Makita DPC 9500 Cleaning/changing the air filter, Replacingthe spark plug, Drythoroughly

Page 18

Cleaning/changing the air filter

II

-Pull out the choke, in order to prevent any dirt particles that may have fallen in from getting into the carburetor.

-Unscrew the wing-nut ( N l )and take off the air filter hood W2) .

-Carefullypull the paper cartridge with foam prefilter (A/3) up and off.

-Clean the O-ring (N5)and the area around it with a brush, then carefully take off the inner filter (N4).

CAREFUL:

Cover the intake opening with a clean cloth to prevent dirt particles from getting into the intake manifold.

-Removethe O-rings ( N 5 )(there is a second O-ring in the air filter hood (N2)). Clean the O-rings and O-ring bearing surfaceswith a cleancloth, and put the O-rings back in place.

-Remove the foam prefilter (B/6) from the paper cartridge (B/7).

Foam prefilter and inner filter

IMPORTANT:

Do not use fuel to clean the foam prefilter and inner filter

(N4)!

a

II

67

-If the foam prefilter(W6) and innerfilter (N4)aredirty, wash them with dishwashing liquid in lukewarm water.

-Drythoroughly!

NOTE:

Underverydustyconditions itwill be necessarytoclean the foam prefilterseveral timesdaily. If this is not possibleon-site, have a sufficient supply of reserve foam prefilters on hand.

Papercartridge

The papercartridge(B/7)filterstheintakeairthroughaveryfine paper filter laminate system. For this reason it must never be washed.

Replacethe cartridge periodically,and especially in case of poor performance, reduced engine speed, or smoky exhaust.

-Before reassembling the filter system, check the intake opening for dirt particles, and remove any found.

CAUTION:

If the air filter becomes damaged, replace immediately!

Pieces of cloth or large dirt particles can destroy the engine!

Replacingthe spark plug

CAUTION:

Do not touch the spark plug or plug cap if the engine is running (high voltage).

Switch off the engine before starting any maintenance work.

Ahot engine can cause burns. Wear protective gloves!

The spark plug must be replaced in case of damage to the insulator, electrode erosion (burn) or if the electrodes are very dirty or oily.

-Pull the plug cap (C/8) off the spark plug. Use only the combination wrench supplied with the saw to remove the spark plug.

Electrode gap

The electrode gap must be ,020" (0.5 mm).

Checking the ignition spark

-Unscrew the wing-nut (D/I) and take off the air filter hood (D/2).

-Carefully pull the paper cartridge with foam prefilter (D/3) up and off.

-ON/OFF switch in the "I"(ON) position.

-Using insulated pliers, pressthe sparkplug with the plug cap firmlyattachedagainstthescrewon thecover (not inthearea around the spark-plug hole!).

-Pull the starter cable hard.

If the function is correct, an ignition spark must be visible near the electrodes.

CAUTION: Use only BOSCH WSR 6F spark plug.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Owner’s Safety Manual Table of contents Thank you for purchasinga Makita productPacking Delivery inventory On/Off VO switchChoke switch SymbokGeneral precautions Working with the Power Cut requires high concentrationFeet 3 meters Fuels/ RefuellingFuel vapors LOOfeet 30 metersFor cutting metal To prevent kickback, observe the following When guiding the Power Cut by hand, use the side mountingKickbackand lock-in To prevent lock-in, observe the followingCutting metals Transport and storage Use only original Makita spares and accessories When calling for help, give the following informationDPC 9500, DPC Identification plateHandle Choke Installingthe drivearm and mountingthe cutting disc Puttinginto OperationSee Safety INSTRUCTIONS, Correct mixture ratio Fuels/ Refuelling@Gasoline I 50l 25l Store fuel only in approved and marked containersStoppingtheengine Put the short-circuiting switch E/I in position 0STOPStartingtheengineCold starting RefuellingRunning at idling speed, loosen the screw a little Adjustingthe carburetorSwitch off the engine. Stop Clockwise direction until it comes to a noticeable stopCleaningthe protection hood ChangingtheV-beltDrythoroughly Cleaning/changing the air filterReplacingthe spark plug Electrode gapWire bent at one end to form a hook Replacingthe suction headReplacing the starter cable Replacing the return spring Cuttingattachment in central /side positionDismountthe cutting attachment seel‘changingtheV-belt 13 17 16 15 Remove nuts and screwsfrom segment H/18Water tank DiamondcuttingdiscsGuidetrolley Maindpressurewater systemInstructionsfor periodic maintenance Service, spare parts and guaranteeTrouble shootig DefectiveValve dirty DPC 7001, DPC Extract from the spare parts list DPC 7000, DPC DPC 9500, DPC17 5 18 19 20 21 Emballage Service d’atelier, piec Recherche de pannesSommaire Reglagedu carburaSymboles 5 4Instructions generales En la matiere ou de la personne chargee de ce travailEquipement de protection personnel Produitsde fonctionnement / Remplissagedes reservoirs 100feet 30 metres=porter I’equipement ’ de protection Soit libre et que personne ne soit en danger Sinon risque de torsion du disqueII faut veiller constamment a avoir une bonne assise sure Et emp6cher la corrosionRebond kickback et freinage Nejamais tronqonner avec le segment montre sur lafigureComDortement et techniaue de travail \ \ Remarque Respecter les prescriptions de prevoyance contre les MaintenancePremier secours Si vous appelez du secours, veuillez indiquerDPC 7000, DPC DPC 9500, DPC CaracteristiquestechniquesDesignationdes pieces Plaque signatiqueMise EN Route Montage du bras de transmission et de la decou PeuseTendre la courroie a @ @ Viseur est a la mBme hauteur que le repere exterieur deCarburants/ravitaillement63 Carburant I 50lRealisation du rapport correct du melange Remplissage des reservoirs Demarrer le moteurPoussiereux et propres, d’utiliser des outils propres et Qui pourraient y 6tre tombees peuvent deteriorer leMoteur !Prenez donc soin de porter des v6tements non De travailler a un endroit propre. Ne poser aucun chiffonRemplacer lacourroie Ll\Nettoyer le capot de protection Prefiltre en mousse et filtre interieur Remplacementde bougieNettoyer/ remplacer le filtre a air Ecartementdes electrodesRemplacement de la crepine d’aspiration Remplacement du cordon de lancementRemplacementdu ressort de rappel Debarrassez-vousde Iancienressorten recourantau recyclageDemonter le dispositif Le reservoir deau Disques a decouper en diamantLe chariot de guidage La conduite deau au reseau / reservoirIndications de maintenance et d’entretien periodiques Maintenanceet reparationsPiecesde rechange Panne GarantieRecherche de pannes Observation Origine23 24 Extrait de la liste des pieces de rechangeDPC7000, DPC 7001 DPC9500, DPC Modele7000,7001PENNSYLVANlA Page Makita U.S.A., Inc Makita Canada Inc
Top Page Image Contents