and clean the table/work area before leaving the machine. Lock the switch in the “off” position to prevent unauthorized use. Someone else might accidentally start the machine and cause injury to themselves or others..

23.Additional information regarding the safe and proper operation of power tools (i.E. A safety video) is available from the power tool institute, 1300 sumner avenue, cleveland, oh 44115-2851 (www. Powertoolinstitute.Com). Information is also available from the national safety council, 1121 spring lake drive, itasca, il 60143-3201. Please refer to the american national standards institute ansi 01.1 Safety requirements for woodworking machines and the u.S. Department of labor osha 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

5

Image 5
Contents 13 in. Bench Planer Important Safety Instructions Table of ContentsGeneral Safety Rules Safety Guidelines DefinitionsAdditional Specific Safety Rules Refer to them often and use them to instruct others Motor Specifications POWER CONNECTIONSGrounding Instructions All grounded, cord-connected machinesEXTENSION CORDS KEY Features and ComponentsFunctional Description Unpacking Product SpecificationsDescription Quantity Hardware PackageAttach Height Adjustment Handle AssemblyConnecting to Dust Collector Attach Reversible Dust PortResetting the ON-BOARD Circuit Breaker Locking the Planer Using the Safety KEYAdjusting Cutting Height OperationThere are a few ways you can control snipe Eliminating SnipeChanging or Reversing Knives MaintenanceOther Recommended Maintenance Five Year Limited Warranty AccessoriesWarranty Service and Repairs Replacement Parts Free Warning Label ReplacementPage Consignes DE Sécurité Définitions Consignes DE Sécurité ImportantesSuite à la Règles DE Sécurité GénéralesRègles DE Sécurité Spécifiques Supplémentaires Conservez CES Consignes Instructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur Rallonges Caractéristiques ET Composantes ImportantesDescription Fonctionnelle Déballage Caractéristiques DU ProduitDescription Quantité MatérielFixer LA Poignée DE Réglage DE LA Hauteur MontageFixer Lorifice Réversible Dévacuation DE LA Poussière Brancher LE Collecteur DE PoussièreDémarrer ET Arrêter LA Raboteuse FonctionnementVerrouiller LA Raboteuse AU Moyen DE LA CLÉ DE Sécurité Réinitialiser LE Disjoncteur IntégréIl y a peu de façons de contrôler une entaille Éliminer UNE EntailleChanger OU Inverser LES Lames Autre Entretien RecommandéEntretien Garantie Limitée DE Cinq ANS AccessoiresGarantie Service ET Réparations Aide Pour LES PIÈCES, LE Service OU LA GarantiePage Normas DE Seguridad Definiciones Instrucciones Importantes DE SeguridadContinúa en la página Reglas Generales DE SeguridadReglas Específicas DE Seguridad Adicionales Guarde Estas Instrucciones Instrucciones DE Conexión a Tierra Conexiones DE AlimentaciónEspecificaciones DEL Motor Descripción Funcional Características Y Componentes ClaveAlargadores Eléctricos Pulg Indicador de alturaDesempaque Especificaciones DEL ProductoDescripción Cantidad Paquete DE TornilleríaManivela DE Ajuste DE Altura EnsambleColoque EL Puerto DE Polvo Reversible Conexión AL Colector DE PolvoEncendido Y Apagado DEL Cepillo FuncionamientoBloqueo DEL Cepillo CON LA Llave DE Seguridad Restablecimiento DEL Interruptor DE Circuito IntegradoExisten varias maneras de controlar los biseles Eliminación DE BiselesCambio O Inversión DE LAS Cuchillas MantenimientoOtro Mantenimiento Recomendado Garantía Limitada DE Cinco Años AccesoriosGarantía Servicio Técnico Y Reparaciones Asistencia Sobre GARANTÍA, Servicio O PiezasPage Roush Street Anderson, SC 800