Simer Pumps 3310P, 3307P, 3305P Preparing to Start the Pump Shallow Well, Open Control Valve

Page 12

Preparing to Start the Pump – Shallow Well

12

Never run pump dry. Running pump with- out water may cause pump to overheat, damaging seal and possibly causing burns to persons handling pump. Fill pump with water before starting.

Never run pump against closed discharge. To do so can boil water inside pump, causing hazardous pressure in unit, risk of explosion and possibly scalding persons handling pump.

1.Open the control valve as far as possible (see Figure 18). Then remove the priming plug from the pump and fill the pump, fill all piping between the pump and the well, and make sure that all piping in the well is full. If you have also installed a priming tee in the suction piping, remove the plug from the tee and fill the suction piping.

Open control valve as far as possible and fill pump and piping through priming port

or priming tee.

284 0395

Figure 18: Open Control Valve

2.Replace all fill plugs. Leave the control valve open (in a shallow well installation, the control valve always stays open).

3.Power on! Start the pump. The pump should pump water in two or three minutes.

4.If you don’t have water after 2 or 3 minutes, stop the pump and remove the fill plugs. Refill the pump and piping. You may have to repeat this two or three times in order to get all the trapped air out of the pip- ing. The control valve remains open throughout this procedure.

5.After the pump has built up pressure in the system and shut off, check the pressure switch operation by opening a faucet or two and running enough water out to bleed off pressure until the pump starts. The pump should start when pressure drops to 30 PSI and stop when pressure reaches 50 PSI. Run the pump through one or two complete cycles to verify correct operation. This will also help clean the system of dirt and scale dislodged during installation.

Congratulations on a successful installation.

If you were unsuccessful, please refer to the Troubleshooting section (Page 13) or call our customer service technical staff.

For parts or assistance, call Simer Customer Service at 1-800-468-7867 /1-800-546-7867

Image 12

Contents Models 3305P, 3307P, 3310P Composer le 1 800 Llame alSafety Read and Follow Safety InstructionsElectrical Safety General SafetyTable of Contents Replacing an Existing Pump Deep WellShallow Well New Shallow Well Installation Cased Well INSTALLATION, 2 or Larger Casing FigureInstallation for Surface Water ScaleNew Deep Well Installation Or Larger Well FigureWell Figure Discharge Pipe and Pressure Tank Connections PRE-CHARGE Tank Connection FigureStandard Tank Connection Figure Electrical Dial Type Voltage SelectorWiring Connections Connection ProcedureWiring Chart Recommended Wire and Fuse Sizes Congratulations on a successful installation Preparing to Start the Pump Deep WellPreparing to Start the Pump Shallow Well Open Control ValveTroubleshooting Capacitor, hold insulated handle screwdriver by the HandleRepair Parts Model and HPPart 3305P 3307P 3310P Description 2HP 4HP Shallow Well Installation Ejector PackageShallow Well Kit FP4875 or Key Part Description NumberDeep Well Installation Double Pipe Kit FP4800 orSingle Pipe Kit FP4840 or Sécurité Lire Toutes CES Instructions ET LES SuivreSécurité Concernant Lélectricité Sécurité GénéraleTable des matières Garantie limitée SimerRemplacement dune pompe existante Puits ProfondsPuits PEU Profonds Installation sur un nouveau puits peu profond Installation DE LAPointe Filtrante Figure Installation Dans LE CAS Deaux EN Surface Poser léjecteurInstallation sur un nouveau puits profond Puits DE 2 Pouces FigureBranchement SUR UN Réservoir Standard Figure Électricité Sélecteur de tension à cadranConnexions DES Fils Félicitations pour une installation réussie Préparations avant le démarrage de la pompe Puits profondOuvrir la vanne de réglage Diagnostic des pannes Symptômes Causes Probables RemèdesPièces de rechange Modèle et puissance en ch3305P 3307P 3310p Désignation des piècesInstallation dans un puits peu profond Ensemble éjecteurTrousse pour puits peu profonds FP4875 ou Désignation Numéro Réf Des piècesInstallation dans un puits profond Désignation NuméroSeguridad LEA Y Siga LAS Instrucciones DE SeguridadSeguridad Electrica Seguridad GeneralIndice de Contenido Garantía limitada de SimerReemplazo de una Bomba Existente Pozo ProfundoPozo Poco Profundo Instalación de un Pozo Nuevo de Poca Profundidad Instalacion DEL Punto DE Pozo FiguraInstalacion Para Agua Superficial Figura 8 Instale el EyectorInstalación De Un Pozo Nuevo Profundo Pozo DE 4 Ó MAS FiguraPozo DE 2 Figura Conexión DE Tanque DE PRE- Carga Figura Conexión Para Tanque Estándar FiguraElectricidad Selector de tensión de tipo cuadranteÉléctricas y a Tierra Conexiones DE LOS CablesPreparación Para Arrancar La Bomba Pozo Profundo Felicidades por una instalación exitosaPreparación Para Arrancar La Bomba Pozo Poco Profundo Solución de Problemas Síntoma Causas Probables Acción CorrectivaRefacciones Modelo y HP3305P 3307P 3310P Descripción de la Parte Paquete eyector Instalación en pozos poco profundosDescripción Número de De la Parte Repuesto Instalación en pozos profundos Clave Descripción Número de De la Parte Repuesto