Makita Comprehensive Guide to Carburetor Adjustment for Cordless Saws

Page 16

Adjustingthe carburetor

NOTE:

The grinding parts are equipped with an electronic ignition to limit the speed. The carburetor also has a fixed jet which cannot be adjusted.

At the factory the idling speed has been set to approx. 2,300l/min., but the running-in process of a new engine may require slight readjustment of the idling speed.

Set the idling speed with a screwdriver (width of blade: 4 mm).

Thescrewdrivershown (A/1) (order number 944340001) hasa molded-on lug to assist in adjustment.

For correct adjustment of the idling speed the following steps must be carried out:

1. Start the engine and run it until

I	it is warm (about 3	- 5 minutes).

	2. Switch off the engine. STOP
		0

3. Remove the cover with the air filter.

- Unscrewthe two screws (B/2) to the leftand right on the cover (B/3).

CAREFUL! This exposes the carburetor intake! Dust or dirt particles that get into the carburetor can ruin the engine! Make sure your clothing is free of dust and dirt particles, your tools are clean, and the working area is clean. Do not lay a cloth or similar material on the carburetor intake opening!

4.	Starttheengine	I,
5. Readjust the idling speed.
-	If the cut-off disc is still turning when the engine is running,
	unscrew the adjusting screw of the throttle valve (C/4) until
	the cut-off disc is no longer turning. When the engine is left
-	running at idling speed, loosen the screw a little.
	Now the acceleration from idling speed to maximum speed
	must be tested byabruptlyoperating the throttle lever. If the
	acceleration is too slow, the idling speed jet screw (C/5) must

be loosened slightly (max. 1/8of a revolution) and the throttle valve adjusting screw (C/4) tightened slightly.

If the engine cannot be adjusted as described under point 5, a basic adjustment must be carried out with the engine

switched off.

@

6.	Basicadjustment
-	Carefullyscrew the idling speed jet screw (C/5)to the right (in
-	a clockwise direction) until it comes to a noticeable stop.
	Now unscrew the adjusting screw approx. 1 1/8 of a revolu-
	tion to the left (in an anti-clockwise direction).
-	Starttheengine.	+$ ?+
-	The idling speed and the acceleration can be corrected by
	turning the idling speedjet screw (C/5).Turn in the screw to
	speed up, and turn out the screw to speed down the engine.

After adjusting the carburetor it is absolutely essential to replace the cover with the air filter (B/4).

16

Image 16

Contents Owner’s Safety Manual Thank you for purchasinga Makita product Table of contentsPacking On/Off VO switch Choke switchDelivery inventory SymbokGeneral precautions Working with the Power Cut requires high concentrationFuels/ Refuelling Fuel vaporsFeet 3 meters LOOfeet 30 metersFor cutting metal When guiding the Power Cut by hand, use the side mounting Kickbackand lock-inTo prevent kickback, observe the following To prevent lock-in, observe the followingCutting metals Transport and storage Use only original Makita spares and accessories When calling for help, give the following informationIdentification plate DPC 9500, DPCHandle Choke Installingthe drivearm and mountingthe cutting disc Puttinginto OperationSee Safety INSTRUCTIONS, Fuels/ Refuelling@ Gasoline I 50l 25lCorrect mixture ratio Store fuel only in approved and marked containersPut the short-circuiting switch E/I in position 0STOP StartingtheengineCold startingStoppingtheengine RefuellingAdjustingthe carburetor Switch off the engine. StopRunning at idling speed, loosen the screw a little Clockwise direction until it comes to a noticeable stopCleaningthe protection hood ChangingtheV-beltCleaning/changing the air filter Replacingthe spark plugDrythoroughly Electrode gapReplacingthe suction head Wire bent at one end to form a hookReplacing the starter cable Cuttingattachment in central /side position Replacing the return springDismountthe cutting attachment seel‘changingtheV-belt 13 17 16 15 Remove nuts and screwsfrom segment H/18Diamondcuttingdiscs GuidetrolleyWater tank Maindpressurewater systemInstructionsfor periodic maintenance Service, spare parts and guaranteeDefective Trouble shootigValve dirty DPC 7001, DPC DPC 7000, DPC DPC 9500, DPC Extract from the spare parts list17 5 18 19 20 21 Service d’atelier, piec Recherche de pannes SommaireEmballage Reglagedu carburaSymboles 5 4En la matiere ou de la personne chargee de ce travail Instructions generalesEquipement de protection personnel 100feet 30 metres Produitsde fonctionnement / Remplissagedes reservoirs=porter I’equipement ’ de protection Sinon risque de torsion du disque II faut veiller constamment a avoir une bonne assise sureSoit libre et que personne ne soit en danger Et emp6cher la corrosionNejamais tronqonner avec le segment montre sur lafigure Rebond kickback et freinageComDortement et techniaue de travail \ \ Remarque Maintenance Premier secoursRespecter les prescriptions de prevoyance contre les Si vous appelez du secours, veuillez indiquerCaracteristiquestechniques Designationdes piecesDPC 7000, DPC DPC 9500, DPC Plaque signatiqueMise EN Route Montage du bras de transmission et de la decou PeuseTendre la courroie a @ @ Viseur est a la mBme hauteur que le repere exterieur deCarburant I 50l Carburants/ravitaillement63Realisation du rapport correct du melange Remplissage des reservoirs Demarrer le moteurQui pourraient y 6tre tombees peuvent deteriorer le Moteur !Prenez donc soin de porter des v6tements nonPoussiereux et propres, d’utiliser des outils propres et De travailler a un endroit propre. Ne poser aucun chiffonLl\ Remplacer lacourroieNettoyer le capot de protection Remplacementde bougie Nettoyer/ remplacer le filtre a airPrefiltre en mousse et filtre interieur Ecartementdes electrodesRemplacement de la crepine d’aspiration Remplacement du cordon de lancementRemplacementdu ressort de rappel Debarrassez-vousde Iancienressorten recourantau recyclageDemonter le dispositif Disques a decouper en diamant Le chariot de guidageLe reservoir deau La conduite deau au reseau / reservoirMaintenanceet reparations Indications de maintenance et d’entretien periodiquesPiecesde rechange Garantie Recherche de pannesPanne Observation OrigineExtrait de la liste des pieces de rechange DPC7000, DPC 7001 DPC9500, DPC23 24 Modele7000,7001PENNSYLVANlA Page Makita U.S.A., Inc Makita Canada Inc