Makita DPC 9501, DPC 7000, DPC 9500, DPC 7001 13 17 16 15, Remove nuts and screwsfrom segment H/18

Page 21

!

1

I

i

c

Swingthe protective hood up and guide the adjusting screw (F/6)through the hoodand theguidetrack(F/9), and hold in position.

Position the spacer ring (F/lO) as shown in Fig. F and hold. Swing the protective hood so that the adjusting screw is facing the hole in the bracket (F/11).

Push in the adjusting screw (the threads press against the guide track), put on the spring washer, and screw on the knob.

Mount the cutting disc (see "Mounting the Cutting Disc").

Repositioningthe cutting tachment (Model 9500,9501)

-Removethe cuttingdisc andpull the adapter ring andsecond pressure disc off the shaft (see also "Cleaning the Protective Hood").

-Dismountthe cutting attachment (see"Changing the V-belt").

13 17 16 15 12

-Loosen the tightening toggle (G/12) and turn the protective hood so that the large hole is facing the adjusting screw (G/13).

-Unscrew the toggle and remove the spring housing (G/14) along with bothwashers (G/15). Pull the adjusting screw out through the hole and take off the spacer ring (G/16) and the lock bushing (G/17).

IHi

-Remove nuts and screwsfrom segment (H/18).

NOTE:Additional tools required: 10mm box oropen-end wrench and combination pliers.

-Turn segment 90" and screw back down as shown in Figure I. Position the two longer screws (1/19)on the guide track.

IMPORTANT: The two segment screws under the drive arm must be installed in such a way that the heads are inside the protective hood (nuts outside).

Swing the protective hood so that the large hole near the guide track is facing the bracket hole (V20, J/20).

Pushthe lock bushing (J/17)ontothe adjusting screw (J/13) (place screw head in groove of bushing).

Place the washer (J/16) between the guide track (J/21) and bracket (J/20) and hold it there.

Guide the adjusting screw with the lock bushing through the protective hoodand press through the guide track, washer, and bracket (with the wedge of the bushing inthe guide-track slot).

Push the spring housing (J/14) and the two washers (G/15) onto the adjusting screw and screw on the tightening toggle (J/12).

Mountthe cutting attachment and protective hood inthe side position. See "Installingthe Drive Arm and Cutting Disc"and "Tightening the V-Belt".

Mount the cutting disc (see "Mounting the Cutting Disc").

21

Image 21

Contents Owner’s Safety Manual Table of contents Thank you for purchasinga Makita productPacking Choke switch On/Off VO switchDelivery inventory SymbokWorking with the Power Cut requires high concentration General precautionsFuel vapors Fuels/ RefuellingFeet 3 meters LOOfeet 30 metersFor cutting metal Kickbackand lock-in When guiding the Power Cut by hand, use the side mountingTo prevent kickback, observe the following To prevent lock-in, observe the followingCutting metals Transport and storage When calling for help, give the following information Use only original Makita spares and accessoriesDPC 9500, DPC Identification plateHandle Choke Puttinginto Operation Installingthe drivearm and mountingthe cutting discSee Safety INSTRUCTIONS, Gasoline I 50l 25l Fuels/ Refuelling@Correct mixture ratio Store fuel only in approved and marked containersStartingtheengineCold starting Put the short-circuiting switch E/I in position 0STOPStoppingtheengine RefuellingSwitch off the engine. Stop Adjustingthe carburetorRunning at idling speed, loosen the screw a little Clockwise direction until it comes to a noticeable stopChangingtheV-belt Cleaningthe protection hoodReplacingthe spark plug Cleaning/changing the air filterDrythoroughly Electrode gapWire bent at one end to form a hook Replacingthe suction headReplacing the starter cable Replacing the return spring Cuttingattachment in central /side positionDismountthe cutting attachment seel‘changingtheV-belt Remove nuts and screwsfrom segment H/18 13 17 16 15Guidetrolley DiamondcuttingdiscsWater tank Maindpressurewater systemService, spare parts and guarantee Instructionsfor periodic maintenanceTrouble shootig DefectiveValve dirty DPC 7001, DPC Extract from the spare parts list DPC 7000, DPC DPC 9500, DPC17 5 18 19 20 21 Sommaire Service d’atelier, piec Recherche de pannesEmballage Reglagedu carbura5 4 SymbolesInstructions generales En la matiere ou de la personne chargee de ce travailEquipement de protection personnel Produitsde fonctionnement / Remplissagedes reservoirs 100feet 30 metres=porter I’equipement ’ de protection II faut veiller constamment a avoir une bonne assise sure Sinon risque de torsion du disqueSoit libre et que personne ne soit en danger Et emp6cher la corrosionRebond kickback et freinage Nejamais tronqonner avec le segment montre sur lafigureComDortement et techniaue de travail \ \ Remarque Premier secours MaintenanceRespecter les prescriptions de prevoyance contre les Si vous appelez du secours, veuillez indiquerDesignationdes pieces CaracteristiquestechniquesDPC 7000, DPC DPC 9500, DPC Plaque signatiqueMontage du bras de transmission et de la decou Peuse Mise EN RouteViseur est a la mBme hauteur que le repere exterieur de Tendre la courroie a @ @Carburants/ravitaillement63 Carburant I 50lRealisation du rapport correct du melange Demarrer le moteur Remplissage des reservoirsMoteur !Prenez donc soin de porter des v6tements non Qui pourraient y 6tre tombees peuvent deteriorer lePoussiereux et propres, d’utiliser des outils propres et De travailler a un endroit propre. Ne poser aucun chiffonRemplacer lacourroie Ll\Nettoyer le capot de protection Nettoyer/ remplacer le filtre a air Remplacementde bougiePrefiltre en mousse et filtre interieur Ecartementdes electrodesRemplacement du cordon de lancement Remplacement de la crepine d’aspirationDebarrassez-vousde Iancienressorten recourantau recyclage Remplacementdu ressort de rappelDemonter le dispositif Le chariot de guidage Disques a decouper en diamantLe reservoir deau La conduite deau au reseau / reservoirIndications de maintenance et d’entretien periodiques Maintenanceet reparationsPiecesde rechange Recherche de pannes GarantiePanne Observation OrigineDPC7000, DPC 7001 DPC9500, DPC Extrait de la liste des pieces de rechange23 24 Modele7000,7001PENNSYLVANlA Page Makita U.S.A., Inc Makita Canada Inc