Makita DPC 9501, DPC 7000, DPC 9500, DPC 7001 ChangingtheV-belt, Cleaningthe protection hood

Page 17

MAINTENANCE

ChangingtheV-belt

21

-Remove the cutting disc (see also “Cleaning the protective hood”).

-Loosen the knob (model 7000, 7001) or tightening toggle (model 9500,9501) (D/3) somewhat and swing the protec- tive hood (D/4) all the way back.

-Loosen the retaining nuts (D/1) and screw (D/7) somewhat.

-Loosen the tightening screw byturning it 2-3 turns to the left (counter-clockwise) using the Allen key (D/5) supplied with the Power Cut. This reduces the V-belt tension.

-Remove the retaining nuts (D/I) and sprocket guard (D/2).

-Turn the tightening screw to the left (counter-clockwise) all the way.

-Removethe cutter attachment (D/6).

CAUTION: Beforedoinganyworkon the Power Cutturn off the engine, remove the cutting disc, pull the plug cap off the spark plug and wear protective gloves!

CAUTION: Completely reassemble the Power Cut before starting the engine!

IMPORTANT:

Because many of the parts and assemblies not mentioned inthis Owner’s Manual arevital to the safety of the unit, and becauseall parts are subjectto a certain amount of wear and tear, it is importantfor your own safetythat you havethe unit checked and maintained regularly by a MAKITA service center.

13

\

-Loosen and unscrew screws (E/8).

-Pull off the hand guard (E/9) and remove the guard plate (E/10) from the drive arm.

-Removethe old V-belt or V-belt pieces. Clean out the inside of the drive arm with a brush.

-Fit a new V-belt (E/11) around the V-belt wheel (E/12) and into the drive arm.

-Fit on the guard plate and attach with screw (F/8)

-Pushthe hand guard (F/9) all the way onto the drive arm and tighten screw (FA 3) hand-tight.

-To install the drive arm and tighten the V-belt, see“1nstalling the Drive Arm and Mounting the Cutting Disc”and “Tighten- ing the V-Belt“.

Cleaningthe protection hood

Over time, the inside of the protective hood can become caked with material residue (especially from wet cutting), which if allowed to accumulate can hinder the free rotation of the cutting disc. For this reason the hood must be cleaned out from time to time.

- Removethecutting discandthesecond pressuredisc (G/14) (on Model 9500,9501 there is an adapter ring (G/15) before the pressure disc).

- Clean out residue from the interior of the hood (G/16) using a strip of wood or similar object

- Clean the shaft (G/17) and all disassembled parts with a cloth.

17

Image 17

Contents Owner’s Safety Manual Packing Table of contentsThank you for purchasinga Makita product Choke switch On/Off VO switchDelivery inventory SymbokWorking with the Power Cut requires high concentration General precautionsFuel vapors Fuels/ RefuellingFeet 3 meters LOOfeet 30 metersFor cutting metal Kickbackand lock-in When guiding the Power Cut by hand, use the side mountingTo prevent kickback, observe the following To prevent lock-in, observe the followingCutting metals Transport and storage When calling for help, give the following information Use only original Makita spares and accessoriesHandle Choke DPC 9500, DPCIdentification plate Puttinginto Operation Installingthe drivearm and mountingthe cutting discSee Safety INSTRUCTIONS, Gasoline I 50l 25l Fuels/ Refuelling@Correct mixture ratio Store fuel only in approved and marked containersStartingtheengineCold starting Put the short-circuiting switch E/I in position 0STOPStoppingtheengine RefuellingSwitch off the engine. Stop Adjustingthe carburetorRunning at idling speed, loosen the screw a little Clockwise direction until it comes to a noticeable stopChangingtheV-belt Cleaningthe protection hoodReplacingthe spark plug Cleaning/changing the air filterDrythoroughly Electrode gapReplacing the starter cable Wire bent at one end to form a hookReplacingthe suction head Dismountthe cutting attachment seel‘changingtheV-belt Replacing the return springCuttingattachment in central /side position Remove nuts and screwsfrom segment H/18 13 17 16 15Guidetrolley DiamondcuttingdiscsWater tank Maindpressurewater systemService, spare parts and guarantee Instructionsfor periodic maintenanceValve dirty DPC 7001, DPC Trouble shootigDefective 17 5 18 19 20 21 Extract from the spare parts listDPC 7000, DPC DPC 9500, DPC Sommaire Service d’atelier, piec Recherche de pannesEmballage Reglagedu carbura5 4 SymbolesEquipement de protection personnel Instructions generalesEn la matiere ou de la personne chargee de ce travail =porter I’equipement ’ de protection Produitsde fonctionnement / Remplissagedes reservoirs100feet 30 metres II faut veiller constamment a avoir une bonne assise sure Sinon risque de torsion du disqueSoit libre et que personne ne soit en danger Et emp6cher la corrosionComDortement et techniaue de travail Rebond kickback et freinageNejamais tronqonner avec le segment montre sur lafigure \ \ Remarque Premier secours MaintenanceRespecter les prescriptions de prevoyance contre les Si vous appelez du secours, veuillez indiquerDesignationdes pieces CaracteristiquestechniquesDPC 7000, DPC DPC 9500, DPC Plaque signatiqueMontage du bras de transmission et de la decou Peuse Mise EN RouteViseur est a la mBme hauteur que le repere exterieur de Tendre la courroie a @ @Realisation du rapport correct du melange Carburants/ravitaillement63Carburant I 50l Demarrer le moteur Remplissage des reservoirsMoteur !Prenez donc soin de porter des v6tements non Qui pourraient y 6tre tombees peuvent deteriorer lePoussiereux et propres, d’utiliser des outils propres et De travailler a un endroit propre. Ne poser aucun chiffonNettoyer le capot de protection Remplacer lacourroieLl\ Nettoyer/ remplacer le filtre a air Remplacementde bougiePrefiltre en mousse et filtre interieur Ecartementdes electrodesRemplacement du cordon de lancement Remplacement de la crepine d’aspirationDebarrassez-vousde Iancienressorten recourantau recyclage Remplacementdu ressort de rappelDemonter le dispositif Le chariot de guidage Disques a decouper en diamantLe reservoir deau La conduite deau au reseau / reservoirPiecesde rechange Indications de maintenance et d’entretien periodiquesMaintenanceet reparations Recherche de pannes GarantiePanne Observation OrigineDPC7000, DPC 7001 DPC9500, DPC Extrait de la liste des pieces de rechange23 24 Modele7000,7001PENNSYLVANlA Page Makita U.S.A., Inc Makita Canada Inc