Makita DPC 7000 Puttinginto Operation, Installingthe drivearm and mountingthe cutting disc

Page 12

PUTTINGINTO OPERATION

Installingthe drivearm and mountingthe cutting disc

CAUTION: Alwavs turn off the enqine before doing any work on the drive arm or cutting disc. Pull the plug cap off the spark plug. Wear protective gloves!

CAUTION: Completely reassemble the Power Cut before starting the engine!

Use the assembly tool delivered with the Power Cut (see page 6) for the following works.

Place the Power Cut on a stable surface and follow these steps to install the drive arm and protection hood:

-Turnthe tighteningscrew (B/4)to the left (counter-clockwise) until the pin (B/5) is at the left stop.

-Pull the hand guard (D/10) all the way forward and hold as shown in Fig. D.

-Pressthe drive arm onto the housing with both hands. Make sure that the pin (B/5) fits into the space in the drive arm.

I -

-Unscrew retaining nut (Ah).

-Take off the sprocket guard (A/2) and unscrew the second retaining nut (A/3).

NOTE:The second retaining nut (A/3)protects against shipping damage.It is locatedunderneaththesprocket guard on the same threaded pin as the first retaining nut.

-Place the drive arm (C/6) over the two threaded pins (C/7) and press towards the V-belt wheel (C/8).

-Pull the V-belt (C/9) over the V-belt wheel.

II

-While continuing to hold the hand guard, put on the sprocket guard (E/2).

-Screw on the retaining nuts (Ell) hand-tight.

12

Image 12
Contents Owner’s Safety Manual Table of contents Thank you for purchasinga Makita productPacking On/Off VO switch Choke switchDelivery inventory SymbokGeneral precautions Working with the Power Cut requires high concentrationFuels/ Refuelling Fuel vaporsFeet 3 meters LOOfeet 30 metersFor cutting metal When guiding the Power Cut by hand, use the side mounting Kickbackand lock-inTo prevent kickback, observe the following To prevent lock-in, observe the followingCutting metals Transport and storage Use only original Makita spares and accessories When calling for help, give the following informationDPC 9500, DPC Identification plateHandle Choke Installingthe drivearm and mountingthe cutting disc Puttinginto OperationSee Safety INSTRUCTIONS, Fuels/ Refuelling@ Gasoline I 50l 25lCorrect mixture ratio Store fuel only in approved and marked containersPut the short-circuiting switch E/I in position 0STOP StartingtheengineCold startingStoppingtheengine RefuellingAdjustingthe carburetor Switch off the engine. StopRunning at idling speed, loosen the screw a little Clockwise direction until it comes to a noticeable stopCleaningthe protection hood ChangingtheV-beltCleaning/changing the air filter Replacingthe spark plugDrythoroughly Electrode gapWire bent at one end to form a hook Replacingthe suction headReplacing the starter cable Replacing the return spring Cuttingattachment in central /side positionDismountthe cutting attachment seel‘changingtheV-belt 13 17 16 15 Remove nuts and screwsfrom segment H/18Diamondcuttingdiscs GuidetrolleyWater tank Maindpressurewater systemInstructionsfor periodic maintenance Service, spare parts and guaranteeTrouble shootig DefectiveValve dirty DPC 7001, DPC Extract from the spare parts list DPC 7000, DPC DPC 9500, DPC17 5 18 19 20 21 Service d’atelier, piec Recherche de pannes SommaireEmballage Reglagedu carburaSymboles 5 4Instructions generales En la matiere ou de la personne chargee de ce travailEquipement de protection personnel Produitsde fonctionnement / Remplissagedes reservoirs 100feet 30 metres=porter I’equipement ’ de protection Sinon risque de torsion du disque II faut veiller constamment a avoir une bonne assise sureSoit libre et que personne ne soit en danger Et emp6cher la corrosionRebond kickback et freinage Nejamais tronqonner avec le segment montre sur lafigureComDortement et techniaue de travail \ \ Remarque Maintenance Premier secoursRespecter les prescriptions de prevoyance contre les Si vous appelez du secours, veuillez indiquerCaracteristiquestechniques Designationdes piecesDPC 7000, DPC DPC 9500, DPC Plaque signatiqueMise EN Route Montage du bras de transmission et de la decou PeuseTendre la courroie a @ @ Viseur est a la mBme hauteur que le repere exterieur deCarburants/ravitaillement63 Carburant I 50lRealisation du rapport correct du melange Remplissage des reservoirs Demarrer le moteurQui pourraient y 6tre tombees peuvent deteriorer le Moteur !Prenez donc soin de porter des v6tements nonPoussiereux et propres, d’utiliser des outils propres et De travailler a un endroit propre. Ne poser aucun chiffonRemplacer lacourroie Ll\Nettoyer le capot de protection Remplacementde bougie Nettoyer/ remplacer le filtre a airPrefiltre en mousse et filtre interieur Ecartementdes electrodesRemplacement de la crepine d’aspiration Remplacement du cordon de lancementRemplacementdu ressort de rappel Debarrassez-vousde Iancienressorten recourantau recyclageDemonter le dispositif Disques a decouper en diamant Le chariot de guidageLe reservoir deau La conduite deau au reseau / reservoirIndications de maintenance et d’entretien periodiques Maintenanceet reparationsPiecesde rechange Garantie Recherche de pannesPanne Observation OrigineExtrait de la liste des pieces de rechange DPC7000, DPC 7001 DPC9500, DPC23 24 Modele7000,7001PENNSYLVANlA Page Makita U.S.A., Inc Makita Canada Inc