Makita DPC 9500, DPC 7000, DPC 9501 Fuels/ Refuelling@, Gasoline I 50l 25l, Correct mixture ratio

Page 14

NOTE: Tighten the Allen screw tightly. If this is not done, the cutting disc can slip during cutting.

Fuels/ Refuelling@

Gasoline I 50:l 25:l

other oil

1.O Us-gal. (3.7 I) 2.5 floz. (75 cm3) 5.0 floz. (150 cm3)

2.5Us-gal. (9.4 I) 6.4 floz. (189 cm3) 2.8 floz. (378 cm3)

A 5.0 Us-gaL(18.9 I) 12.8 floz. (378 cm3) 5.6 floz. (756 cm3)

Fuelmixture

The Power Cut is powered by a high-performance two-stroke engine. It runs on a mixture of gasoline and two-stroke engine oil.

The engine is designedfor unleaded regular gasolinewith amin. octane value of 91 ROZ. In case no such fuel is available, you can use fuel with a higher octane value. This will not affect the engine.

In order to obtain an optimum engine output and to protect your health and the environment use unleaded fuel only. Gasolinewhich contensalcoholshouldnot usedin MAKITA products.

For lubricating the engine use a two-stroke engine oil (quality grade: TC-3),which is added to the fuel. The engine has been designed for use of MAKITA high-performance two-stroke en- gine oil and a mixture ratio of only 50:l to protect the environ- ment. In addition, a long service life and reliable operation with a minimum emission of exhaust gases are ensured.

MAKITA high-performance two-stroke engine oil is available in the following sizes to suit your individual requirements:

1I order number 980 008 607 100 ml order number 980 008 606

In case MAKITA high-performance two-stroke engine oil is not available, it is urgently recommended to use a mixture ratio of 25:1, as otherwise optimum operation of the engine cannot be guaranteed.

-Fit the pressure disc (M/16) on the shaft, observing the flattened side of the shaft.

NOTE: The arbor hole of the pressure disc is shaped to fit the shaft. When puttingthe pressurediscon the shaft, turn itslightly until it fits.

-Screw in the Allen screw (M/15) by turning it to the left (counter-clockwise - left-hand thread!) and tighten by hand.

-Slowly turn the cutting disc until the stop hole of the V-belt wheel is visible in the drive-arm hole (M/18).

-Push the assembly tool (M/19) allthe way into the stop hole of the V-belt wheel. The shaft is now blocked.

-Tighten the Allen screw with the Allen key (M/20).

The correct mixture ratio:

50:l when using MAKITA high-performancetwo-stroke engi- ne oil, i. e. mix 50 parts gasoline with 1 part oil.

2 5 1 when usingothertwo-strokeengineoils, i. e. mix25parts gasoline with 1 part oil.

NOTE:

For preparing the fuel-oil mixture first mix the entire oil quantity with half of the fuel required, then add the remaining fuel. Thoroughly shake the mixture before filling it into the Power Cut tank.

It is notwise to add more engine oil than specified to ensure safe operation. This will only result in a higher production of combus- tion residues which will pollute the environment and clog the exhaust channel in the cylinder as well as the muffler. In addition, fuel consumption will rise and performance will de- crease.

Fuelstorage

Fuels haveonlyalimitedshelf-life.Buyonlyas muchasyou will use in 4 weeks.

Store fuel only in approved and marked containers.

AVOID SKIN AND EYE CONTACT

A

Mineral oil products degrease your skin. If your skin comes in contact with these substances repeatedly and for an extended period of time, it will desiccate. Various skin deseases may result. In addition, allergic reactions are known to occur.

Eyes can be irritated by contact with oil. If oil comes into your eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Owner’s Safety Manual Packing Table of contentsThank you for purchasinga Makita product Delivery inventory On/Off VO switchChoke switch SymbokGeneral precautions Working with the Power Cut requires high concentrationFeet 3 meters Fuels/ RefuellingFuel vapors LOOfeet 30 metersFor cutting metal To prevent kickback, observe the following When guiding the Power Cut by hand, use the side mountingKickbackand lock-in To prevent lock-in, observe the followingCutting metals Transport and storage Use only original Makita spares and accessories When calling for help, give the following informationHandle Choke DPC 9500, DPCIdentification plate Installingthe drivearm and mountingthe cutting disc Puttinginto OperationSee Safety INSTRUCTIONS, Correct mixture ratio Fuels/ Refuelling@Gasoline I 50l 25l Store fuel only in approved and marked containersStoppingtheengine Put the short-circuiting switch E/I in position 0STOPStartingtheengineCold starting RefuellingRunning at idling speed, loosen the screw a little Adjustingthe carburetorSwitch off the engine. Stop Clockwise direction until it comes to a noticeable stopCleaningthe protection hood ChangingtheV-beltDrythoroughly Cleaning/changing the air filterReplacingthe spark plug Electrode gapReplacing the starter cable Wire bent at one end to form a hookReplacingthe suction head Dismountthe cutting attachment seel‘changingtheV-belt Replacing the return springCuttingattachment in central /side position 13 17 16 15 Remove nuts and screwsfrom segment H/18Water tank DiamondcuttingdiscsGuidetrolley Maindpressurewater systemInstructionsfor periodic maintenance Service, spare parts and guaranteeValve dirty DPC 7001, DPC Trouble shootigDefective 17 5 18 19 20 21 Extract from the spare parts listDPC 7000, DPC DPC 9500, DPC Emballage Service d’atelier, piec Recherche de pannesSommaire Reglagedu carburaSymboles 5 4Equipement de protection personnel Instructions generalesEn la matiere ou de la personne chargee de ce travail =porter I’equipement ’ de protection Produitsde fonctionnement / Remplissagedes reservoirs100feet 30 metres Soit libre et que personne ne soit en danger Sinon risque de torsion du disqueII faut veiller constamment a avoir une bonne assise sure Et emp6cher la corrosionComDortement et techniaue de travail Rebond kickback et freinageNejamais tronqonner avec le segment montre sur lafigure \ \ Remarque Respecter les prescriptions de prevoyance contre les MaintenancePremier secours Si vous appelez du secours, veuillez indiquerDPC 7000, DPC DPC 9500, DPC CaracteristiquestechniquesDesignationdes pieces Plaque signatiqueMise EN Route Montage du bras de transmission et de la decou PeuseTendre la courroie a @ @ Viseur est a la mBme hauteur que le repere exterieur deRealisation du rapport correct du melange Carburants/ravitaillement63Carburant I 50l Remplissage des reservoirs Demarrer le moteurPoussiereux et propres, d’utiliser des outils propres et Qui pourraient y 6tre tombees peuvent deteriorer leMoteur !Prenez donc soin de porter des v6tements non De travailler a un endroit propre. Ne poser aucun chiffonNettoyer le capot de protection Remplacer lacourroieLl\ Prefiltre en mousse et filtre interieur Remplacementde bougieNettoyer/ remplacer le filtre a air Ecartementdes electrodesRemplacement de la crepine d’aspiration Remplacement du cordon de lancementRemplacementdu ressort de rappel Debarrassez-vousde Iancienressorten recourantau recyclageDemonter le dispositif Le reservoir deau Disques a decouper en diamantLe chariot de guidage La conduite deau au reseau / reservoirPiecesde rechange Indications de maintenance et d’entretien periodiquesMaintenanceet reparations Panne GarantieRecherche de pannes Observation Origine23 24 Extrait de la liste des pieces de rechangeDPC7000, DPC 7001 DPC9500, DPC Modele7000,7001PENNSYLVANlA Page Makita U.S.A., Inc Makita Canada Inc
Top Page Image Contents