Makita DPC 7000, DPC 9501, DPC 9500 Trouble shootig, Defective, Valve dirty DPC 7001, DPC

Page 24

Guarantee

MAKITA guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resultingfrom material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular guarantee conditions may exist. If you have any questions, please contact your salesman, who is responsible for the guarantee of the product.

Please note that we cannot accept any responsibility for damage caused by:

Disregard of the owner’s manual.

Non-performance of the required maintenance and cleaning.

Incorrect carburetor adjustment.

Normal wear and tear.

Obvious overloading due to permanent exceeding of the upper performance limits.

The use of other than original MAKITA cutting discs.

Use of force, improper use, misuse or accidents.

Damage from overheating due to dirt on the fan housing.

Work on the Power Cut by unskilled persons or inappropriate repairs.

Use of unsuitable spare parts or parts which are not original MAKITA parts, insofar as they have caused the damage.

Use of unsuitable or old oil.

Damage related to conditions arising from lease or rent contracts.

Cleaning, servicing and adjustment work is not covered by the guarantee. All repairs covered by the guarantee must be performed by a MAKITA service centre.

Trouble shootig

Malfunction

System

0bservation

Cause

Cutting disc does not

Clutch

Engine runs

Damage to clutch

start turning

Engine does not start

Ignition system

Ignition spark

Malfunction in fuel supply system, com-

only with difficulty

 

 

pression system, mechanical malfunction.

 

 

No ignition spark

Switch on STOP, fault or short-circuit in the

 

 

 

wiring, plug cap or spark plug defective.

 

Fuel supply

Fuel tank is filled

Choke in wrong position, carburetor defective,

 

 

 

suction head dirty, fuel line bent or interrupted.

 

Compression

Inside

Cylinder base packing ring defective, radial

 

system

 

shaft packings defective, cylinder or piston rings

 

 

 

defective

 

 

Outside

Spark plug does not seal.

 

Mechanical

Starter does not engage

Spring in starter broken, broken parts

 

malfunction

 

inside the engine.

 

~

 

 

Warm start difficulties

Carburetor

Fuel tank is filled

Wrong carburetor adjustment.

 

 

Ignition spark

 

Engine starts, but

Fuel supply

Fuel tank is filled

Wrong idling adjustment, suction heador

dies immediately

 

 

carburetor dirty.

 

 

 

Tank venting defective, fuel line interrupted,

 

 

 

cable defective, STOP switch defective. Starting

 

 

 

valve dirty (DPC 7001, DPC 9501).

Insufficient power

Severalsystems

Engine is idling

Air filter dirty, wrong carburetor adjustment,

 

may be involved

 

Tuffler clogged, exhaust channel in cylinder

 

simultaneously

 

:logged.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Owner’s Safety Manual Table of contents Thank you for purchasinga Makita productPacking On/Off VO switch Choke switchDelivery inventory SymbokGeneral precautions Working with the Power Cut requires high concentrationFuels/ Refuelling Fuel vaporsFeet 3 meters LOOfeet 30 metersFor cutting metal When guiding the Power Cut by hand, use the side mounting Kickbackand lock-inTo prevent kickback, observe the following To prevent lock-in, observe the followingCutting metals Transport and storage Use only original Makita spares and accessories When calling for help, give the following informationDPC 9500, DPC Identification plateHandle Choke Installingthe drivearm and mountingthe cutting disc Puttinginto OperationSee Safety INSTRUCTIONS, Fuels/ Refuelling@ Gasoline I 50l 25lCorrect mixture ratio Store fuel only in approved and marked containersPut the short-circuiting switch E/I in position 0STOP StartingtheengineCold startingStoppingtheengine RefuellingAdjustingthe carburetor Switch off the engine. StopRunning at idling speed, loosen the screw a little Clockwise direction until it comes to a noticeable stopCleaningthe protection hood ChangingtheV-beltCleaning/changing the air filter Replacingthe spark plugDrythoroughly Electrode gapWire bent at one end to form a hook Replacingthe suction headReplacing the starter cable Replacing the return spring Cuttingattachment in central /side positionDismountthe cutting attachment seel‘changingtheV-belt 13 17 16 15 Remove nuts and screwsfrom segment H/18Diamondcuttingdiscs GuidetrolleyWater tank Maindpressurewater systemInstructionsfor periodic maintenance Service, spare parts and guaranteeTrouble shootig DefectiveValve dirty DPC 7001, DPC Extract from the spare parts list DPC 7000, DPC DPC 9500, DPC17 5 18 19 20 21 Service d’atelier, piec Recherche de pannes SommaireEmballage Reglagedu carburaSymboles 5 4Instructions generales En la matiere ou de la personne chargee de ce travailEquipement de protection personnel Produitsde fonctionnement / Remplissagedes reservoirs 100feet 30 metres=porter I’equipement ’ de protection Sinon risque de torsion du disque II faut veiller constamment a avoir une bonne assise sureSoit libre et que personne ne soit en danger Et emp6cher la corrosionRebond kickback et freinage Nejamais tronqonner avec le segment montre sur lafigureComDortement et techniaue de travail \ \ Remarque Maintenance Premier secoursRespecter les prescriptions de prevoyance contre les Si vous appelez du secours, veuillez indiquerCaracteristiquestechniques Designationdes piecesDPC 7000, DPC DPC 9500, DPC Plaque signatiqueMise EN Route Montage du bras de transmission et de la decou PeuseTendre la courroie a @ @ Viseur est a la mBme hauteur que le repere exterieur deCarburants/ravitaillement63 Carburant I 50lRealisation du rapport correct du melange Remplissage des reservoirs Demarrer le moteurQui pourraient y 6tre tombees peuvent deteriorer le Moteur !Prenez donc soin de porter des v6tements nonPoussiereux et propres, d’utiliser des outils propres et De travailler a un endroit propre. Ne poser aucun chiffonRemplacer lacourroie Ll\Nettoyer le capot de protection Remplacementde bougie Nettoyer/ remplacer le filtre a airPrefiltre en mousse et filtre interieur Ecartementdes electrodesRemplacement de la crepine d’aspiration Remplacement du cordon de lancementRemplacementdu ressort de rappel Debarrassez-vousde Iancienressorten recourantau recyclageDemonter le dispositif Disques a decouper en diamant Le chariot de guidageLe reservoir deau La conduite deau au reseau / reservoirIndications de maintenance et d’entretien periodiques Maintenanceet reparationsPiecesde rechange Garantie Recherche de pannesPanne Observation OrigineExtrait de la liste des pieces de rechange DPC7000, DPC 7001 DPC9500, DPC23 24 Modele7000,7001PENNSYLVANlA Page Makita U.S.A., Inc Makita Canada Inc
Top Page Image Contents