Black & Decker FS110L Starting and Stopping the Miter SAW, Locking the Switch in the OFF Position

Page 9

STARTING AND STOPPING THE MITER SAW

To start the miter saw, depress the switch trigger (A) Fig. 9. To stop the miter saw, release the switch trigger.

This saw is equipped with an automatic electric blade brake. As soon as the switch trigger (A) Fig. 9 is released, the electric brake is activated and stops the blade in seconds.

A turning saw blade can be dangerous. After completing the cut, release the switch trigger (A) Fig. 9 to activate the blade brake. Keep the cuttinghead down until the blade has come to a complete stop.

A

Fig. 9

The torque developed during braking may loosen the arbor screw. Check the arbor screw periodically and tighten, if necessary.

LOCKING THE SWITCH IN THE “OFF” POSITION

When the machine is not in use, the switch should be locked in the “OFF” position, using a padlock (B) Fig. 10 with a 3/16" diameter shackle to prevent unauthorized use.

B

Fig. 10

ROTATING THE TABLE FOR MITER CUTTING

Your miter saw will cut any angle from a straight 90° cut to 47° right and left. Loosen the lock handle (A) Fig. 11 one or two turns, depress the index lever (B), and move the control arm to the desired angle. TIGHTEN THE LOCK HANDLE (A).

The miter saw is equipped with positive stops at the 0°, 15.0°, 22.5°,31.62° and 45° right and left positions. Loosen the lock handle (A) Fig. 11, and move the control arm until the bottom of the index lever (B) engages into one of the positive stops (C) Fig. 12. TIGHTEN THE LOCK HANDLE (A) Fig. 11. To disengage the positive stop, depress the index lever (B).

In addition, an indicator (D) Fig. 11 is provided on the miter scale at the 33.9° right and left miter positions for cutting crown molding. (Refer to the “CUTTING CROWN MOLDING” section of this manual).

IMPORTANT: Always tighten the lock handle (A) Fig. 11 before cutting.

A

D

B

Fig. 11

Fig. 12

C

9

Image 9
Contents Before Returning this Product for ANY Reason Please Call FS110L 10 Compound Laser Miter SAWSafety Guidelines Definitions General Safety RulesImportant Safety Instructions Stay ALERT, Watch What YOU are Doing Failure to Follow These Rules MAY Result in Serious Injury Additional Safety Rules for Miter SawsPower Connections Additional Safety Rules for the LaserMotor Specifications Grounding InstructionsExtension Cords Unpacking and CleaningFunctional Description ForewordAssembly Carton ContentsAttaching Dust BAG Operating Controls and AdjustmentsFastening Machine to Supporting Surface Table Hazard AreaLocking the Switch in the OFF Position Starting and Stopping the Miter SAWRotating the Table for Miter Cutting Pointer and Scale Disconnect the Machine from Power SourceLocking Cuttinghead in the Down Position Tilting Cuttinghead for Bevel CuttingAdjusting Sliding Fence Rear STABILIZER/CARRYING HandleSide Supports Adjusting Downward Travel of SAW Blade Adjusting Blade Parallel to Table SlotAdjusting 90 and 45 Bevel Stops Disconnect Machine from Power SourceAdjusting Sliding FIT Between Cuttinghead ARM and Trunnion Adjusting Tension of Cuttinghead Return SpringAdjusting the Lower Blade Guard Laser USE and AdjustmentHOW to Check Laser Alignment HOW the Laser WorksTo SET Kerf Adjustment Laser MaintenanceTo Check for Vertical Alignment Typical Operations and Helpful Hints Auxiliary Wood FenceGeneral Cutting Operations Cutting Aluminum Cutting Bowed MaterialRight Wrong Cutting Crown Molding Crown MoldingChanging the Blade MaintenanceBrush Inspection Replacement Trouble Shooting Guide Mode D’EMPLOI Lignes Directrices EN Matière DE Sécurité Définitions Règles Générales DE SécuritéDirectives DE Sécurité Importantes Page Conserver CES Directives Connexions Électriques Règles DE Sécurité Supplémentaires Pour LE LaserCaractéristiques Techniques DU Moteur Directives DE Mise À LA TerreRallonges Électriques Description FonctionnelleDésemballage ET Nettoyage Contenu DU Carton AssemblageUtilisation DES Contrôle ET Réglages Verrouillage DE Linterrupteur EN Position Darrêt Démarrage ET Arrêt DE LA Scie À OngletsRotation DE LA Table Pour Effectuer UNE Coupe À Onglet Pointeur ET ÉchelleStabilisateur ARRIÈRE/POIGNÉE DE Transport Réglage DU Guide CoulissantSupports Latéraux Ajustement DE LA Lame Parralèle À LA Fente DE LA TableRéglage DU PROTÈGE-LAME Inférieur Utilisation ET Réglage DU LaserFonctionnement DU Laser Vérification DE L’ALIGNEMENT DU LaserVérification DE L’ALIGNEMENT Vertical Opérations Courantes ET Conseils UtilesRéglage DU Trait DE Scie Entretien DU LaserCoupe Daluminium Opérations DE Coupe GénéralesCoupe DE Matériau Arqué Moulure CouronnéeEntretien Inspection ET Remplacement DE LA BrosseGuide de dépannage Manual DE Instrucciones Definiciones DE LAS Normas DE Seguridad Normas Generales DE SeguridadInstrucciones Importantes Sobre Seguridad Page Conserve Estas Instrucciones Conexiones Eléctricas Otras Reglas DE Seguridad Para EL LáserEspecificaciones DEL Motor Instrucciones DE Conexión a TierraCables Prolongadores Descripción DE LAS FuncionesIntroducción Desembalaje Y Limpieza Contenido DE LA CajaMontaje Controles DE Operación Y Ajustes Bloqueo DEL Cabezal DE Corte EN LA Posición Hacia Abajo Indicador Y EscalaInclinación DEL Cabezal DE Corte Para EL Corte Biselado Ajuste DE LA Guía DeslizanteAjuste DEL Protector Inferior DE LA Hoja Ajuste DEL Recorrido Descendente DE LA Hoja DE LA SierraDesconecte LA Máquina DE LA Fuente DE Alimentación No Retire Ninguno DE LOS Protectores DE LA HojaFuncionamiento DEL Láser Utilización Y Regulación DEL LáserCómo Controlar LA Alineación DEL Láser Verificación DE LA Alineación VerticalMantenimiento DEL Láser Operaciones Típicas Y Consejos ÚtilesGuía Auxiliar Para Madera Operaciones Generales DE CorteMantenimiento Corte DE Material CurvadoMolduras DE Corona Importante Inspección Y Reemplazo DE LOS CepillosInformación de mantenimiento